Argos Arvika - 3 Drawer Bedside ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 37cm

Depth - 39.5cm

Height - 65cm

Arvika - 3 Drawer Bedside

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 11/11/14

Important - Please read these instructions fully before starting assembly

355/7794

359/8430

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 14.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Components - Panels

Please check you have all the panels listed below

2

1

2 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (DF1407)

(370 x 394mm)

Drawer Front (DF1408)

(332 x 161mm) x 3

Left Side (DF1895)

(495 x 393mm)

Base (DF1962)

(370 x 394mm)

Drawer Base (T299-347)

(299 x 347mm) x 3

Right Side (DF1896)

(495 x 393mm)

Drawer Back (W288-124)

(288 x 124mm) x 3

Left Drawer Side (W350-124LH)

(350 x 124mm) x 3

Right Drawer Side (W350-124RH)

(350 x 124mm) x 3

4

5 6

9

10

7 8

Back (X520-364)

(520 x 364mm)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G H I

L

O

Small locking nut (F3) x 6

C

Nail (F51) x 12

40mm Screw (F910) x 4

J K

N

Knock-in Peg (F171GY) x 12

Large locking nut (F900) x 4

Metal dowel (F901) x 10

Wooden dowel (F22) x 8

M

Wedgefix (F639) x 6

19mm Screw (F461) x 6

13mm Screw (F79) x 16

13mm Screw (F63) x 18

9mm Screw (F73) x 18

Handle (F336) x 3 Leg (F343) x 4

Leg Bracket

(F333) x 4

P

R Runner (F160) x 3

b

L Runner (F161) x 3

P

c

L Runner (F159) x 3

P

a

R Runner (F162) x 3

P

d

350mm long

5

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

A

B

A

C

7

8

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

A

5

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

C

7

8

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

7 8

5

C

7 8

A

5

8

7

5

Assembly Instructions

5

Step 4

F

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

9

7 8

5

6

7 8

9

6

F

7 8

x 3

F

9

7

8

9

6

7

8

H

Attach the handles

Attach a handle to each of the drawer fronts . using screws .

H

5

M

5

M

P d

R

Assembly Instructions

6

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

L

x 3

L

Fit the runners

Fit a runner , marked with ‘R’, to the bottom edge of the right drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the left drawer side using the same method.

7

P d

8

5

J

P c

Step 8

J

L

P c

L

J

Runners must be

pushed up against

the drawer front

5

8

7

Finished

front edge

Finished

front edge

D

Assembly Instructions

7

Step 9

P a

K K

1st screw

2nd screw

K

3rd screw

Finished

front edge

P a

J

Finished

front edge

b:

a:

Prepare the left side

a: Fit 3 runners to

the left side .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 4 wooden dowels into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

P a

1

K

J

B

1

D

1

P a

K

P a

K

P a

K

P a

K

J

10mm

D

B

D

B

1

D

Assembly Instructions

8

Step 10

Prepare the right side

a: Fit 3 runners to

the right side .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Insert 2 large locking nuts into the right side .

Tap 4 wooden dowels into the right side .

P b

2

K

J

B

2

D

2

P b

J

P b

KK

1st screw

2nd screw

K

3rd screw

J

K

P b

K

P b

K

P b

K

B

D

2

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Assembly Instructions

9

Step 11

Prepare the top

Screw 4 metal dowels into the top .

Note: The top panel has been finished on both surfaces. The base panel has 1 chipboard suface.

A

3

A

3

Finished

front edge

Fit the right side to the top

Push the right side onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

2

B

A

B

Step 12

2

Fit the left side

Push the left side onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the left side .

3

1

B

Step 13

1

3

2

1

Assembly Instructions

10

Step 14

1

2

4

Finished

front edge

1

2

4

Fit the base

Attach the base the the sides and using the 4 screws .

4

1 2

G

plain

chipboard

surface

O

Step 15

Note: The raised part of the leg bracket must point towards the centre of the panel.

