Argos CHEVAL 3PIECE PACKAG ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 69cm
Depth - 49.5cm
Height - 200cm
Cheval - 2 Door Mirror Robe
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 31/01/14
Important - Please read these instructions fully before starting assembly
147/8985
151/7626
147/4549
151/3091
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 52kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
IMPORTANT INFORMATION ABOUT THIS PRODUCT
This product complies with the requirements of BS 7449:1991 and has been manufactured by
DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,
THORNABY-ON-TEES, CLEVELAND, TS17 9LT
.
The product code for this unit and the item code(s) for the glass components are listed in the Assembly
Instructions along with a description of the type of glass used. All clear/tinted glass complies with the requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the
glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,
or agent with regard to obtaining a manufacturing specification and shape for replacement glass
quoting the unit description and batch number or date of manufacture.
Do not place very hot or very cold items against or in close proximity to glass surface(s) unless
adequately thick insulating material is used to prevent such items coming in contact with the glass.
Do not strike the glass with hard or pointed items.
Do not sit or stand upon horizontal glass surfaces.
When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary - do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
Components - Panels
Please check you have all the panels listed below
2
1 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4
3
Top (D2721A)
(690 x 494mm)
5
Horizontal (D2722A)
(654 x 456mm) x 2
Back (X1890-674)
(1890 x 674mm)
Plinth (D2723A)
(654 x 86mm)
6
8
9
Hanging Rail (FHR646)
(646mm long)
7
Right Side (D2719A)
(1981 x 458mm)
Left Side (D2720A)
(1981 x 458mm)
Rail (D2724A)
(654 x 86mm) x 2
Mirror Door (D2725MA)
(1888 x 337mm) x 2
(Mirror - SG24 1817 x 260mm Safety Back SAR)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 18
B
Metal dowel (F901) x 14
C
D E
Large locking nut (F900) x 14
F
G H I
L
Nail (F51) x 35
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
Rail Holder (F891) x 2
19mm Screw (F461) x 4
13mm Screw (F63) x 1613mm Screw (F79) x 1
Bracket (F327) x 1
Handle (F274) x 2
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
40mm Screw (F910) x 4
Hinge (F518) x 6
Hinge plate (F523) x 6
N
Plastic Nail (F91) x 4
Finished
front edge
A
A
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left side
Tap 2 wooden dowels into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Screw 7 metal dowels into the left side .
Note: Tighten the metal dowels up fully against the panels.
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
Fit the rail holder to the left side using 2 screws .
To fit the rail holder, screw through its top hole and into the shallow mark hole drilled in the panel. Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Prepare the right side
Tap 2 wooden dowels into the right side .
Screw 7 metal dowels into the right side .
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
Fit the rail holder to the right side using 2 screws .
A
10mm
A
K
B
B
1
1
1
K
A
B
2
2
2
K
K
K
K
B
B
B
B
B
B
1
K
K
K
K
B
B
B
B
B
Finished
front edge
2
H
I
H
I
I
1
H
I
2
H
I
H
H
I
H
H
B
B
B
Finished
front edge
Finished
top edge
A
Finished
front edge
Finished
front edge
A
Assembly Instructions
5
Step 3
Step 4
Finished
front edge
A
A
A
C
C
C
C
Prepare the 2 horizontals
Tap 4 wooden dowels into each horizontal .
Insert 4 large locking nuts into each horizontal .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
A
4
4
C
C
x 2
4
4
4
Fit the 2 horizontals to the right side
Push the 2 horizontals onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted each horizontal .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 5
2
4
C
C
4
2
A
C
C
A
A
C
C
Prepare the plinth and the 2 rails
Tap 2 wooden dowels into the plinth and each of the 2 rails .
Insert 2 large locking nuts into the plinth and each of the 2 rails . .
Note: The plinth and the 2 rails can have a plain chipboard surface.
A
5
6
6
5
C
5
6
B
C
Note: The rails have a finished top edge.
Plain
chipboard
surface
x 2
Plain
chipboard
surface
Finished
front edge
Assembly Instructions
6
Step 6
2
Finished
top edge
5
6
Fit the plinth and rails
Push the plinth onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the plinth . .
Push the 2 rails onto the right side .
