MADE IN
BRITAIN
Dimensions
Width - 71.5cm
Depth - 33.5cm
Height - 183.5cm
Anderson - Tall Bookcase
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 26/04/12
Important - Please read these instructions fully before starting assembly
609/6489
609/6472
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 32kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1540A)
(1809 x 320mm)
Top (D1539A)
(712 x 326mm)
Horizontal (D1544A)
(678 x 316mm) x 2
Drawer Front (D1542A)
(706 x 246mm)
6
2
Right Side (D1541A)
(1809 x 320mm)
Shelf (D1545A)
(677 x 316mm) x 2
Plinth (D1543A)
(678 x 60mm)
10
7
8
Left Drawer
Side (W415LH)
(320 x 150mm)
9
Right Drawer
Side (W415RH)
(320 x 150mm)
Drawer Base (T527)
(637 x 317mm)
Back (X887)
(1527 x 696mm)
Drawer Back (W527)
(626 x 150mm)
3
4
5
11 12
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
C
D
Large locking
nut (F900) x 12
E
Small locking
nut (F3) x 2
F
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 30
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Electric drill
(do not use for
fitting screws)
Knock-in Peg (F171) x 4
Bracket (F327) x 1
13mm Screw (F52) x 4
Shelf stud (F110) x 8
13mm Screw (F63) x 4
13mm Screw (F79) x 1
C
L
Handle
(F847a ) x 1
a
L
Handle Screw
(F847b) x 2
b
M
R Runner (F962) x 1
b
L Runner (F963) x 1
M
c
L Runner (F961) x 1
M
a
R Runner (F964) x 1
M
d
R
L
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
7
9
B
B
F
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
F
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
F
8
9
F
F
B
B
F
F
Small
groove
7
7
8
9
9
8
J
J
Assembly Instructions
5
Step 4
7
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
7
10
8 9
11
10
10
J
8 9
Attach the handle
Attach the handle
to the drawer front
using 2 screws .
7
11
L a
L b
9
8
7
11
9
8
10
J
J
L b
L b
L a
7
A
Assembly Instructions
6
Step 7
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
Turn the drawer over
9
M c
8
7
I
M d
Runners must be
pushed up against
the drawer front
8
9
7
B
B
B
B
B
E
E
M a
G
Finished front edge
G
1st
screw
2nd
screw
Prepare the left side
Tap a wooden dowel
into the left side .
Screw 5 metal dowels
into the left side .
Insert a large locking
nut into the left side
. .
Fit the runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd screw uses
the hole that lines up
with the other panel hole.
Step 8
A
1
1
B
E
1
1
M a
G
M a
G
10mm
A
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
1
M d
R
I
I
I
I
R
L
M c
L
G
L
G
M a
Finished
front edge
A
Assembly Instructions
7
Step 9
Step 10
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
horizontals .
R
G
G
M b
E
B
B
B
B
B
M b
G
Finished front edge
G
1st
screw
2nd
screw
Prepare the right side
Tap a wooden dowel
into the right side .
Screw 5 metal dowels
into the right side .
Insert a large locking
nut into the right side
. .
Fit the runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd screw uses
the hole that lines up
with the other panel hole.
A
2
2
B
E
2
2
M b
G
M b
G
2
E
E
E
E
4
E
4
Finished
front edge
Finished
front edge
x 2
Assembly Instructions
8
Step 11
Step 12
Finished
front edge
Finished
front edge
R
4
4
2
Join the right side and
horizontals
Push the 2 horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the 2 horizontals
. .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
E
4
2
E
4
E
E
E
6
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the
plinth .
Step 13
E
6
6
A
A
A
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the
plinth .
R
6
6
2
2
E
6
Assembly Instructions
9
Step 14
Step 15
R
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the 2 horizontals and
the plinth .
1
E
4
6
1
4
4
6
Prepare the top
Screw 2 metal dowels
into the top .
B
B
3
B
3
Assembly Instructions
10
Step 16
Step 17
R
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side and right
side .
3
E
1
2
3
1
2
yRy
y
x
x
b:
D
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails
should be
spaced about
150mm apart.
Stand the unit
up for the next step.
12
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
12
12
Warning: The
unit is heavy.
Lift with care.
Assembly Instructions
11
Step 18
R
3
K
Top of Unit
WALL
WALL
Back of Unit
Attach bracket to top
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
Screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
K
K
H
K
K
H
K
H
K
Assembly Instructions
12
Step 19
R
Step 20
Fit the shelves
Lower the 2 shelves
down onto the shelf
studs .
Fit the shelf studs
For each of the 2
shelves , insert 4 shelf
studs at the required
height.
C
C
x 4
C
x 4
5
C
R
5
5
5
Assembly Instructions
13
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 21
Side
panel
Drawer
side
Fit the drawer
Slide the wheels on the
runners fitted to the
drawer sides over the
wheels on the runners
fitted to the side panels
and push the drawer into
position.
Assembly is complete
Warning: The
unit is heavy.
Lift with care.
