Argos 652/9482, 673/1902, 620/9379, 673/2176, 618/4999 User guide

New Hallingford - 3 Drawer Bedside

Assembly Instructions - Important: Retain these instructions

for future reference

652/9482

618/4999

673/1902

620/9379

673/2176

601/6737

677/5449

618/6959

678/3699

616/9749

887/6449

916/0109

In order to prevent overturning, this product must be

Dimensions

Width - 37.5cm

Depth - 40cm

Height - 58cm

WARNING!

used with the wall attachment device provided

More help is available throughout this

booklet by scanning in the QR codes

or typing in the links

MADE IN

BRITAIN

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0330 016 1114
For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 15 - 13/11/19

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 14kgs.
Please lift with care.

• Assembly to be carried out by
a competent adult only.

• Check you have all the
components and tools listed on
pages 1, 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• During assembly children
should be kept away from the
product due to possible risk of
injury.

• Installation shall only be
carried out exactly according to
the manufacturer’s instructions

- otherwise a safety risk can
occur if incorrectly installed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance
protector kit supplied.

• Dispose of all packaging
carefully and responsibly.

• Do not use this item if any
components are missing or
damaged.

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

Tools required

Scissors

Rule

Flat-head
screwdriver

Cross-head
screwdriver

• From time to time check that
there are no loose screws on
this unit.

Bradawl

Hammer

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Eye protection
(when using a
hammer or drill)

Electric drill
(do not use for
fitting screws)

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

Components - Panels

Please check you have all the panels listed below

1 Left Side

(55.6 x 37.2cm)

4 5

Rail (D2310A)

(34.1 x 6cm)

(D2307A)

x 2

Left Drawer Side (W370-124LH)

(37 x 12.4cm)

x 3

2

Right Side (D2308A)

(55.6 x 37.2cm)

Drawer Front

(36.2 x 16.2cm)

Right Drawer Side

(37 x 12.4cm)

(D2309A)

x 3

x 3

(W370-124RH)

Top

3

86 7

(D2306A)

(37.5 x 39.6cm)

Drawer Back (W291-124)

(29.1 x 12.4cm)

x 3

9 10

Drawer Base (T304-367)

(30.4 x 36.7cm)

x 3

Back (X535-366)

(53.5 x 36.6cm)

2

Components - Fittings

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel

(F22) x 6

B C

Metal dowel (F901) x 12

D E F

Large locking cam
nut

(F900) x 6

Knock-in Peg

(F171GY) x 12

G H

19mm

Screw (F461) x 6

J

L

Handle (F278) x 3

9mm Screw (F73) x 18

a

K

b

K

350mm long

CL

CL Runner

CR Runner (F424) x 3

Nail (F51) x 12

I

13mm Screw

(F422) x 3

Small locking cam

(F3) x 6

nut

(F63) x 18

CR

c

Wedgefix

(F639) x 6

K

K

d

DL

M

Plastic Nail

(F91) x 4

N

Overbalance protector

F474) x 1

kit (

Ruler - Use this ruler to help correctly identify the screws

DL Runner (F425) x 3

DR Runner

(F426) x 3

DR

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

3

Assembly Instructions

Step 1

Prepare the 3 drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten metal
dowels up fully against
the panels.

5

B

Step 2

Prepare the drawer
sides

Insert a small locking
cam nut into the hole
shown on the left drawer
side and right drawer
side .

Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.

C

6

7

Drawer Assembly

www.youtube.com/watch?v=3fYL5zB6ZYQ

B

B

B

5

C

C

6

x 3

x 3 x 3

C

7

Step 3

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side

6
7

. onto the back of the
drawer front .

Turn the small locking
cam nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
cam nuts clockwise
to secure panels - more
than 1/2 a turn.

5

C

6
7

C

Groove

C

7

B

B

6

5

x 3

4

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

5

6 7

9

Step 5

Fit the drawer back

Fit the drawer back
between the drawer
sides and .

Make sure that the
drawer base fits into
the groove in the drawer
back .

6 7

9

8

8

9

7

6

5

8

E

E

6

9

x 3

E

E

7

x 3

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

E

6 7

8

Step 6

Attach the handle

Attach a handle to
each drawer front
using 2 screws .

J

5

G

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

L

G

G

5

L

x 3

L

x 3

J

Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.

L

5

Assembly Instructions

Step 8

Fit runners to the
drawers

Turn the 3 drawer
assemblies over.

Fit runner , marked
with ‘DR’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. .

5

Use a bradawl to mark
the fixing positions, then
secure with 2 screws .

Fit runner , marked
‘DL’, to the bottom edge
of the left drawer side
using the same method.

K d

7

I

K c

6

Fixing Bottom Mounter Runners

hps://www.youtube.com/watch?v=Z6lGMy19h7Q

Runners must be

pushed up against

the drawer front

I

DL

I

Bradawl

5

I

DL

6

7

I

Bradawl

x 3

K c

DR

K d

Step 9

Prepare the 2 rails

Tap 2 wooden dowels
into each rail .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 2 large locking cam
nuts into each rail .