Use a screwdriver to tighten the large locking nuts fitted to the 2 rails .
2
C
5
5
2
C
6
6
Note: Support the plinth and the rails until the left side has been fitted in the next step.
5
6
Step 7
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 7 large locking nuts fitted to the horizontals , the plinth and the 2 rails . .
1
C
4
5
6
Note: The 2 rails have a finished top edge.
1
4
4
Finished
top edge
6
6
E
E
E
E
Assembly Instructions
7
Step 8
Step 9
Fit the top and the plastic nails
Push the top onto the assembly and secure it to the sides and using 4 screws .
Tap 2 plastic nails into the bottom edge of each of the sides and . as shown.
3
1 2
E
2
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, making sure it is pushed up against the top .
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
9
3
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
y
y
x
D
Warning: The unit is heavy. Lift with care.
3
9
1
3
Finished
front edge
9
N
N
N
1
2
N
N
x
Assembly Instructions
8
Step 10
Step 11
7
I
Fit the hanging rail
Push the hanging rail . into the rail holders fitted to the side panels.
7
I
L
H
H
90
L
L
H
H
L
H
H
Prepare the 2 doors
Push fit 3 hinges into each of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
H
L
8
8
x 2
7
Warning: Glass! Handle with care
Assembly Instructions
9
Step 12
Fit doors and handles
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each door using 2 screws .
L
L
L
K
K
K
L
K
M
F
8
8
e:
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
F
M
F
8
M
8
Warning: Glass! Handle with care
Assembly Instructions
10
Step 13
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2965
Step 14
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The unit is heavy. Lift with care.
Assembly is complete
J
J
G
J
J
G
J
G
J
J
IMPORTANT
If you have purchased the Cheval Overbed
Cupboards, you will need to fix them to the
wall BEFORE you fix the Robe to the wall.
MADE IN
BRITAIN
Dimensions
Width - 38.5cm
Depth - 36cm
Height - 58cm
Cheval - Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 13/03/14
Important - Please read these instructions fully before starting assembly
147/3100
152/7939
146/1480
152/8794
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 12kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2734A)
(383 x 360mm)
Right Side (D2735A)
(562 x 318mm)
Rail (D2737A)
(348 x 66mm) x 2
Drawer Front (D2738A)
(364 x 164mm) x 3
Drawer Base (T322-297)
(322 x 297mm) x 3
Back (X515-370)
(515 x 370mm)
Left Drawer Side (W300-124LH)
(300 x 124mm) x 3
Right Drawer Side (W300-124RH)
(300 x 124mm) x 3
Left Side (D2736A)
(562 x 318mm)
4
5
6
7 8 9
10
Drawer Back (W311-124)
(311 x 124mm) x 3
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
D E
Large locking nut (F900) x 8
F
G H I
K
Small locking nut (F3) x 6
C
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
9mm Screw (F74) x 6 9mm Screw (F73) x 12
L
Knock-in Peg (F171) x 12
Plastic Nail (F91) x 4
Drawer runner (F1004) x 6
Handle (F273) x 3
19mm Screw (F461) x 6
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 12
M
Wedgefix (F639) x 6
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
B
E
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the 3 drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
E
7
8
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
5
E
E
7 8
E
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
E
7
8
B
B
5
7
8
K
5
Assembly Instructions
5
Step 4
K
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 7
9
7 8
5
6
7 8
9
6
6
K
7 8
K
x 3
x 3
9
7
8
7
8
9
6
K
Step 6
Attach the handle
Attach a handle to each drawer front using 2 screws .
L
G
5
x 3
x 3
5
G
G
L
M
M
M
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
M
Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
I
J
I
J
I
J
I
J
D
D
I
I
I
D
Prepare the left side
a: Place 3 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 2 metal
dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
1
I
I
D
1
1
J
J
B
1
a:
b:
c:
B
B
1
1
1
Assembly Instructions
7
Step 9
Finished
front edge
I
J
Finished
front edge
I
J
I
J
I
J
Finished
front edge
Finished
front edge
D
D
B
B
Prepare the right side
a: Place 3 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 2 metal
dowels into the right side .
Insert 2 large locking nuts into the right side .
