Argos Chadwick - Desk ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 100cm

Depth - 45cm

Height - 72cm

Chadwick - Desk

Assembly Instructions - Please keep for future reference

356/2246

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 16/10/14

Important - Please read these instructions fully before starting assembly

330/1074

322/8865

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 19kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

Left Side (D2911A)

(706 x 394mm)

Top (D2915A)

(1000 x 444mm)

Base (D2916A)

(349 x 392mm)

Upright (D2912A)

(706 x 394mm)

Right Side (D2913A)

(706 x 394mm)

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Shelf (D2919A)

(349 x 373mm)

Drawer Base (T161)

(299 x 330mm)

Modesty (D2917A)

(602 x 157mm)

Back (X725)

(626 x 373mm)

Plinth (D2918A)

(349 x 80mm)

Drawer Wrap (W161)

(943 x 95mm)

Drawer Front (D3072A)

(345 x 157mm)

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 2

Metal dowel (F901) x 8 Shelf stud (F110) x 4

Large locking nut (F900) x 6

Small locking nut (F3) x 2

40mm Screw (F910) x 10

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

R (F601)

L (F600)

F599

Drawer stops (F599) x 2 Runners (F600) x 1 and (F601) x 1

Nail (F51) x 12

Wedgefix (F639) x 2

Plastic Nail (F91) x 6

Handle (F930) x 1

25mm Screw (F95) x 2

+ 8 hidden pages