Shelby - Cabin Bed
Assembly Instructions - Please keep for future reference
322/0296
338/9663
Dimensions
Width - 195cm
Depth - 95.5cm
Height - 53cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800
Issue 1 - 9/02/10
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and ttings are
tightend properly.
• WARNING: Do not place this child`s bed near heat
sources, windows and other furniture.
• WARNING: Do not use this child`s bed if any part is
broken, torn or missing.
• WARNING: Not suitable for children under the age of
4 years.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
If you have damaged or missing components,
Components - Panels
call the Customer Helpline:
Please check you have all the panels listed below
Left side panel (95.5 x 53cm)
1
2
0345 6400800
Right side panel (95.5 x 53cm)
Front bed board (192 x 39.45cm)
3
Back bed board (192 x 56.05cm)
4
Front/Back bed supports x2 (192 x 14.3cm)
5
Right central support (32 x 37.2cm)
6
Right bottom panel (32 x 37.2cm)
8
Left central support (63 x 37.2cm)
7
Left bottom panel (63 x 37.2cm)
9
2
If you have damaged or missing components,
Components - Panels
call the Customer Helpline:
Please check you have all the panels listed below
0345 6400800
Middle crossbar (94 x 12cm)
10
Front crossbar (94 x 10cm)
12
Left shelf partition (94 x 37.2cm)
13
Back crossbar (94 x 10cm)
11
Right shelf partition (94 x 37.2cm)
14
Shelf (32 x 37.2cm)
15
Front board (192 x 4cm)
17
Drawer sides x2 (159.5 x 12cm)
18
Drawer bottom panel x2 (90.3 x 33.9cm)
19
Drawer front x2 (96.9 x 16cm)
16
3
Components - Fittings
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
A
50mm wood screw x 20
D
Locking nut x 4
G
Shelf support x 4
J
Left outside runner x 2
M N
Right inside runner x 2
B
50mm xing screw x 31
E
Screw-in dowel x 4
H
16mm wood screw x 38
K
Left inside runner x 2
Plastic support x 7
C
30mm wooden dowel x 14
F
Plastic support x 4
I
13mm xing screw x 12
L
Right outside runner x 2
O
Allen key x 1
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Drill
Ruler - Use this ruler to help correctly identify the screws
105
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
110 115 120 125 130 135 140 145 150 155 160 165 170
Small
hammer
Eye protection
(when using a
hammer)
4