Argos Caspian - Double Pedestal Desk Mk2 ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 138cm
Depth - 44.5cm
Height - 72cm
Caspian - Double Pedestal Desk Mk2
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 13/11/12
Important - Please read these instructions fully before starting assembly
621/3561
621/3891
621/3554
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 31kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
3
6
7
9
8
10
11
12
13
14
1 2
Cupboard Left Side (D1199A)
(706 x 394mm)
Drawer Left Side (D1203A)
(706 x 394mm)
Cupboard Right Side (D1200A)
(706 x 394mm)
Top (D1198A)
(1377 x 444mm)
Drawer Right Side (D1204A)
(706 x 394mm)
Base (D1201A)
(349 x 378mm) x 2
Shelf (D1202A)
(349 x 373mm) x 2
Plinth (D0868A)
(349 x 80mm) x 2
Modesty (D0882A)
(614 x 157mm)
Door (D1258A)
(463 x 345mm)
Drawer Front (D0284A)
(345 x 157mm)
Back (X846)
(622 x 375mm) x 2
Drawer Wrap (W161)
(943 x 95mm)
Drawer Base (T161)
(299 x 330mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 10
C
D
Large locking nut (F900) x 8
E
Small locking nut (F3) x 2
F
G
40mm Screw (F910) x 16
H I
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Hinge plate (F523) x 2
M
L
Hinge (F522) x 2
K
Nail (F51) x 22
J
13mm Screw (F63) x 4
Handle (F923) x 2
19mm Screw (F461) x 4
O
M
9mm Screw (F74) x 2
N
9mm Screw (F73) x 4
Drawer runner (F1004) x 2
Shelf support (F121) x 8
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Electric drill (only use when drilling door)
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the drawer front and wrap
a: Screw 2 metal dowels
. into the holes shown on the back of the drawer front .
Note: Tighten metal dowels up fully against the panel.
b: Insert 2 small locking
nuts into the holes shown on the drawer wrap .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
B
10
a:
b:
F
11
Assemble the drawer
a: Place drawer base
into the narrow slot on the drawer wrap . Fold wrap around the base.
b: Turn drawer wrap
assembly over and push onto the back of the drawer front .
Note: Turn locking nuts clockwise to secure panels - more than 1/2 a turn.
12
12
11
10
F
10
11
11
11
B
B
F
a:
b:
B
F
11
F
F
Step 2
B
B
10
10
11
plain surface
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
5
Step 3
Attach handle
Attach the handle to the drawer front using 2 screws .
D
H
D
H
H
Step 4
Prepare the drawer left side
a: Place a runner on
the drawer left side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and use the 2nd hole from the back to fit the 2nd screw . .
c: Insert 2 large locking
nuts into the drawer left side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Fit 2 hinge plates onto the drawer left side , making sure that the slot is facing towards the finished front edge.
1
O
N
E
N
Finished
front edge
N
O
a:
b:
c:
Rebated
back edge
N
O
E
1
1
N
E
E
10
10
N
O
1
I
I
I
I
1
1
Important:
Only drill the 2 holes
shown circled and
make sure that you
drill straight at 90
to the surface of the
panel.
90 90
2.5mm then
5mm
Assembly Instructions
6
Step 5
Small piece of
waste wood
ONLY drill
these 2 holes
2
Finished front edge
Drill 2 holes in the drawer right side
Lay the drawer right side . down onto a smooth surface.
Important: Carefully choose which 2 holes you need to drill.
Check that the holes are in the same place as the diagrams.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any break­out.
Using the pilot holes drill through the 2 holes indicated opposite, using a 2.5mm drill bit.
Turn the panel over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill bit.
2
IMPORTANT
Carefully choose which 2 holes you need to drill
Finished
front edge
2
Assembly Instructions
7
Step 6
b:
c:
a:
Rebated
back edge
N
O
Finished
front edge
N
O
Prepare the drawer right side
a: Place a runner on
the drawer right side . Slide back the top of the runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and use the 2nd hole from the back to fit the 2nd screw . .
c: Insert 2 large locking
nuts into the drawer right side as shown.
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
2
O
N
N
E
2
N
O
2
2
2
N
E
E
E
Finished front edge
Finished front edge
Finished front edge
Assembly Instructions
8
Step 7
G
G
G
Finished
front edge
Finished
front edge
Join the drawer right side to a base
Position a base against the drawer right side as shown and secure with 2 screws .
3
2
G
A
A
10mm
A
7
Plain chipboard
surface
Step 8
Prepare a plinth
Tap 2 wooden dowels into a plinth as shown.
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Step 9
A
7
Fit the plinth
Push the plinth onto the drawer right side as shown and secure with screw .
7
2
G
plain
chipboard
surface
3
2
2
Plain chipboard
surface
7
Finished
front edge
Assembly Instructions
Step 10
Fit the drawer left side
Push the drawer left side . onto the assembly and secure with 3 screws .
