Argos 796/4699, 764/5554 User guide

Hallingford Gloss - 3 Drawer Dressing Table

Assembly Instructions - Important: Retain these instructions for

future reference

CR

CR

796/4699

764/5554

CR

WARNING!

In order to prevent overturning, this product must be used

with the 2 wall attachment devices provided

Dimensions

Width - 119.9cm

Depth - 41.1cm

Height - 79.5cm

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0330 016 1114
For any other queries please contact the Customer Helpline on: 0345 640 2020

More help is available throughout this

booklet by scanning in the QR codes or

typing in the links

MADE IN

BRITAIN

Issue 8 - 10/08/20

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 44kgs.
Please lift with care.

• Assembly to be carried out by
a competent adult only.

• Check you have all the
components and tools listed on
pages 1 to 3 for the Dressing
Table and pages 22 to 23 for
the Stool.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• During assembly children
should be kept away from the
product due to possible risk of
injury.

• Installation shall only be
carried out exactly according to
the manufacturer’s instructions

- otherwise a safety risk can
occur if incorrectly installed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2overbalance
protector kits supplied.

• Dispose of all packaging
carefully and responsibly.

• Do not use this item if any
components are missing or
damaged.

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• Regularly check all fastenings
to ensure that they are properly
tightened.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Components - Panels for Dressing Table

If you need help or have damaged or missing parts, please refer to page 2

Please check you have all the panels listed below

2 Top

1

(DF-00013063)

(119.9 x 39.6cm)

2 Small Cross Rail

(32.1 x 9.2cm)

x 2

(DF-00018009)

Components - Panels for Dressing Table

Please check you have all the panels listed below

3 Left Side

(76.7 x 39.4cm)

(DF-00013110)

7 Left Divider

(DF-00018004)

(16.7 x 35.75cm)

4 Right Side

(76.7 x 39.4cm)

(DF-00013111)

8 Right Divider

(DF-00018005)

(16.7 x 35.75cm)

5 Top Modesty

(115.9 x 19.2cm)

(DF-00018002)

6 Bottom Modesty

(115.9 x 19.2cm)

Mirror - MIR-00000011
(54.8 x 48.4cm)
Safety Back SAR

2

(DF-00018013)

10 Left Drawer

Front

(DF-00018045)

(33 x 16.2cm)

14 Deep Drawer

Back

(W271-130)

(27.1 x 13cm)

x 2

17 Narrow Left Drawer

Side

(WD350-95LH)

(35 x 9.5cm)

11 Right Drawer

Front

(DF-00018046)

(33 x 16.2cm)

15 Deep Drawer

Base

(T282-347)

(28.2 x 34.7cm)

x 2

18 Narrow Right Drawer

Side

(WD350-95RH)

(35 x 9.5cm)

9

Mirror Back (DF-00018003)

(59.5 x 66.2cm)

12 Deep Left Drawer

Side

(WD350-130LH)

(35 x 13cm)

x 2

16 Centre Drawer

Front

(DF-00018047)

(48.7 x 12.2cm)

19 Narrow Drawer

Back

(W436-95)

(43.6 x 9.5cm)

13 Deep Right Drawer

Side

(WD350-130RH)

(35 x 13cm)

x 2

20 Narrow Drawer

Base

(T447-347)

(44.7 x 34.7cm)

2

Components - Fittings for Dressing Table

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Bag 1

A

Metal dowel (F901) x 20

E

45mm Screw

(F65) x 3

I

Connecting Sleeve

(F432) x 2

B

Large locking cam

(F900) x 20

nut

F

(F63) x 6

Strap

J

Overbalance protector kit (F269) x 2

C

Wooden dowel (F22) x 20

G

9mm Screw (F73) x 18

Screw

Washer x 2

Bag 2

A L

Metal dowel (F901) x 6

F

13mm Screw

(F63) x 12

K

Small locking cam

(F3) x 6

nut

D

Plastic Nail

H

9mm Screw

19mm

Screw (F461) x 4

(F91) x 4

(F74) x 213mm Screw

Knock-in Peg

(F171GY) x 12

Individual Fittings Bags

a

O

O

O

O

b

c

d

CL

DL

NM

Wedgefix

350mm long

CL Runner

(F639) x 6

(F422) x 3

CR Runner (F424) x 3

DL Runner (F425) x 3

DR Runner

(F426) x 3

Ruler - Use this ruler to help
correctly identify the screws

mm 10 20 30 40 50 60 70 80

P

CR

Handle

(F306) x 2

Tools required

Scissors • Rule • Hammer • Spirit level •
Flat-head screwdriver • Bradawl•

DR

Cross-head screwdriver
Eye protection (when using a hammer or drill)
Electric drill (only use when drilling into walls)

3

Assembly Instructions

Step 1

Prepare the left side

a: Fit a CL runner

to the left side .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

G

up with the other panel
holes.

b: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

Insert 2 large locking
cam nuts into the left
side .

Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.

O a

F

B

3

O a

3

G

Let’s assemble the Dressing Table carcase first

Fixing Bottom Mounted Runners

hps://www.youtube.com/watch?v=Z6lGMy19h7Q

1st

front edge

Finished

a:

front edge

Finished

G

screw

Finished

front edge

Bradawl

O a

O a

CL

G

G

G

CL

O a

3

B

B

Tap 2 wooden dowels
into the left side .

C

3

Note: Wooden dowels

must not stick out from
the edge by more than
10mm or they may
damage other panels.

c: Screw 5 metal dowels

. into the left side .

A

Note: Tighten the metal
dowels up fully against
the panels.

3

b:

c:

Finished

front edge

Finished

front edge

F

CL

3

A

A

A

CL

A

3

CL

C

B

C

10mm

C

A

A

4

Assembly Instructions

Step 2

Prepare the top
modesty and bottom
modesty

Tap 4 wooden dowels
into the top modesty
and the bottom modesty
. .

6

Insert 4 large locking
cam nuts into the top
modesty and the

B

5

bottom modesty .

C

5

6

B

C

C

C

C

B

5

B

B

Finished

front edge

6

B

B

C

C

B

B

Step 3

Fit the 2 modesty panels to
the left side

Push the top and bottom
modesty panels and
. down onto the left

6

side .

3

Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to each modesty
panel and .

5 6

Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.

5

B

B

B

Finished

front edge

C

C

Finished

front edge

A

5

6

CL

3

The top edge of the

top modesty must be

ush with the top

edge of the left side

5

Assembly Instructions

Step 4

Prepare the right side

a: Fit a CR runner

to the right side .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

G

up with the other panel
holes.

b: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

Insert 2 large locking
cam nuts into the
right side .

O b

F

B

4

O b

4

G

a:

1st
screw

O b

CR

G

G

G

CR

4

B

O b

Finished

front edge

B

F

C

G

C

front edge

Finished

Tap 2 wooden dowels
into the right side .

4

c: Screw 5 metal

dowels into the right
side .

A

4

C

b:

4

A

A

A

A

c:

4

CR

Finished

front edge

A

CR

Finished

front edge

Bradawl

O b

front edge

Finished

6

Assembly Instructions

Step 5

Fit the right side

Push the right side
down onto the modesty
panels and .

5 6

Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to each modesty
panel and .

5 6

4

B

Note: Support the right side
until you lay the assembly
down in the next step.

4

5

6

CL

Step 6

Lay the unit down

Carefully lay the unit
down onto its back.

Warning: The
unit is heavy.
Lift with care.

7

CL

Assembly Instructions

Step 7

Prepare the left divider

a: Fit a CL runner

to the left divider .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

G

up with the other panel
holes.

b: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

O a

F

c: Insert 2 large locking

cam nuts into the left
divider .

B

7

O a

7

G

1st

front edge

Finished

Finished

front edge

G

screw

O a

CL

G

G

G

CL

O a

a: b:

7 7

B

Finished

front edge

CL

C

B

c:

7

Finished

front edge

C

front edge

Finished

Bradawl

O a

F

CL

Tap 2 wooden dowels
into the left divider .

C

7

Turn the divider over

d: Fit a CR runner

to the left divider .

The 1st screw uses

O b

7

G

the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

G

up with the other panel
holes.

e: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

Screw a metal dowel
into the left divider .

O b

F

A

7

Turn the divider over

1st
screw

O b

CR

G

G

d: e:

O b

7

G

G

CR

front edge

Finished

Finished

front edge

Bradawl

front edge

Finished

O b

A

F

7

CR

Finished

front edge

8

Assembly Instructions

Step 8

Prepare the 2 small cross
rails

Tap 2 wooden dowels

C

into each of the 2 small
cross rails .