ALR2743
MADE IN
BRITAIN
Dimensions
Width - 71.5cm
Depth - 33.5cm
Height - 183.5cm
Anderson - Tall Bookcase
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 03/04/13
Important - Please read these instructions fully before starting assembly
609/6489
609/6472
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 32kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
6
2
10
7
8
Left Drawer
Side (W415LH)
(320 x 150mm)
9
Right Drawer
Side (W415RH)
(320 x 150mm)
Drawer Base (T527)
(637 x 317mm)
Drawer Back (W527)
(626 x 150mm)
3
4
5
11 12
Top (D2286A)
(712 x 329mm)
Drawer Front (D2291A)
(706 x 246mm)
Shelf (D2290A)
(677 x 319mm) x 2
Plinth (D2292A)
(678 x 60mm) x 2
Horizontal (D2289A)
(678 x 319mm) x 2
Left Side (D2287A)
(1809 x 320mm)
Right Side (D2288A)
(1809 x 320mm)
Back (X887)
(1527 x 696mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 14
C
D
Large locking
nut (F900) x 12
E
Small locking
nut (F3) x 2
F
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 30
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Electric drill
(do not use for
fitting screws)
Knock-in Peg (F171) x 4
Bracket (F327) x 1
13mm Screw (F52) x 4
Shelf stud (F110) x 8
13mm Screw (F63) x 4
13mm Screw (F79) x 1
C
L
Handle
(F847a ) x 1
a
L
Handle Screw
(F847b) x 2
b
M
R Runner (F962) x 1
b
L Runner (F963) x 1
M
c
L Runner (F961) x 1
M
a
R Runner (F964) x 1
M
d
R
L
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
7
9
B
B
F
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
F
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
F
8
9
F
F
B
B
F
F
Small
groove
8
9
9
8
7
7
J
J
Assembly Instructions
5
Step 4
7
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
7
10
8 9
11
10
10
J
8 9
Attach the handle
Attach the handle
to the drawer front
using 2 screws .
7
11
L a
L b
9
8
11
9
8
10
J
J
L b
L b
L a
7
7
A
Assembly Instructions
6
Step 7
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
Turn the drawer over
9
M c
8
7
I
M d
Runners must be
pushed up against
the drawer front
8
9
7
B
B
B
B
B
E
E
M a
G
Finished front edge
G
1st
screw
2nd
screw
Prepare the left side
Tap a wooden dowel
into the left side .
Screw 5 metal dowels
into the left side .
Insert a large locking
nut into the left side
. .
Fit the runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd screw uses
the hole that lines up
with the other panel hole.
Step 8
A
1
1
B
E
1
1
M a
G
M a
G
10mm
A
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
1
M d
R
I
I
I
I
R
L
M c
L
Finished
front edge
G
L
G
M a
A
Assembly Instructions
7
Step 9
Step 10
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
horizontals .
R
G
G
M b
E
B
B
B
B
B
M b
G
Finished front edge
G
1st
screw
2nd
screw
Prepare the right side
Tap a wooden dowel
into the right side .
Screw 5 metal dowels
into the right side .
Insert a large locking
nut into the right side
. .
Fit the runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
The 2nd screw uses
the hole that lines up
with the other panel hole.
A
2
2
B
E
2
2
M b
G
M b
G
2
E
E
E
E
4
E
4
Finished
front edge
Finished
front edge
x 2
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 11
Step 12
Join the right side and
horizontals
Push the 2 horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the 2 horizontals
. .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
E
4
2
E
4
E
E
E
6
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the
plinth .
Step 13
E
6
6
A
A
A
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the
plinth .
6
2
E
6
R
4
4
2
Plain
chipboard
surface
R
2
6
Assembly Instructions
9
Step 14
Step 15
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the 2 horizontals and
the plinth .
1
E
4
6
Prepare the top
Screw 2 metal dowels
into the top .
B
B
3
B
3
R
6
R
1
4
4
Assembly Instructions
10
Step 16
Step 17
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side and right
side .
3
E
1
2
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails
should be
spaced about
150mm apart.
Stand the unit
up for the next step.
12
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
12
Warning: The
unit is heavy.
Lift with care.
R
R
3
1
2
R
R
yy
y
x
x
12
b:
D
Assembly Instructions
11
Step 18
Top of Unit
WALL
WALL
Back of Unit
Attach bracket to top
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
Screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
K
K
H
K
K
H
K
R
K
H
3
Assembly Instructions
12
Step 19
Step 20
Fit the shelves
Lower the 2 shelves
down onto the shelf
studs .
Fit the shelf studs
For each of the 2
shelves , insert 4 shelf
studs at the required
height.
C
5
C
5
R
R
C
x 4
C
x 4
5
5
Assembly Instructions
13
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 21
Side
panel
Drawer
side
Fit the drawer
Slide the wheels on the
runners fitted to the
drawer sides over the
wheels on the runners
fitted to the side panels
and push the drawer into
position.
Assembly is complete
Warning: The
unit is heavy.
Lift with care.
ALR2743
Loading...