MADE IN
BRITAIN
Dimensions
Width - 70.5cm
Depth - 52cm
Height - 183cm
Anderson - 1 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 03/04/14
Important - Please read these instructions fully before starting assembly
246/6848
248/4150
247/3329
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 48kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Drawer Back (W639-124)
(639 x 124mm)
2
3
4
6
11
13 14
9
8
5
7
10
Hanging Rail (FHR660)
(660mm long)
12
Drawer Base (T650-367)
(650 x 367mm)
Left Side (D2356A)
(1808 x 494mm)
Top (D2355A)
(702 x 516mm)
Right Side (D2357A)
(1808 x 494mm)
Base (D2358A)
(669 x 493mm)
Horizontal (D2359A)
(669 x 493mm)
Door (D2361A)
(1559 x 345mm) x 2
Plinth (D2360A)
(669 x 80mm)
Drawer Front (D2362A)
(692 x 162mm)
Back (X1590-695)
(1590 x 695mm)
Left Drawer Side
(W370-124LH)
(370 x 124mm)
Right Drawer Side
(W370-124RH)
(370 x 124mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 16
C
G
J
L
Handle (F847a) x 3
a
J
Handle Screw (F847b) x 6
b
H
M
N
Hinge (F518) x 6
Hinge plate (F523) x 6
F
13mm Screw (F63) x 14
I
E
13mm Screw (F79) x 1
D
Large locking
nut (F900) x 14
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
9mm Screw (F73) x 49mm Screw (F74) x 2
O
Drawer runner (F1004) x 2
Knock-in Peg (F171) x 4
Small locking
nut (F3) x 2
Rail holder
(F1014) x 2
K
Bracket (F327) x 1
P
Nail (F51) x 33
R
Plastic Nail (F91) x 4
Q
Wedgefix (F639) x 4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
9
10
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
7
D
D
9
10
B
B
7
Small groove
7
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
B
B
D
D
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
D
D
9
10
9
10
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
then down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
9 10
7
8
9 10
9 10
11
8
8
I
Attach the handle
Attach the handle
to the drawer front
using 2 screws .
7
J a
J b
.
7
6
11
I
I
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
Q
I
I
Q
Q
Q
8
9
10
11
10
11
9
7
I
7
J b
J b
J a
6
7
Q
Q
Finished
front edge
Finished
front edge
Finished
front edge
A
Assembly Instructions
6
Step 8
Finished
front edge
H
O
H
O
Prepare the left side
a: Place a runner on
the left side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
Screw 5 metal dowels
into the left side .
c: Tap a wooden dowel
. into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
H
M
M
M
B
B
B
B
B
C
M
10mm
A
C
L
C
O
1
H
H
1
1
1
B
A
C
1
L
F
M
1
1
1
1
1
a:
b:
c:
F
A
Assembly Instructions
7
Step 9
Finished
front edge
H
O
H
O
Prepare the right side
a: Place a runner on
the right side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
Screw 5 metal dowels
into the right side .
c: Tap a wooden dowel
. into the right side .
Insert 2 large locking
nuts into the right
side .
Push a rail holder into
the right side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
O
2
H
H
2
2
2
B
A
C
2
L
F
M
2
2
H
B
B
B
B
B
C
C
L
M
M
M
M
Finished
front edge
a:
b:
c:
2
2
2
F
Finished
front edge
Finished
front edge
Finished
front edge
Prepare the base and
horizontal
Tap 2 wooden dowels
into the base .
Insert 4 large locking
nuts into the base
Tap 2 wooden dowels
into the horizontal .
Insert 4 large locking
nuts into the
horizontal .
Assembly Instructions
8
Step 10
A
A
C
C
C
C
A
A
C
C
C
C
Finished
front edge
Finished
front edge
A
4
6
4
4
C
A
6
6
C
.
Join the horizontal
and base to the right
side
Push the horizontal
and base onto the
right side as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
both the horizontal
and base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 11
B
C
6
2
4
4
C
6
C
The base has a plain
chipboard surface
6
2
4
plain
chipboard
surface
Assembly Instructions
9
Step 12
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the plinth
A
A
A
C
C
Plain chipboard
surface
5
5
5
C
.
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
5
2
C
5
Step 13
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the horizontal , plinth
. and base .
Step 14
1
C
6
5 4
525
55
1
6
4
Note: To make it easier
to fit the top panel, place
a polystyrene block from
the packaging underneath
the side panels to raise
the assembly.
Assembly Instructions
10
Step 15
Prepare the top
Screw 4 metal dowels
into the holes shown on
the top .
B
3
Fit the top
Push the top onto
the side panels and
. .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the side panels and
. .
Step 16
3
1
2
C
1
2
B
B
B
B
3
Rounded
front edge
Rounded
front edge
3
1
2
Assembly Instructions
11
Step 17
Step 18
Fit the back
a: Square up the unit
by making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about
150mm apart.
14
P
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
14
Warning: The
unit is heavy.
Lift with care.
12
L
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
12
L
y
y
x
14
b:
P
12
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
R
1
2
R
Stand the unit up
for the next step.
R
R
R
x
1
2
Assembly Instructions
12
Step 19
Step 20
Fit the drawer
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
G
O
O
G
2nd threaded
hole
O
G
9 10
Prepare the 2 doors
Push fit 3 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
N
13
N
F
F
90
N
13
x 2
G
G
N
F
F
N
F
F
9
10
Assembly Instructions
13
Step 21
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT BE AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle
to each door using 2
screws .
N
N
N
M
M
M
N
M
e:
a: b:
c: d:
M
N
M
M
B
M
N
N
N
A
N
M
B
13
13
J a
J b
J a
J b
J b
13
J a
13
Assembly Instructions
14
Step 22
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3003
Step 23
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
Screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
K
K
E
K
K
E
K
E
K
K
Loading...