2
I
I
D
2
2
J
J
B
2
a:
b:
c:
2
2
2
I
I
I
A
Assembly Instructions
8
Step 10
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels into each rail .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into each rail .
A
4
D
4
4
x 2
4
4
2
4
4
Fit the 2 rails
Push the 2 rails onto the right side .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
D
4
Step 11
D
B
4
2
D
Fit the left side
Push the left side onto the 2 rails .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
D
4
Step 12
1
4
1
Note: Support this rail until the left side has been fitted in the next step.
Note: The 2 rails can have a plain chipboard surface.
Plain
chipboard
surface
Assembly Instructions
9
Step 13
B
B
B
B
Finished
front edge
Prepare the top
Screw 4 metal dowels into the top .
B
3
3
1
2
3
Fit the top
Push the top onto the sides and .
Use a screwdriver to tighten the 2 large locking nuts fitted to each side and .
Step 14
3
1 2
D
1 2
Assembly Instructions
10
Step 15
y
y
x
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, making sure it is pushed up aganst the top .
Nail along the side edges and the bottom edge of the back .
Note: Nails should be spaced out evenly.
10
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
C
x
10
Step 16
Fit the plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . as shown.
Carefully stand the unit up for the next step.
F
F
F
F
F
1
2
2
1
3
3
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2968
Step 17
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
H
J
H
H
2nd threaded
hole
J
H
7 8
H
H
MADE IN
BRITAIN
Dimensions
Width - 38.5cm
Depth - 36cm
Height - 58cm
Cheval - Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 03/06/15
Important - Please read these instructions fully before starting assembly
147/3100
152/7939
146/1480
152/8794
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 12kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2734A)
(383 x 360mm)
Right Side (D2735A)
(562 x 318mm)
Rail (D2737A)
(348 x 66mm) x 2
Back (X515-370)
(515 x 370mm)
Left Drawer Side (W300-124LH)
(300 x 124mm) x 3
Right Drawer Side (W300-124RH)
(300 x 124mm) x 3
Left Side (D2736A)
(562 x 318mm)
4
5
6
7 8 9
10
Drawer Front (D2738B)
(364 x 164mm) x 3
Drawer Base (T325-297)
(325 x 297mm) x 3
Drawer Back (W314-124)
(314 x 124mm) x 3
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
D E
Large locking nut (F900) x 8
F
G H I
K
Small locking nut (F3) x 6
C
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
9mm Screw (F74) x 6 9mm Screw (F73) x 12
L
Knock-in Peg (F171) x 12
Plastic Nail (F91) x 4
Drawer runner (F1004) x 6
Handle (F273) x 3
19mm Screw (F461) x 6
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 12
M
Wedgefix (F639) x 6
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
B
E
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the 3 drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
E
7
8
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
5
E
E
7 8
E
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
E
7
8
B
B
5
7
8
K
5
Assembly Instructions
5
Step 4
K
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 7
9
7 8
5
6
7 8
9
6
6
K
7 8
K
x 3
x 3
9
7
8
7
8
9
6
K
Step 6
Attach the handle
Attach a handle to each drawer front using 2 screws .
L
G
5
x 3
x 3
5
G
G
L
M
M
M
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
M
Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
I
J
I
J
I
J
I
J
D
D
I
I
I
D
Prepare the left side
a: Place 3 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 2 metal
dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
1
I
I
D
1
1
J
J
B
1
a:
b:
c:
B
B
1
1
1
Assembly Instructions
7
Step 9
Finished
front edge
I
J
Finished
front edge
I
J
I
J
I
J
Finished
front edge
Finished
front edge
D
D
B
B
Prepare the right side
a: Place 3 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 2 metal
dowels into the right side .
Insert 2 large locking nuts into the right side .
2
I
I
D
2
2
J
J
B
2
a:
b:
c:
2
2
2
I
I
I
A
Assembly Instructions
8
Step 10
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels into each rail .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into each rail .
A
4
D
4
4
x 2
4
4
2
4
4
Fit the 2 rails
Push the 2 rails onto the right side .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
D
4
Step 11
D
B
4
2
D
Fit the left side
Push the left side onto the 2 rails .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
D
4
Step 12
1
4
1
Note: Support this rail until the left side has been fitted in the next step.
