Page 1
Chelsea - 3 Door Display Cabinet
Assembly Instructions - Please keep for future reference 262/8246
Dimensions
Width - 129.3cm
Depth - 45cm
Height - 199.8cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6403030
BK02900 - Issue 1 - 29/05/2014
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• Do not use extended drawers
to aid standing. Do not stand on
extended drawers.
• Do not over load drawers,
the maximum load per drawer
should not exceed 3kg
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
Care and maintenance - Non compliance with this information may affect your guarantee
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• Doors and drawers should
be secured or removed before
moving.
• Electrical fittings must be fitted
with a 3-amp fuse to BS1362.
Disconnect from the source of
power before changing bulbs.
Replace bulbs with the same
type and wattage.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all boths and fittings are
tightened properly.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6403030
Display top
1
(131.6 x 129.3 x 34cm)
Display Base
2
(68.2 x 128.6 x 45cm)
2
Page 4
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
A
15mm Screw x 1 15mm Washer x 2
D
Multi socket adapter x 1
B C
E
12mm Screw x 4
Wall strap x 1
F
Connecting bracket x2
The following components are pre-fi tted and are illustrated for reference only.
Cup handle x 3 20mm Handle screw x 11
Oval handle x 5
Display light [with bulb] x 2
Tools required
Phillips screwdriver
(medium)
Step Ladder
(or equivalent)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50
55 60
65 70 75 80
85 90 95 100
110 115 120 125 130 135 140 145 150
155 160
165 170
The screws length is measured from the head to the point (30mm screw shown) .
3
Page 5
Assembly Instructions
Assembly Instructions
Step 1
Joining the Top to the
Base
a: Position display base
2
slightly away from
the wall in the position
required [please note it
will be hard to move once
assembled]. When in
place sit the display top
1
on top of the display
2
base
backs of the two units
and centralize the top on
the base.
and align the
a:
1
2
Step 2
b: Take one of the
connecting brackets
H
and a 12mm screw
G
and using philips
screwdriver fi x the plate
to the top of the base unit
and then to the bottom of
the top unit.
Repeat b on the other sid
of the unit
b:
1
F
E
2
Philips screwdriver
4
4
Page 6
Assembly Instructions
Step 2
Remove and replace
handle
a:
a: The cup and oval
handles are fi tted to the
inside of the unit, using
a Philips screwdriver
unscrew the 20mm
handle screws in each
handle and remove both
the 20mm handle screw
and the cup and oval
handle.
b: Replace the cup and
oval handle on the front
of the unit. Fix in position
by screwing the 20mm
handle screw into each
cup and oval handle from
inside the unit using a
Philips screwdriver.
1
2
20mm handle screw
Philips screwdriver
b:
Oval handle
1
Cup handle
Oval handle
Philips screwdriver
20mm handle screw
5
2
Page 7
Assembly Instructions
Step 3
Connecting display
lights
a: The display light is
fi xed to the light pelmet
inside the display
cabinet. Push the the
fi tting on the end of the
cable through the hole in
the back panel.
a:
1
connection from display light
b: Connect the socket on
the display light into the
connection on the multi
D
socket adapter
can now connect to the
mains.
Note: the light display
light fi tting has is own on
/ off switch on the back of
the fi tting
Warning:
Always turn the
lights of at the
mains when changing the
bulb.
E
. You
b:
Connection from display light
D
6
Page 8
Assembly Instructions
Step 4
Fixing to wall
It is recommended that
the unit is fi xed to a wall
Fix wall strap
C
to the
back of the unit using
A
15mm screw
15mm washer
and
B
.
Warning: The
15mm screw
A
is for fi xing the
C
wall strap
to furniture
only. In addition to this
you will need to choose
a screw or fi tting which is
suitable for securing the
C
wall strap
to the type
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
Step 5
Adjusting doors
1. To adjust the height /
level of the door loosen
all screw ‘A’s on all hinge
plates, level the door
height and retighten all
screw ‘A’s.
Back Panel
Unit Top
B
A
Using the correct type of
C
screw, screw through the
washer and wall strap
into a pre-drilled hole in
the wall
A
B
A
2. To adjust the gap
between the doors
loosen screw ‘B’, then
turn screw ‘C’ clockwise
to close the gap or
anticlockwise to increase
the gap. Re-tighten
screw ‘B’ to lock position.
3. To adjust the distance
away from the unit
loosen screw ‘B’, this
allows the hinge arm
to slide back and forth.
Adjust as required then
re-tighten screw ‘B’.
Assembly is complete.
7
C
1
2
3
Page 9
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6403030
8
Loading...