Argos 7389786, 7389810, 7389841 ASSEMBLY INSTRUCTIONS

Triple Bunk Bed
Important - Please read these instructions fully before starting assembly
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 -15/12/09
656/2982
Assembly Instructions - Please keep for future reference
656/3905
656/3912
Width - 142.5cm
Height - 170cm
Important - Please read these instructions fully before starting assembly
Mattress height safety notice
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 20cm:The top of the mattress shall not come above the line marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are loose.
5) Recommended size of the mattress for the top bunk is 90×190cm.For the lower bed is 135×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) The upper bed of bunk beds are not suitable for children under six years due to the risk of injury from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2007
1
Safety and Care Advice
!
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Place the product on flat and steady surface during use.
• Keep these instructions for future use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only upon completion of the assembly should all fixing points be fully tightened.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level
surface to avoid damaging the unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Safety: To avoid any risk of suffocation to animals or children dispose of the plastic bags immediately.
• Cleaning: As with all surfaces clean with a damp cloth and mild detergent, do not use bleach or abrasive products.
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Please check you have all the parts listed below
1
Components - Parts
2
Rear post x 2
(4.5 x 170cm)
2
Front post x 2 (4.5 x 170cm)
3
Ladder frame x 2 (2.2 x 109cm)
4
End panel x 2 (97 x 39.8cm)
5
Lower stretcher x 2 (3 x 133.7cm)
6
Front guard (191 x 42cm)
7
Rear guard (191 x 42cm)
8
Lower side rail (rear) (191 x 7.3cm)
9
10
Top bunk slats x 24 (1.6 x 95cm)
11
Lower bed slats (with hole) x 3(1.6 x140cm)
12
Lower bed slats x 14 (1.6 x 140cm)
13
Central support (1.6 x 191cm)
14
Legs x 3 (1.6 x 23.5cm)
15
Ladder rungs x 5 (2.2 x 30.5cm)
Lower side rail (front) (191 x 7.3cm)
Extra brackets
Loading...
+ 7 hidden pages