Fit the leg brackets to the base

a: Screw each leg

bracket . to the base using 2 screws into the mark holes.

b: Then use another 2

screws into the other 2 holes.

4

O

I

O

I

Assembly Instructions

11

Step 16

Fit the legs

Screw the legs into the leg brackets .

Carefully stand the unit up for the next step.

Step 17

yy

xx

b:

E

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

10

E

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

10

N

O

xx

N

Assembly Instructions

12

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 18

Fit the drawers

Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.

Assembly is complete

Side

panel

Drawer

ALR3112

MADE IN

BRITAIN

Dimensions

Width - 72cm

Depth - 39.5cm

Height - 106cm

Arvika - 4+2 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 17/12/14

Important - Please read these instructions fully before starting assembly

346/4966

343/2857

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 33.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance kit supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (DF914)

(716 X 394mm)

Base (DF1963)

(716 X 394mm)

Large Drawer Front (DF1442)

(678 x 245mm)

Large Drawer Back (W633-165)

(633 x 165mm)

Large Left Drawer Side (W350-165LH)

(350 x 165mm)

Large Right Drawer Side (W350-165RH)

(350 x 165mm)

Mid Drawer Front (DF915)

(678 x 161mm) x 3

Large Drawer Base (T644-347)

(644 x 347mm) x 4

Mid Drawer Back (W633-124)

(633 x 124mm) x 3

1

2

33

Small Left Drawer Side (W350-124LH)

(350 x 124mm) x 5

Small Right Drawer Side (W350-124RH)

(350 x 124mm) x 5

12

13

14

10

11

4

15

16

17

18

Top Left Drawer Front (DF1883)

(337.5 x 161mm)

Top Drawer Base (T295-347)

(295 x 347mm) x 2

Top Drawer Back (W284-124)

(284 x 124mm) x 2

Left Side (DF1881)

(907 x 393mm)

Right Side (DF1882)

(907 x 393mm)

Divider (DF1885)

(158 x 363mm)

Back (X933-710)

(933 x 710mm)

5

Top Right Drawer Front (DF1964)

(337.5 x 161mm)

6 7

8 9

19

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G H I

L

O

Small locking nut (F3) x 12

C

Nail (F51) x 20

40mm Screw (F910) x 4

J K

N

Knock-in Peg (F171GY) x 24

Large locking nut (F900) x 6

Metal dowel (F901) x 18

Wooden dowel (F22) x 10

M

Wedgefix (F639) x 20

19mm Screw (F461) x 12

13mm Screw (F79) x 16

13mm Screw (F63) x 36

9mm Screw (F73) x 36

Handle (F336) x 6 Leg (F343) x 4

Leg Bracket

(F333) x 4

P

R Runner (F160) x 6

b

L Runner (F161) x 6

P

c

L Runner (F159) x 6

P

a

R Runner (F162) x 6

P

d

350mm long

Q

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 2 x 2

x 2

A

B

A

C

10

11

Step 2

Prepare the 2 top drawer fronts

Screw 2 metal dowels into each of the top drawer fronts and .

Note: Tighten the metal dowels up fully against the panels.

A

6 7

Prepare 2 pair of small drawer sides

Insert a small locking nut into the hole shown on the small left drawer side and the small right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

C

10

11

Attach the small drawer sides to the top drawer fronts

Push the small left drawer sides . and small right drawer sides . onto the back of the top drawer fronts and . .

Turn the small locking nuts on the small left drawer side and small right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

10

7

11

6

C

10

11

10

A

Note: The top right drawer front has a small identification hole.

6

7

6 7

Assembly Instructions

5

Step 4

F

Fit the top drawer base

Slide the top drawer base down the grooves in the small drawer sides and and down into the groove in the top drawer fronts and .

Step 5

Fit the top drawer back

Fit the top drawer back . between the small drawer sides and . Make sure that the top drawer base fits into the groove in the top drawer back .