2

Insert 2 large locking
cam nuts into each of
the 2 small cross rails .

B

2

Step 9

Fit a small cross rail to the
left divider

Push a small cross rail
down onto the left
divider .

7

Use a screwdriver to
tighten the large locking
cam nut fitted to the
small cross rail .

B

2

2

B

C

2

2

CR

front edge

7

B

Finished

Finished

front edge

Finished

front edge

x 2

C

Step 10

Fit the small cross rail and
left divider

Push the small cross rail
. onto the left side .

2 3

Use a screwdriver to
tighten the large locking
cam nut fitted to the
small cross rail .

9

B

2

Finished

front edge

CL

2

3

CL

Assembly Instructions

Step 11

Prepare the right
divider

a: Fit a CR runner

to the right divider .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws

G

. use the holes that line
up with the other panel
holes.

b: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

O b

F

O b

8

G

1st
screw

O b

CR

a: b:

G

G

G

O b

8 8

B

G

CR

B

front edge

Finished

Finished

front edge

C

Bradawl

front edge

Finished

O b

F

CR

Finished

front edge

C

c: Insert 2 large locking

cam nuts into the
right divider .

Tap 2 wooden dowels
into the right divider .

Turn the divider over

d: Fit a CL runner

to the right divider .

The 1st screw uses
the 1st hole in from the
front of the runner.

The 2nd and 3rd screws
. use the holes that line

G

up with the other panel
holes.

B

8

C

8

O a

8

G

e: Mark the top hole of

the runner with a
bradawl and then fit a
screw .

O a

F

c:

front edge

Finished

d:

8

G

Finished

front edge

CR

Finished

front edge

Turn the divider over

1st
screw

O a

CL

G

G

G

CL

O a

8

front edge

Finished

front edge

Bradawl

Finished

O a

A

F

Screw a metal dowel
into the right divider .

A

8

e:

CL

8

10

Assembly Instructions

Step 12

Fit a small cross rail to the
right divider

Push a small cross rail
down onto the right
divider .

8

Use a screwdriver to
tighten the large locking
cam nut fitted to the
small cross rail .

B

2

Step 13

Fit the small cross rail and
right divider

Finished

front edge

Finished

front edge

2

2

CL

8

CL

Finished

CL

front edge

Push the small cross rail
. onto the right side .

2 4

Use a screwdriver to
tighten the large locking
cam nut fitted to the
small cross rail .

B

2

Step 14

Prepare the top

Screw 8 metal dowels
into the top .

1

A

CL

2

4

A

A

A

A

Finished

front edge

A

11

A

1

A

A

Assembly Instructions

Step 15

Fit the top

Push the top onto
the assembly.

Use a screwdriver to
tighten the 8 large
locking cam nuts
fitted to the left side ,
right side , left divider
. and right divider .

7 8

1

B

3

4

Finished

front edge

CL

CL

3

7

1

8

CL

4

Step 16

Fit the 4 plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

4

Carefully stand the unit up
for the next step.

Warning: The
unit is heavy.
Lift with care.

D

3

CL

CL

3

D

CL

D

4

D

D

12

Assembly Instructions

Step 17

Fit the mirror back

From the front of the unit,
push the 2 connecting
sleeves through the
holes in the top modesty

5

. and then locate them
into the holes in the mirror
back .

From the rear of the mirror
back , insert the screws
into the connecting
sleeves and rmly
tighten them up.

I

9

9

I

H

Warning:
Glass! Handle
with care

9

H

H

5

CR

CR

I

CR

I

Step 18

Secure the mirror back

Secure the mirror back to
the back edge of the top
using the 3 screws .

1

E

9

Warning:
Glass! Handle
with care

E

E

E

9

CR

CR

1

CR

13

Assembly Instructions

Step 19

Fit the 2 overbalance
protector kits

To prevent possible
overbalancing this unit
must be secured to a
suitable wall by tting of
the 2 overbalance
protector kits to the unit

Wall xings are not
supplied as they will need
to suit the wall type.

Take care when

Note:

drilling the wall that you
do not drill into any pipes,
wires etc.
If in doubt, consult an
expert.

J

In order to prevent overturning

this product must be used with the 2

wall attachment devices provided

WARNING!

