Argos CAPELLA PACKAGE ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 38cm
Depth - 39cm
Height - 58.5cm
Capella - 3 Drawer Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 20/04/15
Important - Please read these instructions fully before starting assembly
395/8056
408/6192
424/5263
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 13kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
1
4
2 3
8
5
9
10
6 7
Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
Top (D1001A)
(349 x 370mm)
Drawer Front (D1003A)
(345 x 157mm) x 3
Back (X490-375)
(490 x 375mm)
Rail (D1002A)
(349 x 103mm) x 2
Drawer Base (T328-367)
(328 x 367mm) x 3
Drawer Back (W317-124)
(317 x 124mm) x 3
Left Side (D1006A)
(584 x 390mm)
Right Side (D1007A)
(584 x 390mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 14
D E
Large locking nut (F900) x 8
G H I
K
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 6
C
Nail (F51) x 12
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Drawer runner (F1004) x 6 Handle (F930) x 3
25mm Screw (F50) x 6 9mm Screw (F74) x 6 9mm Screw (F73) x 12
F
Knock-in Peg (F171) x 12
M
Plastic Nail (F91) x 4
L
Wedgefix (F639) x 6
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 3
x 3
x 3
x 3
B
B
E
E
E
E
6
7
Step 2
Prepare the 3 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
E
6
7
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
5
E
E
6 7
6
7
B
B
5
5
Assembly Instructions
5
Step 4
F
F
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
F
Attach the handles
Attach a handle to each of the drawer fronts . using screw .
Note: Do not overtighten the screw.
K
G
5
6 7
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
L
x 3
x 3
x 3
F
F
x 3
L
L
L
9
6
8
6
7
9
7
K
G
G
5
Profiled
front edge
Profiled
front edge
Profiled
front edge
Assembly Instructions
6
Step 8
Profiled
front edge
I
J
I
J
Prepare the left side
a: Place 3 runners on
the left side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 4 metal
dowels into the left side .
a:
b:
c:
1
I
B
1
1
1
1
1
B
B
B
B
I
J
I
I
I
I
J
I
J
Assembly Instructions
7
Step 9
Prepare the right side
a: Place 3 runners on
the right side . Slide back the top of the runner and use the 1st hole from the front to fit the 1st screw .
b: Slide the runner back
the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 4 metal
dowels into the right side .
Profiled
front edge
I
J
I
J
2
I
B
2
2
a:
b:
c:
I
J
I
I
I
I
J
I
J
Profiled
front edge
Profiled
front edge
Profiled
front edge
B
B
B
B
2
2
2
A
Finished
front edge
Finished
front edge
A
A
Assembly Instructions
8
Step 10
Prepare the top
Tap 4 wooden dowels into the top as shown.
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the top as shown.
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
10mm
A
A
3
3
D
Fit the top to the right side
Push the top onto the right side as shown.
Use a screwdriver to tighten the 2 large locking nuts fitted to the top .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 11
3
2
D
D
D
D
D
D
A
A
Finished
front edge
3
B
D
3
2
Prepare the 2 rails
Tap 2 wooden dowels into each of the rails .
Insert 2 large locking nuts into each of the rails .
A
4
4
x 2
Step 12
D
D
A
D
4
Assembly Instructions
9
Step 13
Fit the 2 rails
Push the rails onto the right side as shown.
Use a screwdriver to tighten the 2 large locking nuts fitted to the rails .
4
2
D
4
Support this rail until the left side has been fitted in the next step.
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and the rails .
D
1
3
4
Step 14
4
2
4
4
4
1
3
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
M
1
2
M
M
M
M
Step 15
1
2
Assembly Instructions
10
Step 16
Step 17
b:
C
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
10
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
yy
yy
xx
10
xx
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
H
J
J
H
2nd threaded
hole
J
H
6 7
H
H
6
7
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3161
Step 18
Assembly is complete
Loading...