Page 1
Aubrey - 3ft Bed
Assembly Instructions- Please keep for future reference
531/3826
553/2975
745/2424
765/7236
Dimensions
Length - 200,5cm
Width - 106,2cm
Height - 110cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, ca l l t h e customer Helpline: 03456 400 800
Issue 11 - 26/05/20
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
.
Check you have all the
components and tools listed on
pages 2 and 3.
.
Remove all fittings from the
plastic bags and separate them
into their groups.
.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
.
Make sure you have enough
space to layout the parts before
starting.
.
Do not stand or put weight on
the product, this could cause
damage.
.
Assemble the item as close
to its final position (in the same
room) as possible.
.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
. This product contain natural
timber. You may notice some
variation in the grain and
colour of different component
parts which is normal for
furniture produced using
natural wood and is not the
result of any manufacturing
fault.
.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
.
Parts of the assembly will be
easier with 2 people.
.
Dispose of all packaging
carefully and responsibly.
We do not
care and maintenance
.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
1
.
From time to time check
that there are no loose
screws on this unit.
.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Panels
Please check you have all the panels listed below
Headboard (106,2 x 110,0cm)
01
Footboard (106,2 x 60,0cm)
02
Side rails x 2 (190,0 x 11,5cm)
03
Slats x 13 (91,5 x 6,8cm)
04
2
Page 4
If you have damaged or missing components,
Components - Fittings
call theCustomer Helpline: 03456 400 800
Please check you have all the fittings listed below
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
90mm Bolt 1/4 x 04
D
40mm Wooden dowel x 04
G
Spanner x 01
J
Spacer 84mm x 02
B
Half-Moon Nut 1/4 x 04
E
35mm Screw x 26
H
Nut 1/4 x 04
C
Allen key x 01
F
Washer 1/4 x 04
I
70mm Headless Bolt 1/4 x 04
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler- Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Page 5
Assembly Instructions
Step1
Fitting dowels
Insert dowels
D
into the indicated parts.
D
D
03
03
D
D
D
Step 2
Assembling side rails
Screw headless boltA:
to footboard as shown.
02
Do not over tighten.
B: Insert washer to
side rails and fit
03
F
footboard to side rails.
Fix headless bolts using
H
nuts and spanner .
I
the
I
G
A:
B:
02
F
I
50mm
I
Do not over tighten the bolts,
see indicative measure.
G
G
F
H
H
03
03
02
4
Page 6
Assembly Instructions
Step 3
Assembling side rails
Attach side rails to
the headboard. Insert
Half moon nut into
side rails as shown.
03
03
B
B
B
Then fix them to the
headboard using
bolts and allen key .
A
01
C
Step 4
Fixing slats
Using spacer ,
centralize slats in bed
frame prior to fixing. Fix
slats using screws , as
shown.
Fix slats in one side first,
then fix them in the other
side by pushing the rail
against the slats if
necessary.
J
E
01
B
03
B
03
C
A
C
A
J
E
E
J
J
E
J
Periodically check that
all screws are tight.
04
5
Page 7
Assembly Instructions
Step 5
Additional step to fixing
slats
Make sure that
s slats screws
never collide to the
screws on the slats
support bar, as shown
in the diagram.
Warning!
collide.
Assemble is complete!
6
Page 8
77
Loading...