Note: The 2 rails can have a plain chipboard surface.
Plain
chipboard
surface
Assembly Instructions
9
Step 13
B
B
B
B
Finished
front edge
Prepare the top
Screw 4 metal dowels into the top .
B
3
3
1
2
3
Fit the top
Push the top onto the sides and .
Use a screwdriver to tighten the 2 large locking nuts fitted to each side and .
Step 14
3
1 2
D
1 2
Assembly Instructions
10
Step 15
y
y
x
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, making sure it is pushed up aganst the top .
Nail along the side edges and the bottom edge of the back .
Note: Nails should be spaced out evenly.
10
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
C
x
10
Step 16
Fit the plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . as shown.
Carefully stand the unit up for the next step.
F
F
F
F
F
1
2
2
1
3
3
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2968
Step 17
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
H
J
H
H
2nd threaded
hole
J
H
7 8
H
H
MADE IN
BRITAIN
Dimensions
Width - 71cm
Depth - 36cm
Height - 107cm
Cheval - 5+2 Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 13/03/14
Important - Please read these instructions fully before starting assembly
146/3093
151/4186
145/2561
147/2558
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 31kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2 4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D2749A)
(1054 x 318mm)
Right Side (D2750A)
(1054 x 318mm)
Upright (D2752A)
(167 x 318mm)
3
Top (D2751A)
(710 x 360mm)
Large Drawer Front (D2753A)
(692 x 164mm) x 5
Left Drawer Side (W300-124LH)
(300 x 124mm) x 7
Right Drawer Side (W300-124RH)
(300 x 124mm) x 7
Small Drawer Back (W293-124)
(293 x 124mm) x 2
Large Drawer Back (W639-124)
(639 x 124mm) x 5
Small Left DrawerFront (D2754A)
(344 x 164mm)
Small Right Drawer Front (D2770A)
(344 x 164mm)
Rail (D2755A)
(675 x 66mm) x 2
Small Drawer Base (T304-297)
(304 x 297mm) x 2
Large Drawer Base (T650-297)
(650 x 297mm) x 5
Back (X1007-700)
(1007 x 700mm)
5
8
6 7
9 10
11 12
13 14
15
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill (do not use for fitting screws)
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 24
D E
Large locking nut (F900) x 10
F
G H
M
I
K
Small locking nut (F3) x 14
C
J
9mm Screw (F74) x 14 9mm Screw (F73) x 28
L N
Knock-in Peg (F171) x 28
Plastic Nail (F91) x 4
Drawer runner (F1004) x 14
Handle (F273) x 7
19mm Screw (F461) x 14
Nail (F51) x 23
Wedgefix (F639) x 24
O
13mm Screw (F79) x 1
Bracket (F327) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
B
B
B
E
Step 2
Prepare the small left and right drawer fronts
Screw 2 metal dowels into the small left drawer front and the small right drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
9
10
Prepare 2 pairs of drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
E
6
7
Attach the drawer sides to the small drawer fronts
Push the left drawer side . and right drawer side . onto the back of the 2 small drawer fronts and .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
9
10
E
E
6 7
E
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
E
6
7
B
B
B
B
9 10
9 10
6
7
Note: The small right drawer front has a shallow identification mark.
Assembly Instructions
5
Step 4
N
N
Fit the small drawer base
Slide the small drawer base down the grooves in the drawer sides and and down into the groove in the small drawer fronts . and .
Step 5
Fit the small drawer back
Fit the small drawer back . between the drawer sides and .
Make sure that the small drawer base fits into the groove in the small drawer back .
Hold the small drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
13
6 7
9 10
6
12
7
13
12
12
N
6 7
Attach the handle
Attach a handle to each small drawer front . and using 2 screws .
L
G
9 10
N
x 2
x 2
x 2
13
6
7
N
9 10
6
12
13
7
G
G
L
9 10
Step 7
x 2
M
Fit the wedgefixes
Turn the 2 small drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
M
M
M
8
Assembly Instructions
6
Step 8
x 5
x 5
x 5
x 5
B
E
Step 9
Prepare the 5 large drawer fronts
Screw 2 metal dowels into each of the large drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
8
Prepare 5 pairs of drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 10
E
6
7
Attach the drawer sides to the large drawer fronts
Push the left drawer side . and right drawer side . onto the back of the 5 large drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
8
E
E
6 7
E
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
E
E
6
7
6
7
B
B
8
8
Assembly Instructions
7
Step 11
N
N
Fit the large drawer base
Slide the large drawer base down the grooves in the drawer sides and and down into the groove in the large drawer front .