D

Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.

4

A

4

D

A

x 2

D

D

4

A

A

10mm

6

Assembly Instructions

Step 10

Prepare the left side

a: Fit 3 CL runners

to the left side .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

H

up with the other panel
holes.

K a

1

H

Fixing Bottom Mounter Runners

hps://www.youtube.com/watch?v=Z6lGMy19h7Q

1st

front edge

Finished

a:

H

screw

Finished

front edge

H

K a

CL

H

H

H

H

CL

CL

1

H

K a

K a

H

CL

H

H

K a

b: Mark the top hole of

the runners with a
bradawl and then fit a
screw .

Screw 2 metal dowels
into the left side .

Insert a large locking
cam nut into the left
side . .

1

Tap a wooden dowel
into the left side .

K a

I

B

1

D

A

1

front edge

Finished

Bradawl

Finished

front edge

b:

K a

D

I

B

I

I

B

CL

CL

1

CL

A

7

Assembly Instructions

Step 11

Prepare the right side

a: Fit 3 CR runners

to the right side .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws

H

. use the holes that line
up with the other panel
holes.

b: Mark the top hole of

the runners with a
bradawl and then fit a
screw .

Screw 2 metal dowels
into the right side .

K b

I

K b

2

H

B

2

a:

b:

H

H

H

H

2

H

H

CR

K b

H

H

H

CR

CR

K b

K b

Finished

front edge

1st
screw

K b

CR

A

B

B

I

I

CR

CR

D

I

H

Bradawl

K b

front edge

Finished

front edge

Finished

Insert a large locking
cam nut into the right
side .

Tap a wooden dowel
into the right side .

D

2

A

2

Step 12

Join the right side and
rails

Push the 2 rails onto
the right side .

Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .

Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.

4

2

D

4

D

2

CR

Finished

front edge

B

2

4

CR

CR

CR

D

Note: Support this
rail until the left

4

side has been fitted
in the next step.

8

Assembly Instructions

Step 13

Fit the left side

Push the left side
onto the 2 rails .

1

4

Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .

D

4

Step 14

Prepare the top

Screw 2 metal dowels
into the top .

3

Fit the bracket from the
overbalance protector kit
. to the shallow

N

mark-hole drilled into
the top using 1 of its

3

screws.

B

CR

B

Shaped

front edge

4

CR

CR

1

4

N

B

N

3

Note: Only fit 1 of the
screws, the other 1 will
be fitted later.

Step 15

Fit the top

Push the top onto
the 2 sides and .

Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the sides

2

and .

9

3

1 2

D

3

2

CR

CR

CR

1

1

Assembly Instructions

Step 16

Fit the back

a: Square up the unit by

making sure that
measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the

F

outside edges of the

10

back .

Note: Nails should be
spaced about 150mm
apart.

10

Squaring up a Chest and tting the Back Panel

www.youtube.com/watch?v=FeaI6541z7o

The measurement from top corner X to bottom corner X must be

a:

equal to the measurement from top corner Y to bottom corner Y

b:

F

x

y

y

10

CR

CR

CR

x

Step 17

Fit the 4 plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

2

Stand the unit up for
the next step.

Warning: The
unit is heavy.
Lift with care.

M

1

M

M

CR

CR

2

CR

M

1

M

10

Assembly Instructions

Step 18

Secure the unit to a
wall

a: Before fitting the unit

to a wall, use a spirit
level to check the top of
the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.

In order to prevent overturning

this product must be used with the

wall attachment device provided

a:

WARNING!

To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting the
overbalance protector kit
. to a wall.

N

b: Push the unit up

against the wall and slide
the bracket against the
wall. Fit the 2nd screw
into the underside of the
top panel.

Mark the slot at the back
of the bracket for drilling
into the wall.

Wall fixings are not
supplied as they will need
to suit the wall type.

b:

Top

N

Back

See the next page for a guide
to wall mounting and fixings

N

Top

N

11

A Guide to Wall Mounting & Fixings

Important note:

If plastic wall plugs
are supplied with your
product:

- these are only suitable for
use in masonry walls.

If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.

Failure of the product due to
using incorrect fixings is the
responsibility of the installer.

Important: When drilling into walls always
check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.

Types of walls

You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.

No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug

Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.

No.2 “Plasterboard” wall plug

For use with plasterboard partitions or
hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.

No.6 “Shield Anchor” wall plug
Heavy loads

For use when attaching light loads on
to plasterboard partitions.

Care &
Maintenance

For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.

Safety: Always check the fitting
and location to ensure your safety
in and around the home.

For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.

Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

12

Assembly Instructions

Step 19

Fit the drawers

Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.

Fixing Bottom Mounter Runners

hps://www.youtube.com/watch?v=Z6lGMy19h7Q

Side

panel

Drawer

13

Assembly is complete

Please remove any blue protective film from panel

edges and clear protective film from panel surfaces

ALR2976