Argos Asha - Cabin Bed ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assembly

IMPORTANT !

KEEP THESE ASSEMBLY INSTRUCTIONS

FOR FUTURE REFERENCE

WARNING!

NOT SUITABLE FOR CHILDREN

UNDER 4 YEARS OF AGE .

This product conforms to

BS 8509: 2008+A1: 2011

Asha - Cabin Bed

411/9454

427/8632

Width - 195.5cm

Depth - 96cm

Height - 42cm

Issue 2 - 29/09/15

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• The recommended mattress size is 900mm x 1900mm.

• Minimum mattress height of 200mm to be used.

• WARNING! Do not place this child’s bed near heat

sources, windows and other furniture.

• WARNING! Do not use this child’s bed if any part is

broken, torn or missing.

• WARNING! Not suitable for children under 4 years old.

• WARNING! Children are likely to play, bounce, jump and

climb on beds, therefore the child’s bed should not be placed too close to other furniture or windows, blinds or cords, curtain pulls or other strings or cords and should be placed either tight to any wall or have a gap of 300mm between the wall and the side of the bed.

• This unit is not designed to be dismantled for storage or

transportation.

1

IMPORTANT! On a regular basis please check that the screws and fittings have not become loose as this could present a potential choke hazard.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 47kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

2

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

3

1

End Panel (D3112)

(95.6 x 41.8cm) x 2

Door (D3115)

(33.5 x 31.1cm) x 2

Lower Middle Plinth (D3118)

(63 x 7.8cm) x 2

Middle Matress Base (D3117)

(64.5 x 95.2cm)

Side Rail (D3116)

(96 x 4.5cm) x 4

Back Brace (D3113)

(63 x 20cm) x 3

Divider (D3114)

(35.6 x 94.8cm) x 2

LH Side Plinth (D3119)

(63 x 7.8cm) x 2

RH Side Plinth (D3123)

(63 x 7.8cm) x 2

End Mattress Base (D3120)

(63.75 x 95.2cm) x 2

Bed Base (X788-630)

(78.8 x 63cm) x 3

2

3 4

8

6

5

7

9

10

11

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

4

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G

M

P

C

N

H J

L

O

Large locking nut (F900) x 28

Metal dowel (F901) x 4

Wooden dowel (F22) x 10

Large wooden dowel (F40) x 12

Double metal dowel (F566) x 12

K

Allen Key (F36) x 1

50mm Screw (F49) x 12

Shelf support (F121) x 2

I

13mm Screw (F63) x 8

Mini block (F25) x 4

13mm Screw (F79) x 24

Hinge plate

(F523) x 4

Hinge (F522) x 4

Handle (F273) x 2

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Bracket (F945) x 12

18mm Screw (F411) x 4

Finished

top edge

Finished

top edge

C

Assembly Instructions

5

Step 1

Step 2

x 2

Prepare the 2 end panels

Screw 2 metal dowels into each od the 2 end panels .

Note: Tighten the metal dowels up fully against the panels.

A

1

A

1

B

Prepare 1 of the back brace panels

Insert 4 large locking nuts into a back brace .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap a wooden dowel into the back brace .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Step 3

B

10mm

42mm

C

B

8

C

8

B

A

Fit the back brace to an end panel

Push the back brace onto a end panel .

Use a screwdriver to tighten the 2 large locking nuts fitted to the back brace .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

1

8

B

8

1

8

42mm

Top

edge

Top

edge

C

Assembly Instructions

6

Step 4

Prepare the 2 left plinths

Insert a large locking nut into each of the 2 left plinths .

Tap a wooden dowel into each of the 2 left plinths .

Step 5

B

C

Finished

front edge

Finished

front edge

B

5

C

5

x 2

7

Prepare the 2 right plinths

Insert a large locking nut into each of the 2 right plinths .

Tap a wooden dowel into each of the 2 right plinths .

B

7

C

7

Prepare 1 of the divider panels

Fit 2 hinge plates onto a divider , making sure that the slot is facing towards the finished front edge.

Gently tap 2 mini blocks . into the divider , orientated as shown.

O

L

O

Step 6

L

O

2

L

2

Note: The right plinths have identification marks.

Finished

front edge

The right plinth

will have an

Identification mark

Finished

top edge

Assembly Instructions

7

Step 7

Fit a right plinth and a left plinth

Attach a right plinth to the end panel using 1 screw and tighten it using the allen key .

Attach a left plinth to the end panel using 1 screw and tighten it using the allen key .

1

7

F

K

1

5

F

K

7

5

1

Finished

front edge

Note: Support the left plinth and the back brace until the divider has been fitted in the next step.

E

Step 8

Fit the divider

Tap 3 large wooden dowels through the divider and into the left plinth , the right plinth and the back brace until they ‘’bottom out’’.

Step 9

Fit the double metal dowels

Tap 4 double metal dowels through the divider and into the left plinth , the right plinth and the back brace until they ‘’bottom out’’.

E

2

5 7

8

D

2

5 7

8

2

5

7

8

2

5

7

8

D

F

K