Hold the top drawer back in position and tap the knock-in pegs through the holes in the small drawer sides and .

Step 6

9

10

11

6 7

8

10 11

9

8

F

10

11

x 2

F

9

10

11

8

10

11

Attach the handles

Attach a handle to each of the top drawer fronts and using screws .

H

6 7

M

6 7

9

6 7

H

M

P d

R

Assembly Instructions

6

Step 7

Fit the wedgefixes

Turn the top drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

L

x 2

L

Fit the runners

Fit a runner , marked with ‘R’, to the bottom edge of the small right drawer side , as shown, making sure that it is pushed up against the back of the top drawer front and . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the small left drawer side using the same method.

10

P d

11

6 7

J

P c

Step 8

L

P c

L

Runners must be

pushed up against

the drawer front

11

10

L

J

6 7

12

Assembly Instructions

7

Step 9

x 3

A

B

A

C

10

11

Step 10

Prepare the 3 mid drawer fronts

Screw 2 metal dowels into each of the mid drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

A

12

Prepare 3 pair of small drawer sides

Insert a small locking nut into the hole shown on the small left drawer side and the small right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 11

C

10

11

Attach the small drawer sides to the mid drawer fronts

Push the small left drawer sides . and small right drawer sides . onto the back of the mid drawer fronts .

Turn the small locking nuts on the small left drawer side and small right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

10

11

12

C

10

11

10

12

A

12

Assembly Instructions

8

Step 12

F

Fit the large drawer base

Slide the large drawer base down the grooves in the small drawer sides and and down into the groove in the mid drawer front .

Step 13

Fit the mid drawer back

Fit the mid drawer back . between the small drawer sides and . Make sure that the large drawer base fits into the groove in the mid drawer back .

Hold the mid drawer back in position and tap the knock-in pegs through the holes in the small drawer sides and .

Step 14

14

10 11

12

13

10 11

14

13

F

10

11

x 3

F

14

10

11

14

13

10

11

Attach the handles

Attach a handle to each of the mid drawer fronts using screws .

H

12

M

12

H

M

Assembly Instructions

9

Step 15

P d

R

Fit the wedgefixes

Turn the mid drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

L

x 3

L

Fit the runners

Fit a runner , marked with ‘R’, to the bottom edge of the small right drawer side , as shown, making sure that it is pushed up against the back of the mid drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the small left drawer side using the same method.

10

P d

11

12

J

P c

Step 16

L

P c

L

Runners must be

pushed up against

the drawer front

11

10

L

12

J

15

Assembly Instructions

10

Step 17

A

B

A

C

17

18

Step 18

Prepare the large drawer front

Screw 2 metal dowels into the large drawer front .

Note: Tighten the metal dowels up fully against the panels.

A

15

Prepare the large drawer sides

Insert a small locking nut into the hole shown on the large left drawer side and the large right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 19

C

17

18

Attach the large drawer sides to the large drawer front

Push the large left drawer sides . and large right drawer sides . onto the back of the large drawer front .

Turn the small locking nuts on the large left drawer side and large right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

17

18

15

C

17

18

17

15

A

15

Assembly Instructions

11

Step 20

F

13

18

Fit the large drawer base

Slide the large drawer base down the grooves in the large drawer sides and and down into the groove in the large drawer front .

Step 21

Step 22

14

17

18

15

14

Attach the handle

Attach a handle to the large drawer front using screws .

H

15

M

17

18

17

Fit the large drawer back

Fit the large drawer back . between the large drawer sides and . Make sure that the large drawer base fits into the groove in the large drawer back .

Hold the large drawer back in position and tap the knock-in pegs through the holes in the large drawer sides and .

16

17 18

14

16

F

17

18

F

14

16

15

H

M

Assembly Instructions

12

Step 23

P d

R

Fit the wedgefixes

Turn the large drawer assembly over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

L

Fit the runners

Fit a runner , marked with ‘R’, to the bottom edge of the large right drawer side , as shown, making sure that it is pushed up against the back of the large drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit runner , marked ‘L’, to the bottom edge of the large left drawer side using the same method.

