Page 1
BOURNE CONTEMPORARY OAK 5FT FO
Assembly Instructions
- Please keep for future reference
3576995
Dimensions
Width - 158.7cm
Depth - 208.4cm
Height -100.3cm
Important
If you need help or have damaged or missing parts, call the
14-3B-636_03
– Please read these instructions fully before starting assembly
Customer Helpline:
03456 400 800
Issue 2 - 14/11/5
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (- in the same
room)as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set
on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
1
Page 3
If you have damaged or missing commponents,
Components - Parts
call the
Please check you have all the panels listed below
1
Headboard x 1
(158,7 x 100,3cm)
2
Customer Helpline:
03456 400 800
Footboard x 1
(158,7 x 41,0cm)
3
Side rail x 2
(197 x 20cm)
4
Central rail x 1
(198,4 x 6,5cm)
5
Slat x 38
(73,5 x 5,3cm)
2
Page 4
Components - Fittings
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly. In some cases more fittings may
be supplied than are required.
A1
Sideboard hanger A x4
D1
25mm Screw x4
G1
B1
30mm Screw x16
E1
Central rail hanger B x2
H1
C1
Central rail hanger A x2
F1
11mm Screw x8
I1
Slat housing x72
J1
Sideboard hanger B left x2
Tools required
Phillips screwdriver
(medium & large)
Support leg x1 Leg extension x1
K1
Sideboard hanger B right x2
Ruler - Use this ruler to help correctly identify the screws
M1
16mm Screw x16
Hammer
Ruler/tape
measure
The screws length is measured from the head to the point (30mm screw shown)
3
Page 5
Assembly Instructions
Step 1
Attaching the central
rail hangers B
Fit central rail hanger B
E1
e to headboard and
footboard with screws
F1 .
F1
2
1
2
E1
Step 2
Attaching the sideboard
hangers A
1
1
E1
E1
F1
Use lower holes
1
2
E1
2
Use upper holes
F1
E1
F1
1
2
A1
B1
Position sideboard
hanger A onto the
drilled holes of the
headboard and
footboard .
Fix through holes shown
using screws .
A1
1
2
B1
A1
1
B1
A1
2
B1
4
Page 6
Assembly Instructions
Step 3
Attaching sideboard
hangers B
Position right / left
sideboard hanger B
on to the drilled holes of
the side rails .
Fix it using the screws .
K1
J1
3
M1
M1
J1
M1
3
J1
3
M1
K1
M1
3
K1
5
Page 7
Assembly Instructions
Step 4
Bed frame assembly
Hook the fitting on the
side rails into the
sideboard hanger A
on the footboard and
headboard .
3
A1
2
1
A1
3
1
A1
3
1
2
A1
3
2
A1
Step 5
Central rail setup
Fit the central rail hanger A
c to central rail and fix
C1
with screws .
4
D1
D1
D1
C1
C1
4
D1
C1
6
Page 8
Assembly Instructions
Step 6
Attaching the support
leg
Join both parts of the
support leg together.
Join the support leg with
leg extension and insert
into the hole in the central
4
rail .
H1
H1
I1
Step 7
Central rail inserting
Hook the central rail
hanger A on the central
rail into the central rail B
c on the footboard and
E1
headboard .
C1
4
2
1
I1
H1
H1
4
I1
H1
E1
E1
E1
C1
C1
1
4
2
4
C1
4
4
77
Page 9
Assembly Instructions
Step 8
Adjusting the support
leg
The support leg must
stand firmly on the floor,
so adjust the height of the
support leg accordingly.
H1
H1
H1
H1
G1
Step 9
Slats installation
Put the housing on the
both end of the slat ,
than stick it into holes in
side and central rail .
Use a hammer gently if
needed.
Repeat for the rest of slats.
G1
5
4
G1
5
3
G1
4
5
G1
4
8
Page 10
Assembly Instructions
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Home Retail Group Plc, 489 - 499 Avebury Boulevard, Milton Keynes, MK9 2NW
9
Loading...