Argos Anderson - 3 Door Tall Robe ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
Width - 149.5cm
Depth - 50cm
Height - 199.5cm
Anderson - 3 Door Tall Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue - 03/04/14
Important - Please read these instructions fully before starting assembly
274/9668
239/2819
259/2468
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 89kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
2 3
4
Top (D2047A)
(1495 x 496mm)
Base (D2050A)
(1461 x 470mm)
7
9
8
13
Large Shelf (D2052A)
(965 x 467mm)
5
Back Rail (D2053A)
(965 x 120mm)
6
Plinth (D2054A)
(1461 x 80mm)
Small Shelf (D2060A)
(479 x 467mm)
10
14
Door (D2056A)
(1894 x 494mm) x 3
Large Hanging Rail (FHR957)
(957mm long) x 2
11
Small Hanging Rail (FHR471)
(471mm long) x 2
12
Large Back (X956)
(1914 x 988mm)
Small Back (X955)
(1914 x 499mm)
Divider (D2051B)
(1883 x 469mm)
Left Side (D2048B)
(1978 x 471mm)
Right Side (D2049B)
(1978 x 471mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 14
C
P
Handle (F266) x 3
K
Hinge plate (F523) x 12
I
O
Bracket (F327) x 1
E
Nail screw (F277) x 8
D
Nail (F51) x 46
Large locking
nut (F900) x 14
L
Hinge (F518) x 12
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
H
F
Back holder (F276) x 8
N
Shelf stud (F110) x 8
G
13mm Screw (F63) x 32
M
Rail holder
(F1014) x 8
13mm Screw (F79) x 1
19mm Screw (F461) x 6
40mm Screw (F910) x 2
J
Q
Plastic Nail (F91) x 5
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the divider
Screw a metal dowel
into the divider .
Note: Tighten metal
dowels up fully against
the panel.
Fit 4 hinge plates onto
the divider , making
sure that the slot is
facing towards the
finished front edge.
Insert 2 large locking
nuts into the divider
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
K
3
A
3
C
3
3
B
Prepare the base
Insert 4 large locking
nuts into the base .
Tap 2 wooden dowels
into the base .
C
8
A
8
Step 2
Finished
front edge
C
C
K
K
K
K
A
3
B
B
C
10mm
A
K
A
C
C
C
C
A
plain chipboard surface
8
Finished
front edge
Loading...