G
1
Step 11
1
G
G
G
Important:
Only drill the 2 holes
shown circled and
make sure that you
drill straight at 90
to the surface of the
panel.
90 90
2.5mm then
5mm
Drill 2 holes in the cupboard left side
Lay the cupboard left side down onto a smooth surface.
Important: Carefully choose which 2 holes you need to drill.
Check that the holes are in the same place as the diagrams.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any break­out.
Using the pilot holes drill through the 2 holes indicated opposite, using a 2.5mm drill bit.
Turn the panel over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill bit.
4
IMPORTANT
Carefully choose which 2 holes you need to drill
Finished
front edge
ONLY drill
these 2 holes
Small piece of
waste wood
Finished
front edge
4
4
9
G
G
Finished
front edge
Assembly Instructions
10
Step 12
Step 13
Prepare the cupboard left side
Insert 2 large locking nuts into the cupboard left side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
E
4
Finished
front edge
4
E
E
Prepare the cupboard right side
Insert 2 large locking nuts into the cupboard right side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
E
Step 14
5
5
E
E
Finished
front edge
Finished
front edge
Join the cupboard right side to a base
Position a base against the cupboard right side as shown and secure with 2 screws .
3
5
G
plain
chipboard
surface
3
5
Finished
front edge
Assembly Instructions
11
Step 15
Fit the cupboard left side
Push the cupboard left side onto the assembly and secure with 3 screws .
G
4
Step 16
Fit the plinth
Push the plinth onto the cupboard right side . as shown and secure with screw .
Step 17
7
5
G
A
A
10mm
A
7
Plain chipboard
surface
Prepare a plinth
Tap 2 wooden dowels into a plinth as shown.
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
A
7
5
Plain chipboard
surface
7
G
G
G
G
4
Assembly Instructions
12
Step 18
Prepare the top
Screw 8 metal dowels into the top .
B
9
Finished
bottom edge
Drawer
runners
2
4
8
G
G
G
G
Fit the modesty
Fit the modesty between the cupboard left side and drawer right side using 4 screws .
Using 2 people, carefully stand the unit up.
8
4
2
G
Warning: The unit is heavy. Lift with care.
Step 19
Finished
front edge
B
B
B
B
B
B
B
B
9
y
Assembly Instructions
13
Step 20
Step 21
E
B
Warning: The unit is heavy. Lift with care.
9
Fit the top
Lower the top onto the assembly, making sure that it is pushed down flush with the top edge of the 4 side panels.
Use a screwdriver to tighten the 8 large locking nuts fitted to the side panels.
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Using 2 people, carefully lower the assembly onto its front edges again.
9
E
E
14
x
y
x
y
14
Fit the backs
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the
2 backs onto the unit, as shown.
Nail around the sides and bottom edges of the backs .
Stand the unit up for the next step.
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
14
K
14
Warning: The unit is heavy. Lift with care.
b:
K
Assembly Instructions
14
Step 22
Fit the shelf studs
For each of the 2 shelves , insert 4 shelf studs at the required height.
6
C
Step 23
Fit the shelves
Lower the 2 shelves down onto the shelf studs .
6
C
C
x 4
C
x 4
6
6
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
C
Small piece of
waste wood
Assembly Instructions
15
Step 24
Step 25
Prepare the door
Push fit the 2 hinges into the door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
90
L
L
13
L
J
Drill 2 handle holes in the door
Important: Please follow these instructions carefully.
Lay the door down onto a smooth surface.
Check that the hinges and holes are in the same place as the diagram.
Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.
Using the pilot hole in the rear face of the door, drill through the hole indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm hole that you have just drilled by drilling back through it with a 5mm drill.
13
L
J
J
L
J
J
13
ONLY drill
these 2 holes
DO NOT drill
these holes
13
IMPORTANT
Carefully choose which 2 holes you will need to drill
Assembly Instructions
16
Step 26
Fit the door
Note: The easiest way to attach the door is to fit the top hinge first, then align and fit the other hinge.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
L
L
L
I
I
I
L
I
13
a: b:
c: d:
I
L
I
I
B
I
L
L
L
A
L
I
B
Assembly Instructions
17
Step 27
Adjust the door if needed
a: Before adjusting the
door, use a spirit level to check the top (or base) of the unit is level, front­to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
18
Step 28
Fit the door handle
Attach a handle to the door using 2 screws .
13
H
D
Fit the drawer
Slide both the runners forward and locate the drawer wrap between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
M
M
2nd threaded
hole
O
M
Step 29
O
O
11
11
H
H
M
M
13
D
Assembly Instructions
ALR269319
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 30
Assembly is complete
Warning: The unit is heavy. Lift with care.
Loading...