Argos Anderson - TV Unit ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 39.5cm
Height - 51.7cm
Anderson - TV Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 13/06/12
Important - Please read these instructions fully before starting assembly
609/5521
609/5514
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 24kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1499A)
(495 x 375mm)
Divider (D1502A)
(419.5 x 370mm)
Base (D1503A)
(966 x 371mm)
Drawer Front (D1504A)
(394 x 214mm) x 2
Plinth (D1505A)
(966 x 60mm)
Shelf (D1506A)
(577 x 369mm)
Right Side (D1500A)
(495 x 375mm)
Top (D1501A)
(999 x 395mm)
2
Left Drawer Side (W415LH)
(320 x 150mm) x 2
Right Drawer Side (W415RH)
(320 x 150mm) x 2
Back (X883)
(926 x 440mm)
Drawer Back (W526)
(322 x 150mm) x 2
Drawer Base (T526)
(333 x 317mm) x 2
3
5
4
7
10
8 9
6
12 13
11
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 5
B
Metal dowel (F901) x 13
C
D
Large locking nut (F900) x 9
E
Small locking nut (F3) x 4
F
G H I
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 21
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Knock-in Peg (F171) x 8
13mm Screw (F52) x 8
Shelf stud (F110) x 4
13mm Screw (F63) x 8
Handle (F847a ) x 2KHandle Screw (F847b) x 4
b
40mm Screw (F910) x 2
C
K
a
L
R Runner (F160) x 2
b
L Runner (F161) x 2
L
c
L Runner (F159) x 2
L
a
R Runner (F162) x 2
L
d
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
8
10
B
B
F
Step 2
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of the drawer front .
Note: Tighten metal dowels up fully against the panels.
B
8
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: Arrow on locking nut must point towards hole in edge of panel.
Step 3
F
10
11
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10 11
8
F
10 11
F
D
F
F
10
11
8
Small
groove
10
11
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
B
B
8
x 2
x 2 x 2
I
I
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
12
10 11
8
9
10 11
12
9
9
I
10 11
Attach the handle
Attach the handle to the drawer front using 2 screws .
8
K a
K b
8
10
11
12
8
11
12
10
I
I
9
K b
K b
K a
8
x 2
x 2
x 2
1
Assembly Instructions
6
Step 7
Fit runners to the drawers
Turn the drawer assemblies over.
Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit the runner to the bottom edge of the right drawer side using the same method.
11
L c
10
8
H
L d
L c
L d
Runners must be
pushed up against
the drawer front
Step 8
8
10
11
L a
G G
1st screw
2nd screw
Prepare the left side
Fit 2 runners to the left side .
The 1st screw uses the 2nd hole in from the front of the runner .
The 2nd screw uses the hole that lines up with the other panel hole.
L a
1
G
G
L a
G
G
L a
G
G
L a
H
H
H
H
x 2
Finished
front edge
Finished
front edge
A
A
Assembly Instructions
7
Step 9
Finish preparing the left side
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Screw 3 metal dowels into the left side .
Insert a large locking nut into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 10
E
10mm
A
A
1
B
1
1
E
Prepare the right side
Tap a wooden dowel into the right side .
Screw 3 metal dowels into the right side .
Insert a large locking nut into the right side . .
A
2
B
2
2
E
1
B
B
B
E
B
B
B
E
2
Finished
front edge
Finished
front edge
A
Assembly Instructions
8
Step 11
E
E
Prepare the base
Insert 4 large locking nuts into the base
6
E
.
E
E
plain chipboard surface
6
Step 12
Join the right side and base
Push the base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 13
B
E
plain chipboard surface
6
2
E
6
E
6
2
L b
G G
1st screw
2nd screw
Prepare the divider
Fit 2 runners to the divider .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd screw uses the hole that lines up with the other panel hole.
Tap a wooden dowel into the divider .
Insert a large locking nut into the divider .
L b
3
G
G
3
A
E
3
E
G
G
L b
3
G
G
L b
.
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 14
Step 16
Step 15
3
J
J
6
3
6
J
Fit the divider
Attach the divider to the base using 2 screws .
Prepare the plinth
Tap 2 wooden dowels into the plinth .
Insert 2 large locking nuts into the plinth
7
E
.
A
7
E
E
A
A
plain chipboard surface
plain chipboard surface
7
7
Fit the plinth
Push the plinth onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the plinth . .
E
7
2
7
2
Profiled
front edge
Assembly Instructions
10
Step 17
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 3 large locking nuts fitted to the base and the plinth .
1
E
6
7
1
6
7
B
B
B
5
Step 18
Prepare the top
Screw 3 metal dowels into the top .
Step 19
B
5
Fit the top
Push the top onto the assembly.
Use a screwdriver to tighten the 3 large locking nuts fitted to the left side , right side and divider .
2 3
1
5
E
5
2
3
1
Profiled
front edge
Assembly Instructions
11
Step 20
This gap is for
cable management
y
y
x
x
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit making sure that it is pushed into the rebate on the left side .
Nail the back into the left side , top , base and divider as shown.
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
13
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
1
6 3
5
D
1
1
C
x 4
Step 21
Fit the shelf studs
Insert 4 shelf studs into the holes on the right side and divider . .
C
2
3
2
3
13
6
3
5
Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 22
Fit the shelf
Lower the shelf down onto the shelf studs .
4
C
4
Step 23
Fit the drawers
Slide the wheels of the runners fitted to the drawer, over the wheels of the runners fitted to the unit and push the drawer into position.
Assembly is complete
Side panel
Drawer
Warning: The unit is heavy. Lift with care.
