MADE IN
BRITAIN
Dimensions
Anderson - 2 Drawer Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Important - Please read these instructions fully before starting assembly
Width - 38cm
Depth - 40cm
Height - 44.5cm
Issue 3 - 03/04/14
258/6357
249/7082
268/3872
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 11kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
4
2 3
Drawer Front (D0211A)
(367 x 176mm) x 2
5
10
Left Side (D2166A)
(422 x 372mm)
Right Side (D2167A)
(422 x 372mm)
Top (D2168A)
(380 x 396mm)
Rail (D2169A)
(347 x 60mm) x 2
Back (X400-370)
(400 x 370mm)
7
Drawer Back (W314-124)
(314 x 124mm) x 2
Drawer Base (T325-367)
(325 x 367mm) x 2
6
8
9
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Right Drawer Side (W370-124RH)
(370 x 124mm) x 2
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 10
C
D E F
G
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking
nut (F900) x 6
Nail (F51) x 10
Small locking
nut (F3) x 4
9mm Screw (F73) x 8
9mm Screw (F74) x 4
I
Handle (F847a ) x 2
a
I
Handle screw (F847b) x 4
b
H
Drawer runner (F1004) x 4
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
J
Knock-in Peg (F171) x 8
L
Plastic Nail (F91) x 4
K
Wedgefix (F639) x 4
Assembly Instructions
4
Step 1
B
B
B
5
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
7
8
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
D
7
8
x 2
D
B
B
D
5
Small groove
9
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
D
D
7
8
8
7
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
6
7 8
5
9
7 8
6
9
9
J
7 8
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
5
I a
I b
x 2
x 2
x 2
5
11
I a
325mm
J
J
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
J
J
K
K
K
9
7
8
6
8
6
7
5
I b
I b
5
x 2
A
Assembly Instructions
6
Step 8
10mm
A
Finished
front edge
F
H
Rebated
back edge
F
H
c:
b:
a:
Prepare the left side
a: Place 2 runners on
left side . Slide back
top of runner and use
2nd hole from the front
to fit 1st screw .
b: Slide runner back the
other way and use 2nd
hole from the back to fit
2nd screw .
c: Insert 1 large locking
nut into the left side
. as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap in wooden dowel
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 2 metal dowels
into the holes shown.
1
H
F
F
C
A
B
1
F
H
F
H
1
Finished
front edge
Finished
front edge
Finished
front edge
F
F
1
1
C
B
B
C
A
Assembly Instructions
7
Step 9
Prepare the right side
a: Place 2 runners on
right side . Slide back
top of runner and use
2nd hole from the front
to fit 1st screw .
b: Slide runner back the
other way and use 2nd
hole from the back to fit
2nd screw .
c: Insert 1 large locking
nut into the right
side as shown.
Tap in wooden dowel
as shown.
Screw 2 metal dowels
into the holes shown.
2
H
F
F
a:
b:
C
Finished
front edge
F
H
Rebated
back edge
F
H
c:
2
A
B
F
H
F
H
F
F
2
2
2
B
B
C
Finished front edge
Finished front edge
Finished front edge
Assembly Instructions
Prepare the 2 rails
Insert 2 large locking
nuts into the holes in
the 2 rails .
Tap 2 wooden dowels
into the ends of the 2
rails .
4
Step 10
Step 11
8
A
A
C
C
C
A
4
4
Fit the 2 rails
Push the 2 rails onto
right side as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
C
C
B
C
4
2
Plain
chipboard
surface
A
A
C
C
4
Plain
chipboard
surface
Plain
chipboard
surface
Support this rail
until the left side
has been fitted in
the next step.
4
4
2
Assembly Instructions
9
Step 12
Fit the left side
Fit the left side to the
2 rails .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 13
1
4
C
4
C
B
B
Prepare the top
Screw 2 metal dowels
into the top .
Note: Tighten metal
dowels up fully against
the panel.
Step 14
B
3
3
Fit the top
Push the top onto
side panels and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the inside of the side
panels and .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1 2
1 2
C
C
4
4
1
1
3
2
Assembly Instructions
10
Step 15
b:
Fit the back and
plastic nails
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about 150mm
apart.
10
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
y
y
x
E
10
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
L
1
2
Stand the unit up
for the next step.
L
L
L
L
1
2
x
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 16
Fit the drawers
Starting with the bottom
drawer, slide both the
runners forward and
locate the drawer
sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner .
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
Assembly is complete
G
H
2nd threaded
hole
G
7 8
H
H
G
7
H
ALR3007
G
G
Loading...