Top Modesty Panel

Wall xing

(not supplied)

Example

Washer

Screw

J

Washer

Screw

(not supplied)

See the next page for a guide to
wall mounting and xings

CR

J

CR

J

CR

14

A Guide to Wall Mounting & Fixings

Important note:

If plastic wall plugs
are supplied with your
product:

- these are only suitable for
use in masonry walls.

If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.

Failure of the product due to
using incorrect fixings is the
responsibility of the installer.

Important: When drilling into walls always
check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.

Types of walls

You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.

No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug

Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.

No.2 “Plasterboard” wall plug

For use with plasterboard partitions or
hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.

No.6 “Shield Anchor” wall plug
Heavy loads

For use when attaching light loads on
to plasterboard partitions.

Care &
Maintenance

15

For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.

Safety: Always check the fitting
and location to ensure your safety
in and around the home.

For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.

Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

Assembly Instructions

Step 20

Prepare the left and
right drawer fronts

Screw 2 metal dowels
into both the left drawer
front and the right

10

drawer front .

Note: Tighten the metal
dowels up fully against
the panels.

11

A

Step 21

Prepare the 2 sets of
deep drawer sides

Insert a small locking
cam nut into the deep
left drawer sides and
deep right drawer sides

13

. .

K

12

Now assemble the drawers for the Dressing Table

Drawer Assembly

www.youtube.com/watch?v=InNBV_uuMmo

Note: The small right
drawer front has a small
identification hole.

A

A

A

10

K

12

A

K

A

11

13

K

Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.

Step 22

Attach the deep
drawer sides to the
left and right drawer
fronts

Push the deep left
drawer side . and
deep right drawer side .
onto the back of the left
and right drawer fronts
. and .

10 11

Turn the small locking
cam nuts on the deep
left drawer side and
deep right drawer side .

12

13

K

12

13

x 2

12

x 2 x 2

K

13

10 11

A

Note: Turn the locking
cam nuts clockwise
to secure panels - more
than 1/2 a turn.

K

16

Assembly Instructions

Step 23

Fit the deep drawer
bases

Slide the deep drawer
base down into the

15

grooves in the deep
drawer sides and
and down into the
groove in the left drawer

10

front and right
drawer front .

12 13

11

Step 24

Fit the deep drawer
backs

12

15

4

13

10 11

x 2

M

Fit the deep drawer back
. between the deep

14

drawer sides and .
Make sure that the deep
drawer base fits into
the groove in the deep
drawer back .

Hold the deep drawer
back in position and

14

tap the knock-in pegs
through the holes in the
deep drawer sides
and .

14

12 13

15

14

M

13

Step 25

Fit the handles

Attach a handle to the
left and right drawer front

10 11

. and using screws

L

. .

P

M

M

M

14

413

15

12

x 2

L

L

x 2

P

10 11

Step 26

Fit the wedgefixes

Turn the 2 deep drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

17

Important: Make sure
that the drawer assembly

x 2

N

N

N

is square before fitting
the wedgefixes.

N

Assembly Instructions

Step 27

Fit runners to the
drawers

Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer

10 11

front and . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .

Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.

O c

12

F

O d

13

Fixing Bottom Mounted Runners

hps://www.youtube.com/watch?v=Z6lGMy19h7Q

Bradawl

Runners must be

pushed up against

the drawer front

DL

Bradawl

F

F

F

10 11

F

13

DL

12

O c

x 2

Bradawl

DR

O d

Step 28

Prepare the centre
drawer front

Screw 2 metal dowels

A

into the centre drawer
front .

16

Step 29

Prepare the narrow
drawer sides

Insert a small locking
cam nut into the
narrow left drawer side

17

. and narrow right
drawer side .

K

18

A

A

16

K

17

K

18

K

Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.

18

Assembly Instructions

Step 30

Attach the narrow
drawer sides to the
centre drawer front

Push the narrow left
drawer side and
narrow right drawer side
. onto the back of the

18

centre drawer front .

Turn the small locking
nuts on the narrow

K

left drawer side and
narrow right drawer side
. .

18

17

17

16

16

17

18

K

A

B

Step 31

Fit the narrow drawer
base

Slide the narrow drawer
base down the

20

grooves in the narrow
drawer sides and

17 18

and down into the
groove in the centre
drawer front .

16

Step 32

Fit the narrow drawer
back

Fit the narrow drawer
back between the

19

narrow drawer sides
and .

