Osaka 3 Drawer Chest
Assembly Instructions - Please keep for future reference
White 2556868
Black 2494700
Dimensions
:
Width
Depth
Height
80.1 cm
:
40.0 cm
:
72.4 cm
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30
350261
Issue 1 - 15-05-2014
Safety and Care Advice
!
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.
1
If you have damaged or missing components, call
Components - Panels
the Argos Customer Helpline: 0845 640 30 30
Please check you have all the panels listed below
1
Top
(80,1 cm x 40 cm)
Front rail
4
(68,3 cm x 6 cm)
5
Back rail
(68,3 cm x 7 cm)
2
Side, left
(63,9 cm x 35 cm)
x
7
Back
(60,0 cm x 35,5 cm)
2
3
Side, right
(63,9 cm x 35 cm)
9
Drawer side, right/left
(35 cm x 12 cm)
10
Drawer back
(65 cm x 12 cm)
8
Drawer front
(67,7 cm x 18,9 cm)
x
x
3
x
3
6
6
Post
(70,9 cm x 4,4 cm)
350261-03
4x
12
11
Drawer bottom
(66,0 cm x 34,7 cm)
x
3
H-Profile
(56,0 cm x 1,7 cm)
2
Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Aa Ab
ø7.8 x 40mm Wooden dowel x
Ca
ø15 x 10.5mm Cam x
Fi
Back fitting w. ø3.5 x 15mm Screw x
Hk
M4 x 9mm Screw x
Ko
ø4,2 x 9,5mm Screw x
12
6
8
6
ø6 x 30mm Wooden dowel x
Cb
ø5 x 8, cc34mm Bolt x
Ge
6
ø27 x 24mm Metal Knob x
Jb
ø4 x 25mm Screw x
Sk
245 x 17 x 10mm Drawer runner x
16
12
12
Bp
ø3 x 35mm Screw x
1.2 x 15mm Nail xDi25
Hd
6
M4 x 20mm Screw x
Kb
ø5.8 x 8mm Screw x
Vl
6
44 x 23 x 23mm Angle x
12
6
18
2
Tools required
Phillips screwdriver
(Medium & large)
Flatblade screwdriver
(Medium)
Hammer
Ruler - Use this ruler to help correctly identify the screws
3
17060 16040 90 15013070 120100 14011050 803020100
350261-04
Assembly Instructions
Step 1
Assembly of the chest.
Step 1.1
Fix the posts 6 onto the
2
sides
screws
indicated.
The top of the posts
the sides
be ush.
and 3 using
Jb
into the holes
2
and 3 must
6
and
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
12
2
6
Jb
ø4 x 25mm Screw x
Jb
Jb
Jb
Jb
Jb
6
3
1
7
7
3
6
5
4
6
6
16
Jb
Jb
6
Jb
2
6
Jb
6
Step 1.2
Knock the dowels Aa
into the holes indicated
2
and 3.
2 and 3
on the sides
using a small hammer.
Screw the bolts Cb into
the holes indicated on the
sides
Aa
ø7.8 x 40mm Wooden dowel x
Cb
Cb
6
4
4
32
Cb
4
ø5 x 8, cc34mm Bolt x
3
Aa
Aa
2
2
Aa
Aa
350261-05
4
Assembly Instructions
Step 1.3
Slide the top of the
Sk
drawer runners
backwards. You can
identify the front end of
the drawer runner
the two M4 holes. See
details.
Fix the front end of the
drawer runners
2
sides
screws
and 3 using
Kb
through the
holes number 1 and 7 as
indicated.
See details.
Sk
Sk
to the
by
Kb
ø5.8 x 8mm Screw x
Kb
Hole no.
Hole no.
7
Front end
Kb
2
Sk
Kb
1
Kb
Sk
Sk
12
Front end
Front end
Sk
Sk
245 x 17 x 10mm Drawer runner x
Sk
Kb
Sk
Sk
Hole no.
Hole no.
Kb
1
6
7
Step 1.4
Slide the top of the draw-
Sk
er runners
Fix the back end of the
drawer runners
sides
2
screws
holes indicated.
See details.
forwards.
Sk
to the
and 3 using
Kb
through the
Note the hole!
Bottom end of
right hand side
Kb
2
Sk
Sk
Kb
Kb
3
Kb
ø5.8 x 8mm Screw x
6
Kb
Kb
Kb
Kb
Kb
3
5
350261-06
Assembly Instructions
Step 1.5
Fix the angles Vl using
Ko
screws
into the holes
indicated on the front
4
rail
.