Step 12
Fit the large drawer back
Fit the large drawer back . between the drawer sides and .
Make sure that the large drawer base fits into the groove in the large drawer back .
Hold the large drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 13
14
6 7
8
6
11
7
14
11
11
N
6 7
Attach the handle
Attach a handle to each large drawer front . using 2 screws .
Step 14
L
G
8
N
x 5
x 5
x 5
x 5
14
6
7
N
6
11
14
7
M
M
M
M
M
Fit the wedgefixes
Turn the large drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
M
G
G
L
8
Assembly Instructions
8
Step 15
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
I
J
D
Prepare the left side
a: Place 6 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 2 metal
dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
1
I
I
D
1
1
J
J
B
1
b:
a:
c:
I
J
I
J
I
J
I
J
I
J
I
J
1
1
1
I
I
I
I
I
I
B
B
D
D
Assembly Instructions
9
Step 16
Finished
front edge
I
J
Prepare the right side
a: Place 6 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 2 metal
dowels into the right side .
Insert 2 large locking nuts into the right side .
2
I
I
D
2
2
J
J
B
2
a:
b:
c:
Finished
front edge
Finished
front edge
Finished
front edge
I
J
I
J
I
J
I
J
I
J
I
J
I
I
I
I
I
I
B
B
D
D
2
2
2
A
Assembly Instructions
10
Step 17
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels into each rail .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into each rail .
A
5
D
5
Fit the 2 rails
Push the 2 rails onto the right side .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
D
5
Step 18
D
B
5
2
D
Fit the left side
Push the left side onto the 2 rails .
Use a screwdriver to tighten the large locking nut fitted to each rail . .
D
5
Step 19
1
5
D
D
A
x 2
Note: Support this rail until the left side has been fitted in the next step.
5
5
2
5
5
1
plain chipboard surface
5
plain chipboard surface
plain chipboard surface
Finished
front edge
Assembly Instructions
11
Step 20
Prepare the upright
Note: The colour of the upright may differ from the main unit colour or may be plain chipboard.
a: Place a runner on
the upright as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
Insert 2 large locking nuts into the upright . .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the upright .
Turn the upright over
c: Place a runner on
the upright as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
d: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the upright .
4
I
I
D
4
4
J
4
I
J
J
I
4
J
Finished
front edge
I
J
Turn the upright over
a:
b:
c:
d:
Note: Due to the manufacturing process, the 2 holes for the large locking nuts can be on either surface of the upright.
Finished
front edge
I
J
I
J
D
D
4
Finished
front edge
4
Finished
front edge
I
Finished
front edge
I
J
I
4
4
Assembly Instructions
12
Step 21
Step 22
B
B
B
B
B
B
Finished
front edge
Prepare the top
Screw 6 metal dowels into the top .
B
3
3
Fit the upright and bracket to the top
Push the upright down onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the upright .
Fix the bracket to the top , 175mm in from the side and flush to the back edge, using screw . .
Step 23
D
O
3
4
4
Remember: The 2 holes for the large locking nuts can be on either surface of the upright.
Finished
front edge
3
4
1
K
O
175mm
O
3
K
Fit the top
Push the top onto the sides and .
Use a screwdriver to tighten the 2 large locking nuts fitted to each side and .
3
1 2
D
1 2
3
2
Assembly Instructions
13
Step 24
y
y
x
x
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
15
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
15
C
15
Step 25
Fit the plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . as shown.
Carefully stand the unit up for the next step.
F
F
F
1
2
F
F
1
2
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 26
O
Secure unit to a wall
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the metal bracket fitted to the top .
Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.
3
WALL
WALL
O
3
O
Step 27
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
H
J
H
H
2nd threaded
hole
J
H
7 8
Warning: Take care when
drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Top of unit
H
H
ALR2969
Loading...