17

P d

18

15

J

P c

Step 24

L

P c

L

Runners must be

pushed up against

the drawer front

18

17

L

15

J

Finished

front edge

Finished

front edge

Assembly Instructions

13

Step 25

D

P a

K K

1st screw

2nd screw

K

3rd screw

Finished

front edge

P a

J

Finished

front edge

b:

a:

Prepare the left side

a: Fit 5 runners to

the left side .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 4 wooden dowels into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

P a

1

K

J

B

1

D

1

P a

10mm

D

B

K

P a

K

P a

K

P a

K

P a

K

P a

K

1

J

D

B

D

Assembly Instructions

14

Step 26

Prepare the right side

a: Fit 5 runners to

the right side .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Insert 2 large locking nuts into the right side .

Tap 4 wooden dowels into the right side .

P b

2

K

J

B

2

D

2

P b

J

P b

KK

1st screw

2nd screw

K

3rd screw

K

P b

K

P b

K

P b

K

P b

K

Finished

front edge

Finished

front edge

2

J

D

B

K

P b

K

b:

a:

Assembly Instructions

15

Step 27

Finished

front edge

Finished

front edge

K

P a

K

D

J

B

D

K

P b

K

Finished

front edge

Finished

front edge

J

Turn the divider over

b:a:

d:c:

Prepare the divider

a: Fit a runner to

the divider .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

Insert 2 large locking nuts into the divider . .

Tap 4 wooden dowels into the divider .

Turn the divider over

c: Fit a runner to

the divider .

The 1st screw uses the 1st hole in from the front of the runners.

The 2nd and 3rd screws . use the holes that line up with the other panel holes.

b: Fit a screw into

the 2nd hole in at the top of the runners .

P a

5

K

J

B

5

D

5

P a

P b

5

K

J

P b

P a

K K

1st screw

2nd screw

K

3rd screw

Finished

front edge

P a

J

Finished

front edge

P b

J

P b

KK

1st screw

2nd screw

K

3rd screw

5 5

Note: Due to the manufacturing process, the 2 holes for the large locking nut can be on either surface of the panel.

Assembly Instructions

16

Step 28

Finished

front edge

Finished

front edge

Finished

front edge

Fit the sides to the top

Push the left side and right side onto the top .

Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and right side .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

1

3

B

A

B

Step 30

1

2

3

2

1

Prepare the top

Screw 6 metal dowels into the top .

Note: The top panel has been finished on both surfaces. The base panel only has 1 finished suface.

A

3

A

Finished

front edge

3

Fit the divider to the top

Push divider down onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .

3

5

B

Step 29

3

5

Finished

front edge

A

Remember: The large locking nuts can be on either surface of the divider.

Assembly Instructions

17

Step 31

Step 32

4

2

1

Note: The raised part of the leg bracket must point towards the centre of the panel.

Fit the base

Attach the base the the sides and using the 4 screws .

4

1 2

G

Finished

front edge

G

4

2

1

plain

chipboard

surface

Fit the leg brackets to the base

a: Screw each leg

bracket . to the base using 2 screws into the mark holes.

b: Then use another 2

screws into the other 2 holes.

4

O

I

O

I

yy

1

yy

xx

Assembly Instructions

18

Step 33

b:

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

19

E

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

19

E

19

1

Fit the legs

Screw the legs into the leg brackets .

Carefully stand the unit up for the next step.

Step 34

N

O

N

Warning: The unit is heavy. Lift with care.

Assembly Instructions

19

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR3114

Step 35

Attach the

strap to the unit

Attach the

strap to the wall

Wall fixing

(not supplied)

Washer

Strap

Q

Example

Screw

(not supplied)

Washer

Screw

UNIT

Note: The top right drawer front has a small identification hole (refer back to step 1).