Step 1.6
Knock the dowels Aa into
the holes indicated on
5
the back rail
using a
small hammer.
Step 1.7
Ko
ø4,2 x 9,5mm Screw x
Ko
Vl
Aa
Vl
4
44 x 23 x 23mm Angle x
Ko
Ko
2
Vl
4
Aa
ø7.8 x 40mm Wooden dowel x
Aa
2
5
Cb
Screw the bolts Cb into
the holes indicated on the
1
top
.
Step 1.8
Place the sides 2 and
3
onto the back rail 5.
Push cams
holes indicated on the
back rail
Arrows pointing towards
the sides
Turn the cams
right to x the sides
3
and
Ca
into the
5
.
2/3
.
Ca
to the
2
.
Cb
ø5 x 8, cc34mm Bolt x
Cb
Cb
Cb
4
1
Ca
ø15 x 10.5mm Cam x
2
3
2
350261-07
Ca
5
Ca
6
Assembly Instructions
Step 1.9
Place the top 1 onto the
2
sides
Push cams
holes indicated on the
sides
Arrows pointing towards
the top
Turn the cams
right to x the top
and 3.
2
and 3.
1
.
Ca
into the
Ca
to the
.
1
Ca
ø15 x 10.5mm Cam x
4
1
Ca
Ca
3
2
Step 1.10
Place the front rail
as shown.
Fix the angles
sides using screws
See detail.
Vl
to the
4
Ko
Ko
ø4,2 x 9,5mm Screw x
4
.
Ko
4
Ko
7
350261-08
Assembly Instructions
Step 1.11
Place the backs 7 into
the rabbet on the top
into the H-prole 12 and
onto the posts
Important!
Make sure the
!
angle between the
1
top
90° when the backs
attached.
Fix the backs
back rail
Use a small hammer.
and the posts 6 is
1
, the posts 6 and the
Di
.
6
7
to
5
using nails
1
.
7
is
the top
Distribute equally !
1.2 x 15mm Nail xDi24
1
12
Di
1
7
1
6
7
5
6
Step 2
Assembly of the drawers.
Step 2.1
Fix the drawer sides 9
10
to the drawer back
shown, using screws
as
Bp
8
12
Bp
x
9
x
3
3
10
11
9
Bp
ø3 x 35mm Screw x
.
10
9
Bp
9
350261-09
8
Assembly Instructions
Step 2.2
Knock the dowels Ab
into the holes indicated
on the drawer sides
9
using a smal hammer.
Step 2.3
Slide the drawer bottom
11
into the drawer
9
sides
.
Ab
ø6 x 30mm Wooden dowel x
12
9
Ab
x
9
Ab
3
9
9
Step 2.4
Screw the bolts Cb into
the holes indicated on
8
the drawer front
.
Step 2.5
Push the drawer front 8
9
onto the drawer sides
Place cams
Ca
into the
holes indicated. Arrow
pointing towards the front.
Ca
Turn the cams
to the
right to x the front.
.
Cb
11
x
3
Cb
ø5 x 8, cc34mm Bolt x
Cb
6
8
x
3
Ca
ø15 x 10.5mm Cam x
6
8
Ca
9
Ca
x
9
9
3
350261-10
Assembly Instructions
Step 2.6
Important!
Make sure the
!
angle between
8
the drawer front
the drawer sides
before the drawer bottom
11
is xed using Fi as
shown.
To adjust the angle between
the drawer sides and the
fronts push the tting
sidewards. See details.
and
9
is 90°
Fi
Step 2.7
Fix the metal knobs Ge to
8
the drawer front
Hd
screws
.
using
Fi
8
11
9
Ge
ø27 x 24mm Metal Knob x
Ge
Fi
10
Fi
Back fitting w. ø3.5 x 15mm Screw x
6
9
90°
x
3
Fi
Fi
Hd
6
M4 x 20mm Screw x
6
Fi
Step 2.8
Pull out the drawer
runners. Slide the
drawers onto the runners.
Fit and x the lower
drawer rst and work your
way up.
Fix drawers to the drawer
Hk
runners using screws
.
Ge
Hd
8
Hk
Hd
Hk
M4 x 9mm Screw x
x
3
6
Hk
350261-11
10
Loading...