18

Make sure that the
drawer base fits into

20

the groove in the narrow
drawer back .

19

17

17

M

M

20

18

16

M

M

19

18

20

17

Hold the narrow drawer
back in position and

19

tap the knock-in pegs
through the holes in the
narrow drawer sides

18

and .

19

M

17

Assembly Instructions

Step 33

Fit the wedgefixes

Turn the narrow drawer
assembly over and slide
2 wedgefixes into the

N

front and back grooves,
as shown, and tighten up
the screws.

Step 34

Fit runners to the
drawer

Fit the DL runner to
the bottom edge of the
narrow left drawer side
as shown, making sure
that it is pushed up
against the back of the
centre drawer front .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .

O c

17

16

F

Bradawl

Bradawl

N

Runners must be

pushed up against

the drawer front

N

F

16

17

Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.

N

F

F

F

DL

18

Bradawl

DR

Fit the DR runner to

O d

the bottom edge of the
narrow right drawer side

18

. using the same
method.

DL

O d

O c

20

Assembly Instructions

Step 35

Fit the drawers

Slide the wheels of the
runners tted to the
drawers, over the wheels
of the runners tted to the
side panels and push the
drawers into position.

Fixing Bottom Mounted Runners

h�ps://www.youtube.com/watch?v=Z6lGMy19h7Q

Panel

Drawer

CR

CR

CR

Step 36

21

CR

CR

CR

The Dressing Table

assembly is complete

Please remove any blue protective lm from

panel edges and clear protective lm from panel

surfaces and clean the mirror

Components - Panels for Stool

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Please check you have all the panels listed below

21 Stool Left Side

(39.6 x 34.9cm)

24 Stool Cross Rail

(46.8 x 6cm)

26 27 Stool Left Drawer

Stool Drawer Front (DF-00013113)

(46.2 x 12.2cm)

(DF-00013090)

(DF-00013089)

x 2

22 Stool Right Side

(39.6 x 34.9cm)

25 Stool Back Rail

(46.8 x 12.8cm)

Side

(W300-95LH)

(30 x 9.5cm)

x 2

(DF-00013093)

(DF-00013091)

23 Stool Top

(51 x 35.3cm)

(DF-00013088)

28 Stool Right Drawer

Side

(W300-95RH)

(30 x 9.5cm)

29 Stool Drawer Base

(44.7 x 29.7cm)

(T447-297)

30 Stool Drawer Back

(43.6 x 9.5cm)

(W436-95)

Seat Pad (FHALPAD)

31

(458 x 300mm)

22

Components - Fittings for Stool

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Main Fittings Bag

A

Metal dowel (F901) x 12

D

Plastic Nail

(F91) x 4

B

Large locking cam nut

G

9mm Screw (F73) x 4

Drawer Fittings Bag marked ‘drw kit’

A

Metal dowel (F901) x 2

L

Screw (F461) x 2

19mm

H

9mm Screw

M

Knock-in Peg

(F74) x 2

(F171GY) x 4

(F900) x 12

C

Wooden dowel (F22) x 16

Q

32mm Screw

K

Small locking cam nut

(F3) x 2

N

Wedgex (F639) x 2

(F72) x 4

Individual Fittings Bags

P

Handle (F306) x 1

R

Drawer runner (F1004) x 2

CL

278mm long

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

23

Assembly Instructions

Step 37

Prepare the stool left side

a: Place a runner on

the stool left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .

b: Slide the runner back

the other way and fit the
2nd screw into the
corresponding hole in
the stool left side .

G

c: Screw 4 metal dowels

into the stool left side
.

R

21

G

21

A

21

Let’s assemble the Stool carcase

Fitting Ball Bearing Runners

www.youtube.com/watch?v=yG4x�JJeSg

G

R

G

R

a:

21

d: Insert 2 large locking

cam nuts into the
stool left side .

Tap 2 wooden dowels
into the stool left side
.

B

21

C

21

b:

c:

21

21

G

A

A

A

A

d:

21

B

C

B

C

24

Assembly Instructions

Step 38

Prepare the stool right side

a: Place a runner on

the stool right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .

b: Slide the runner back

the other way and fit the
2nd screw into the
corresponding hole in
the stool right side .

G

c: Screw 4 metal dowels

into the stool right side
.

R

22

G

22

A

22

a:

22

G

R

G

R

G

D: Insert 2 large locking

cam nuts into the
stool right side .