Fit the overbalance protector and drawers

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.

Wall fixings are not supplied as they will need to suit the wall type.

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.

Q

Warning: The unit is heavy. Lift with care.

Side

panel

Drawer

MADE IN

BRITAIN

Dimensions

Width - 123cm

Arvika - 3 Door Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 16/12/14

Important - Please read these instructions fully before starting assembly

335/9789

346/6531

Depth - 49.5cm

Height - 186.5cm

Components - Panels

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 83.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• We do not

recommend the

use of power

drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance kit supplied.

• Dispose of all packaging carefully and responsibly.

1

2 3

Left Side (DF917)

(1791 x 494mm)

Right Side (DF1893)

(1791 x 494mm)

Divider (DF1892)

(1791 x 464mm)

Please check you have all the panels listed on pages 1 and 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Components - Panels

2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Horizontal (DF1420)

(797 x 464mm)

Shelf (DF1894)

(382 x 463mm) x 3

Top (DF1891)

(1226 x 495mm)

Base (DF1965)

(1226 x 495mm)

7

8

4 5

Hanging Rail (FHR791)

(791mm long)

6

9 10

Right Door (DF3010)

(1785 x 394mm)

Left Door (DF920)

(1785 x 394mm)

Mirror Door (DF3011)

(1785 x 394mm)

Mirror - SG27 1755 x 388mm Safety Back SAR

11

Small Back (X1817-401)

(1817 x 401mm)

Large Back (X1817-816)

(1817 x 816mm)

12 13

Please check you have all the panels listed on pages 1 and 2

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D

H I

L

C

Nail (F51) x 40

G

40mm Screw (F910) x 17

J K

N

Large locking nut (F900) x 4

Metal dowel (F901) x 4 Wooden dowel (F22) x 16

M

O

19mm Screw (F461) x 4

13mm Screw (F63) x 22

Handle (F336) x 2

Leg (F334) x 5

Rail Holder (F891) x 2

P

Hinge plate (F523) x 9

Hinge (F522) x 9

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

Shelf stud (F110) x 12

E

F

Nail screw (F277) x 6

Back holder (F276) x 6

* These can also be round

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

mm

10

20

30

40

50

60

70

80

90

100

mm

10

20

30

40

50

60

70

80

90

100

C

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Finished

front edge

P

A

Prepare the divider

Screw 2 metal dowels into the divider .

Tap 4 wooden dowels into the divider .

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the divider . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Fit 3 hinge plates onto the divider , making sure that the slot is facing towards the finished front edge.

K

J

3

A

P

3

C

10mm

C

J

K

J

K

J

C

3

C

B

C

B

Prepare the horizontal

Insert 4 large locking nuts into the horizontal .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Tap 4 wooden dowels into the horizontal .

B

C

4

Step 2

Finished

front edge

4

C

Finished

front edge

P

Finished

front edge

Assembly Instructions

5

Step 3

Step 4

Finished

front edge

5

Fit the horizontal to the divider

Push the horizontal onto the divider .

Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

4

B

4

A

B

P

A

J

K

J

C

A

Prepare the left side

Screw 2 metal dowels into the left side .

Tap 4 wooden dowels into the left side .

To fit the rail holder , screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

K

J

1

A

P

1

C

1

3

G

Finished

front edge

Assembly Instructions

6

Step 5

Fit the left side

Push the left side onto the horizontal .

Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

4

1

B

G

4

1

Finished

front edge

G

Fit the top

Attach the top to the left side and divider using 4 screws .

G

7

1

3

Note: The top panel has been finished on both surfaces. The base panel only has 1 finished suface.

Step 6

7

3

G

C

Assembly Instructions

7

Step 7

Finished

front edge

P

C

Prepare the right side

Tap 4 wooden dowels into the right side .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

P

C

2

Fit the right side

Attach the right side to the top using 2 screws .

