Page 1
Sophia 3 Drawer Bedside
Assembly Instructions - Please keep for future reference
499/5348
501/5320
501/1496
Dimensions
Width - 40cm
Depth - 41.5cm
Height - 67cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts,call the Customer Helpline:03456 400800.
For further assistance please visit http://www.argos-support.co.uk/
Issue 1 - 12/05/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
·Check you have all the
components and tools listed on
pages 2 and 3.
·Remove all fittings from the
plastic bags and separate them
into their groups.
·During assembly keep children
and animals away from the work
area due to possible risk of injury
and small parts could choke if
swallowed.
Care and maintenance
·Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
·Do not stand or put weight on
the product, this could cause
damage.
·Assemble the item as close to
its final position (in the same
room) as possible.
·Assemble on a soft level
surface to avoid damaging the
unit or your floor.
·Parts of the assembly will be
easier with 2 people.
·From time to time check that
there are no loose screws on
this unit.
·To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torgue
setting.
·This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
·Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
·Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
If you have damaged or missing componets, call the
Components - Panels
Customer Helpline:03456 400800.For further
assistance please visit http://www.argos-support.co.uk/
Please check you have all the panels listed below
Left Side × 1 (43.4 × 38.6cm) Right Side × 1 (43.4 × 38.6cm)
Top × 1 (40 × 41.5cm)
1
Base frame × 1 (40 × 41.5cm)
4
Drawer side, left × 3 (30 × 9.5cm)
7 9
2
Leg × 4 (20 × 4.5cm)
5
8
Drawer side, right × 3 (30 × 9.5cm)
3
6
Drawer front × 3 (25 × 14cm)
Drawer back × 3 (20.5 × 9.2cm)
10
Drawer base × 3 (21.6 × 29.9cm)
Back panel × 1 (26.6 × 44.5cm)
11
2
Page 4
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Wooden dowel × 8
Ø3.5×25mm
Screw × 13
G
J K
M N
P
Allen key × 1
300mm Runner,
outside left × 3
300mm Runner,
inside right × 3
washer× 4
B
Large locking pin × 12
Small locking pin × 12
H I
Handle × 3
300mm Runner,
outside right × 3
Ø3.5×15mm
Screw × 42
Q
Ø6×40mm
Screw × 4
C
Large locking
nut × 12
FED
Small locking nut
× 12
D5/32''×7/8'' Screw × 3
L
300mm Runner,
inside left × 3
O
washer × 5
R
Wall strap
× 1
S
Back panel
support × 1
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Ruler - Use this ruler to help correctly identify the screws
0 101520253035404550556065707580859095100
5
105
Rubber
mallet
110115120125130135140145150155160165170
3
Page 5
Assembly Instructions
Step 1
Fitting dowels
a:Insert Wooden dowels
A
into Left side and
Right side .
2
3
b: Fix Runner Outside
K
Right onto Left side
by using Screws .
Fix Runner Outside
J
Left onto Right side
3
by using Screws .
N
K
2
N
K
N
N
J
×12
N
4
Page 6
Assembly Instructions
Step 2
Fitting locking pins
Insert Large locking Pin
into Top .
1
Note: Insert locking pin
as shown.
Do not over tighten.
5
4
O
Q
P
G
B
B
Fitting locking pins
Fitting Large Locking
pins to Base Fram .
B
5
4
4
Page 7
Assembly Instructions
Step 5
Attach the Sides to Base
frame .
Attach Left Side to
Base Fram and fixing
by Large Locking Nut
.
Repeat this step to
attach Right Side to
Base Frame .
13
B
C
2
4
3
4
1 2 3
C
B
3
2
Step 6
Insert back panel
Slip the Back panel to
the groves on the Sides.
11
11
6
Page 8
Assembly Instructions
Step 7
Attaching Top
Attach Top to the unit.
Insert Large Locking
C
Nuts where shown and
use a screw driver to turn
locking nuts clockwise to
lock.
1
1 2 3
C
B
1
Step 8
Drawer assembly
a: Insert 4 Small locking
E
pin into holes shown
on back of Drawer front
.
6
Note: Insert Locking pin
as far as shown.
Do not over tighten.
b:Attach Drawer sides
8
and to draw front .
Insert 4 Small locking
F
nuts into Sides.
Use a screwdriver to turn
locking nuts clockwise
to lock.
F
6
7
7
Page 9
Assembly Instructions
Step 9
c: Slip Drawer base
into grooves.
d: Fix Drawer back
onto sides by using 4
Screws .
10
9
e: Fix Handle by
using Screw .
f: Fix Runners and
onto the underside of
Drawer sides by using 6
Screws .
Repeat a - f to finish
another 2 drawers.
H
I
M
N
L
8
Page 10
Assembly Instructions
Step 10
Fixing Wall strap
Fix Wall Strap by Back
panel support Washer
and Screw .
O
R
S
D
Step 11
Insert drawers
Carefully put in drawers
to the unit.
If you need help or have damaged or missing parts,call the Customer Helpline:
03456 400800 Retailer:Argos
Address: 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes
Bucks, MK9,2NW
For further assistance please visit http://www.argos-support.co.uk/
9
Page 11
Assembly Instructions
Step 12
Fixing to wall
The Bedside table should
be fixed to a wall.
Move Bedside table into
position.
Mark fixing hole on wall
and remove Bedside
table.
Drill hole and insert
wall plug.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Reposition Bedside table
and fix wall strap using
washer and screw.
Assembly is finished.
Note: wall plugs are not
supplied.
The correct type of fixing must
be used for your wall, seek
professional advice in doubt.
If you need help or have damaged or missing parts,call the Customer Helpline:
03456 400800 Retailer:Argos
Address: 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes
Bucks, MK9,2NW
For further assistance please visit http://www.argos-support.co.uk/
10
Page 12
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect xings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well tted and are a tight t in the
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist tting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
plasterboard. The hammer xing allows
it to be xed to the wall rather than the
plasterboard. Always check the xing
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when tting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...