Tap 2 wooden dowels
into the stool right side
. .

22

B

22

C

b:

c:

22

22

A

A

A

A

25

d:

22

B

B

C

C

Assembly Instructions

Step 39

Prepare the 2 stool back
rails

Tap 2 wooden dowels
into each of the 2 stool
back rails .

25

C

C

B

B

B

B

25

Insert 4 large locking
cam nuts into each of
the 2 stool back rails .

B

25

Step 40

Fit a stool back rail to the
stool right side

Push a stool back rail
down onto the stool right
side .

22

Use a screwdriver to
tighten the 2 large locking
cam nuts fitted to the
2 stool back rail .

B

25

25

Step 41

x 2

C

The top edge of the

stool back rail must be

ush with the top

edge of the left side

25

22

Fit the other stool back rail

Push a stool back rail
down onto the stool right
side .

22

Use a screwdriver to
tighten the 2 large locking
cam nuts fitted to the
2 stool back rail .

B

25

25

Step 42

Prepare the 2 stool cross
rails

Tap 4 wooden dowels
into each of the 2 stool
cross rails .

24

C

25

22

C

C

Finished

front edge

24

x 2

C

C

26

Assembly Instructions

Step 43

Fit the 2 stool cross rails

Push the 2 stool cross

24

rails down onto the
stool right side .

22

Step 44

Fit the left side

Finished

front edge

24

24

Finished

front edge

22

Push the left side

21

onto the assembly.

Use a screwdriver to
tighten the 2 large locking
cam nuts fitted to each

B

of the 2 stool back rails
. .

25

Step 45

Fit the 4 plastic nails

Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .

22

D

21

21

25

25

21

D

D

Carefully stand the unit up
for the next step.

27

D

D

22

Assembly Instructions

Step 46

Prepare the stool top

Screw 4 metal dowels
into the stool top .

A

23

Step 47

Fit the seat pad to the stool
top

Fit the seat pad to
the stool top using 4
screws .

Q

Note: Make sure that
you screw into the hard
surface of the seat pad.

31

23

A

A

A

A

23

31

Q

Q

23

Q

Soft
surface

Q

Hard
surface

Step 48

Fit the stool top

Push the stool top
down onto the stool
sides and .

21 22

Use a screwdriver to
tighten the 4 large
locking cam nuts
fitted to the stool sides
. and .

21 22

23

B

23

22

21

28

Assembly Instructions

Step 49

Prepare the stool drawer
front

Screw 2 metal dowels

A

into the stool drawer
front .

26

Step 50

Prepare the stool drawer
sides

Insert a small locking
cam nut into the stool
left drawer side and
stool right drawer side .

K

27

28

Now assemble the drawer for the Stool

A

A

26

K

27

K

28

Step 51

Attach the stool drawer
sides to the stool drawer
front

Push the stool left drawer
side and stool right

27

drawer side onto the

28

back of the stool drawer
front .

26

Turn the small locking
nuts on the stool left

K

drawer side and stool
right drawer side .

27

28

Step 52

Fit the stool drawer base

Slide the stool drawer

29

base down the
grooves in the stool
drawer sides and
and down into the
groove in the stool
drawer front .

27 28

26

27

27

28

26

29

28

26

29

Assembly Instructions

Step 53

Fit the stool drawer back

Fit the stool drawer back

30

. between the stool
drawer sides and .
Make sure that the stool
drawer base fits into
the groove in the stool
drawer back .

Hold the stool drawer

30

back in position and
tap the knock-in pegs
through the holes in the
stool drawer sides

28

and .

27 28

29

30

27

M

27

M

M

M

M

30

28

29

Step 54

Fit the handle

Attach a handle to the
stool drawer front
using screws .

P

26

L

Step 55

Fit the wedgexes

Turn the stool drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.

N

L

L

26

P

N

N

30

Assembly Instructions

Step 56

Fit the stool drawer

Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .

Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.

Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.

27 28

R

H

H

R

Fitting Ball Bearing Runners

www.youtube.com/watch?v=yG4x�JJeSg

H

H

27

Warning: Use a screwdriver
to position the runners as
they could have sharp edges.

28

H

R

2nd threaded

hole

Step 57

The Stool

assembly is complete

Please remove any blue protective

film from panel edges and clear

protective film from panel surfaces

31 ALR3436