G

2

7

Step 8

2

7

Assembly Instructions

8

Step 9

Step 10

Fit the feet

Attach the 5 feet to the base using 5 screws .

N

G

8

Finished

front edge

2

Fit the base

Attach the base to the left side , right side and upright using 6 screws .

G

8

1

2 3

G

1

3

Finished

front edge

N

8

plain

chipboard

surface

8

G

yy

xx

yy

Assembly Instructions

9

Step 11

Fit the back panels

a: Square up the unit by

making sure that measurement x:x equals

y:y.

Place the small back and large back down, onto the unit as shown.

Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the divider’s back edge.

b: Nail around the

outside edges of the 2 backs.

Note: Do not nail where the 2 backs meet and nails should be spaced about 150mm apart.

c: Push the 6 nail

screws through the 6 back holders and tap them down between the small back and large back and into the back edge of the divider . .

Keep tapping the nail screws in until the back holders dig into the small and large back.

Carefully stand the unit up for the next step.

12

13

D

E

F

12

13

3

E

F

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

Note: If ever you need to take the backs off to dismantle the unit, the nail screws can be taken out using a screwdriver.

E

F

xx

c:

E

F

12

13

F

FE

+

Note: These can also be round

b:

D

12

13

Warning: The unit is heavy. Lift with care.

Assembly Instructions

10

Step 12

I

x 4

I

x 4

I

x 4

5

Fit the shelves

For each of the 3 shelves , insert 4 shelf studs .

Lower the 3 shelves down onto the shelf studs .

I

5

I

5

6

K

Fit the hanging rail

Push the hanging rail into the rail holders .

6

K

Step 13

6

Assembly Instructions

9

Step 14

Step 15

Prepare the left and right doors

Push fit 3 hinges into the left door and the right door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

J

O

9

10

90

O

J

O

J

O

J

Prepare the mirror door

Push fit 3 hinges into the mirror door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

J

O

11

9

Warning: Glass! Handle with care

O

J

O

J

O

J

10

O

J

O

J

O

J

11

Assembly Instructions

12

Step 16

Fit doors and handles

Note: The easiest way to attach each door , . and is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle to

the left door and the right door using screws .

O

P

O

P

M

H

9 10

11

9

10

a: b:

c: d:

P

O

P

B

P

O

A

O

P

B

e:

10

11

9

M

Warning: Glass! Handle with care

H

M

Note: To differentiate between the left and right door, the handles are positioned just below the centre of the door.

Assembly Instructions

Step 17

b:

c:

d:

a:

Adjust the doors if needed

a: Before adjusting the

doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

c: Forward and Back

adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.

A

B

C

13

Assembly Instructions

12

Step 18

Fit the overbalance protector

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.

Wall fixings are not supplied as they will need to suit the wall type.

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

L

WALL

Wall fixing

(not supplied)

Screw

(not supplied)

Washer

Strap

L

Strap

Washer

Screw

TOP OF UNIT

L

Assembly Instructions

ALR3116

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 19

Assembly is complete

IMPORTANT INFORMATION ABOUT THIS PRODUCT

This product complies with the requirements of BS 7449:1991 and has been manufactured by

DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,

THORNABY-ON-TEES, CLEVELAND, TS17 9LT

.

The product code for this unit and the item code(s) for the glass components are listed in the Assembly

Instructions along with a description of the type of glass used. All clear/tinted glass complies with the requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the

glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,

or agent with regard to obtaining a manufacturing specification and shape for replacement glass

quoting the unit description and batch number or date of manufacture.

Do not place very hot or very cold items against or in close proximity to glass surface(s) unless

adequately thick insulating material is used to prevent such items coming in contact with the glass.

Do not strike the glass with hard or pointed items. Do not sit or stand upon horizontal glass surfaces.

When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if

necessary - do not use washing powders or any other substance containing abrasives since these

substances scratch glass.

If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.

KEEP THESE INSTRUCTIONS FOR FUTURE USE