ALR2745
MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 39.5cm
Height - 51.7cm
Anderson - TV Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 05/04/13
Important - Please read these instructions fully before starting assembly
609/5521
609/5514
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 24kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
Left Drawer Side (W415LH)
(320 x 150mm) x 2
Right Drawer Side (W415RH)
(320 x 150mm) x 2
Drawer Back (W526)
(322 x 150mm) x 2
Drawer Base (T526)
(333 x 317mm) x 2
3
5
4
7
10
8 9
6
12 13
11
Left Side (D2273A)
(495 x 375mm)
Divider (D2276A)
(419.5 x 373mm)
Base (D2275A)
(966 x 374mm)
Drawer Front (D2278A)
(394 x 214mm) x 2
Plinth (D2277A)
(966 x 60mm)
Shelf (D2279A)
(577 x 369mm)
Right Side (D2274A)
(495 x 375mm)
Top (D2272A)
(999 x 398mm)
Back (X929-452)
(929 x 452mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 5
B
Metal dowel (F901) x 13
C
D
Large locking nut (F900) x 9
E
Small locking nut (F3) x 4
F
G H I
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Nail (F51) x 21
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Knock-in Peg (F171) x 8
13mm Screw (F52) x 8
Shelf stud (F110) x 4
13mm Screw (F63) x 8
Handle (F847a ) x 2KHandle Screw (F847b) x 4
b
40mm Screw (F910) x 2
C
K
a
L
R Runner (F160) x 2
b
L Runner (F161) x 2
L
c
L Runner (F159) x 2
L
a
R Runner (F162) x 2
L
d
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
8
10
B
B
F
Step 2
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of the drawer front .
Note: Tighten metal dowels up fully against the panels.
B
8
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: Arrow on locking nut must point towards hole in edge of panel.
Step 3
F
10
11
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10 11
8
F
10 11
F
D
F
F
10
11
8
Small
groove
10
11
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
B
B
8
x 2
x 2 x 2
I
I
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
12
10 11
8
9
10 11
12
9
9
I
10 11
Attach the handles
Attach a handle to each drawer front using 2 screws .
8
K a
K b
8
10
11
12
8
11
12
10
I
I
9
K b
K b
K a
8
x 2
x 2
x 2
Finished
front edge
Assembly Instructions
6
Step 7
Fit runners to the drawers
Turn the drawer assemblies over.
Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit the runner to the bottom edge of the right drawer side using the same method.
11
L c
10
8
H
L d
L c
L d
Runners must be
pushed up against
the drawer front
Step 8
8
10
11
L a
G G
1st screw
2nd screw
Prepare the left side
Fit 2 runners to the left side .
The 1st screw uses the 2nd hole in from the front of the runner .
The 2nd screw uses the hole that lines up with the other panel hole.
L a
1
G
G
L a
G
G
L a
G
G
L a
H
H
H
H
x 2
1
A
Finished
front edge
A
Assembly Instructions
7
Step 9
Finish preparing the left side
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Screw 3 metal dowels into the left side .
Insert a large locking nut into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 10
E
10mm
A
A
1
B
1
1
E
Prepare the right side
Tap a wooden dowel into the right side .
Screw 3 metal dowels into the right side .
Insert a large locking nut into the right side . .
A
2
B
2
2
E
B
B
B
E
B
B
B
E
2
Finished
front edge
1
A
Finished
front edge
Assembly Instructions
8
Step 11
E
E
Prepare the base
Insert 4 large locking nuts into the base
6
E
.
E
E
plain chipboard surface
6
Step 12
Join the right side and base
Push the base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 13
6
2
E
6
E
L b
G G
1st screw
2nd screw
Prepare the divider
Fit 2 runners to the divider .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd screw uses the hole that lines up with the other panel hole.
Tap a wooden dowel into the divider .
Insert a large locking nut into the divider .
L b
3
G
G
3
A
E
3
E
G
G
L b
3
.
Finished
front edge
Finished
front edge
plain chipboard surface
6
2
B
E
G
G
L b
Finished
front edge
Assembly Instructions
9
Step 14
Step 16
Step 15
3
6
J
Fit the divider
Attach the divider to the base using 2 screws .
Prepare the plinth
Tap 2 wooden dowels into the plinth .
Insert 2 large locking nuts into the plinth
7
E
.
A
7
E
E
A
A
plain chipboard surface
7
Fit the plinth
Push the plinth onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the plinth . .
E
7
2
7
J
J
3
6
plain chipboard surface
7
2
Profiled
front edge
Assembly Instructions
10
Step 17
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 3 large locking nuts fitted to the base and the plinth .
1
E
6
7
B
B
B
5
Step 18
Prepare the top
Screw 3 metal dowels into the top .
Step 19
B
5
Fit the top
Push the top onto the assembly.
Use a screwdriver to tighten the 3 large locking nuts fitted to the left side , right side and divider .
2 3
1
5
E
Profiled
front edge
7
6
1
2
1
3
5
Assembly Instructions
11
Step 20
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit making sure that it is positioned flush with the outside edge of the left side .
Nail the back into the left side , top , base and divider as shown.
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
13
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
1
6 3
5
1
Step 21
Fit the shelf studs
Insert 4 shelf studs into the holes on the right side and divider . .
C
2
3
13
3
b:
D
This gap is for
cable management
1
5
6
y
y
x
x
C
x 4
3
2
Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 22
Fit the shelf
Lower the shelf down onto the shelf studs .
4
C
Step 23
Fit the drawers
Slide the wheels of the runners fitted to the drawer, over the wheels of the runners fitted to the unit and push the drawer into position.
Assembly is complete
Side panel
Drawer
Warning: The unit is heavy. Lift with care.
4
ALR2745
Loading...