Argos Anderson - 4 Drawer Chest ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Anderson - 4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Important - Please read these instructions fully before starting assembly
Width - 75cm
Depth - 40cm
Height - 74.5cm
Issue 3 - 03/04/14
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 26kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
4
6
Drawer Front (D0218A)
(737 x 162mm) x 4
2
3
5
10
9
Drawer Base (T695-367)
(695 x 367mm) x 4
Drawer Back (W684-124)
(684 x 124mm) x 4
Rail (D2201A)
(717 x 60mm) x 2
Top (D2200A)
(750 x 396mm)
Left Side (D2198A)
(721 x 372mm)
Right Side (D2199A)
(721 x 372mm)
Back (X741-700)
(741 x 700mm)
7
8
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 4
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 14
C
D E F
G
K
Rule Scissors Hammer Eye protection
(when using a hammer or drill)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking nut (F900) x 6
Nail (F51) x 19
Small locking nut (F3) x 8
9mm Screw (F73) x 16
9mm Screw (F74) x 8
H
Drawer runner (F1004) x 8
Cross-head screwdriver
I
Handle (F847a ) x 4
a
I
Handle screw (F847b) x 8
b J
Knock-in Peg (F171GY) x 16
L
Wedgefix (F639) x 16
Plastic Nail (F91) x 4
Assembly Instructions
4
Step 1
B
B
B
6
Step 2
Prepare the drawer fronts
Screw 2 metal dowels into the holes shown on the back of each drawer front .
Note: Tighten metal dowels up fully against the panels.
B
6
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: Arrow on locking nut must point towards hole in edge of panel.
Step 3
D
7
8
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
6
D
7 8
x 4
D
x 4
Small groove
6
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
B
B
D
D
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
D
D
7
8
x 4
x 4
7
8
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
J
7 8
Attach the handles
Attach a handle to each drawer front using 2 screws .
6
I a
I b
6
6
x 4
x 4
11
J
J
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
L
J
J
L
L
L
9
7
8
10
8
10
7
6
I
7
I b
I b
I a
6
x 4
6
L
L
x 4
A
Assembly Instructions
6
Step 8
Unfinished
back edge
F
H
a:
b:
Finished
front edge
F
H
Finished
front edge
Finished
front edge
F
H
F
H
F
H
F
H
F
F
F
F
Prepare the left side
a: Place 4 runners on
left side . Slide back top of runner and use 2nd hole from the front to fit 1st screw .
b: Slide runner back the
other way and use 2nd hole from the back to fit 2nd screw .
c: Insert 1 large locking
nut into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Screw 2 metal dowels into the left side .
1
H
F
F
1
1
c:
C
B
B
1
C
1
A
B
1
1
10mm
A
C
A
Assembly Instructions
Step 9
7
Prepare the right side
a: Place 4 runners on
right side . Slide back top of runner and use 2nd hole from the front to fit 1st screw .
b: Slide runner back the
other way and use 2nd hole from the back to fit 2nd screw .
c: Insert 1 large locking
nut into the right side .
Tap a wooden dowel into the right side .
Screw 2 metal dowels into the right side .
2
H
F
b:
c:
a:
Finished
front edge
F
H
Unfinished
back edge
F
H
F
H
F
H
F
H
F
H
2
Finished front edge
F
F
F
F
Finished front edge
2
F
2
C
B
B
C
2
2
2
A
B
A
Assembly Instructions
8
Step 10
A
C
C
Prepare the 2 rails
Insert 2 large locking nuts into the holes in the 2 rails .
Tap 1 wooden dowel into each end of the 2 rails .
4
C
A
4
plain chipboard surface
4
Step 11
Fit the 2 rails
Push the 2 rails onto right side as shown.
Use a screwdriver to tighten the 2 large locking nuts fitted to the 2 rails.
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
C
C
4
2
Support this rail until the left side
has been fitted in
the next step.
x 2
plain chipboard surface
4
plain chipboard surface
4
2
B
C
Assembly Instructions
Step 12
9
Step 13
1
4
C
4
C
Fit the left side
Fit the left side to the 2 rails .
Use a screwdriver to tighten the 2 large locking nuts fitted to the 2 rails .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Stand the unit up.
B
B
Prepare the top
Screw 2 metal dowels into the top .
Note: Tighten metal dowels up fully against the panel.
B
3
3
4
4
1
Assembly Instructions
10
Step 14
Step 15
Fit the top
Lower the top onto the side panels and . .
Use a screwdriver to tighten the 2 large locking nuts fitted to the inside of the left side . and right side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Lay the unit down onto its front again.
3
1
2
C
1 2
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
Fit the back and plastic nails
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the foldy back
. onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
5
E
5
Warning: The unit is heavy. Lift with care.
3
1
2
y
y
x
b:
E
5
2
Tap 2 plastic nails into the bottom edge of each of the sides and . .
K
1
2
K
K
K
K
Stand the unit up for the next step.
1
x
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
H
Step 16
2nd threaded
hole
G
Warning: The unit is heavy. Lift with care.
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner .
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
G
H
7 8
H
H
G
7
H
ALR3008
G
G
H
Loading...