22-06-2017_JTJA:
Kopi af 71946 - Oprettet af CSR
Canterbury 4 DR 2 DRW ROBE
Assembly Instructions - Please save for future reference
737/8876
724/5882
736/6503
kg
25
lbs
55
kg
30
lbs
66
Dimensions
Width: 201.3cm
Depth: 62.7cm
max.
kg
20
lbs
44
kg
9
lbs
20
Height: 202.1cm
Important – Please read these instructions carefully before starting the assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
71946 Version A Date 27/06/2017
Safety and Care Advice
Important – Please read these instructions carefully before starting the assembly
• Check that you have all the
components and tools listed on
the following pages.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area - small
parts can choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting.
Care and maintenance
• Only clean the unit using a
damp cloth and mild detergent.
Do no use bleach or abrasive
cleaners.
• During assembly, do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close to
its intended placement (in the
same room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will
be easier with 2 people to
complete.
• From time to time, check to
see if screws have become
loose. If so, please tighten them
again.
• We do not
recommend the use
of power drivers for
inserting screws, as
this could damage
the unit. Please only use hand
screw drivers.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Safety
• The provided tip-over restraint
must be installed in order to
ensure user safety.
Note: If required, the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
If you have damaged or missing components, call the
Components - Panels
Customer Helpline: Argos = 0345 6400800
Please check that you have all the panels as listed below
00734
Left drawer side
(45 x 14cm) x2
76428
Profile side
(62 x 2.5cm) x2
00733
Right drawer side
(45 x 14cm) x2
(201.5 x 48.9cm) x2
EE
Drawer front
Profile front (200.5 x 4cm) x2
76460
76427
Profile side
(96.7 x 22.1cm) x2
03336
(62 x 2.5cm) x2
Drawer back
(92.2 x 14 cm) x2
T
Loose
(46.9 x 57.9cm) x4
shelf
FA Side panel
Back panel
09790
Large drawer bottom
(198.8 x 58cm) x2
Back panel (201.5 x 96.9cm)
09791
07165
(93.3 x 44.7cm) x2
Frame door (191.7 x 48.2cm)
18743
UB
Large f
(95.5 x 57.9cm) x1
ixed shelf
Frame door (191.7 x 48.2cm)
18744
UC
Small f
(47 x 57.9cm) x4
Frame door (146.9 x 48.2cm) x2
18732
ixed shelf
ID Bottom / Top panel
GB
Divider panel (198.8 x 58cm) x2
(201.3 x 62.4cm) x2
3
Components - Fittings
Please check that you have all of the ttings listed below
Note: The quantities listed in the following are the correct amount to complete the assembly.
In some cases, more ttings may be supplied than required.
10601
Holder x6
20203
Dowel (ø5 x 30mm) x24
25215
Flat head screw
(ø3 x 12mm) x6
26020
Flat head screw
(ø5.8 x 9mm) x8
26214
Machine screw
(M4 x 9mm) x4
33204
Wedges x4
11042
Shelf support x16
20228
Drawer fastener x8
25233
Flat head screw
(ø3.5 x 15mm) x4
26033
Flat head screw
(ø6.3 x 27mm) x22
26232
Machine screw
(M4 x 23mm) x8
50491
Hinge plate x14
11229
Bracket x20
23006
25 pcs
Nail x4
25440
Screw
(ø4 x 13mm) x8
26071
Screw (ø7 x 8mm) x28
31513
Cam bolt x4
52291
Hinge x14
11230
Screw (ø5 x 7.5mm) x20
23010
Big nail x36
25610
Connector bolt
(ø7 x 50mm) x24
26211
Machine screw
(M4 x 7mm) x14
31687
Cam x4
63008
Floor glider x8
81040
Handle x8
97642
Allen key x1
72501
Hanger x2
72509
Hanger x1
10503
Drawer bottom support x2
91410
Lock bracket x1
41421
Drawer runner x4
Strap x2
9620394009
Stop x8
4
Tools required
Cross head screwdriver
Wooden block
(medium & large)
Flathead screwdriver
Books X6
(medium)
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
Ruler
Tape measure
Ruler - Use this ruler to help correctly identify the screws
Hammer
Eye protection
(when using a
hammer or glue)
5
(x2)
(x2)
Assembly Instructions
Step 1
Insert dowels
Insert dowels 20203
into outer holes on the
ends of side panel FA
and GB .
On FA , attach holders
10601 while using at
head screws 25215 .
Fittings you will need for this step:
Dowel
#20203 x16
Holder
#10601 x2
Flat head screw
#25215 x2
(x2)
(x2)
Step 2
Attach holders
Attach holders 10601 with
at head screws 25215 on
the divide panels GB .
Please note where to
place the holders on the
sides of the panels respectively.
Fittings you will need for this step:
Holder
#10601 x4
Flat head screw
#25215 x4
6
Assembly Instructions
Step 3
Fittings you will need for this step:
Attach hinge plates
Fixate each hinge plate
50491 with screws
26071 .
Insert machine screws
26211 in the center of
the hinge plates.
Please note in which
hole rows to place place
the hinge plates when
mounting on the panels.
Screw
#26071 x28
Machine screw
#26211 x14
31
30
Hinge plate
#50491 x14
32
31
34
33
15
14
1
FA
31
GB GB
11
10
32
3130
11
10
34
33
FA
15
14
1
7
1
8
GB
GB
47
GB
GB
Assembly Instructions
z
Step 4
Attach 4 screws 11230
on one side of both divider panels GB . Then
turn boft divider panels
over and attach 2 screws
11230 on each of the
other sides.
Please note the hole
rows as pictured for correct assembly.
Fittings you will need for this step:
Screw
#11230 x12
GB
47
GB
GB
GB
Step 5
Attach 4 screws 11230
on each side panel FA .
Fittings you will need for this step:
Screw
#11230 x8
47
8
1
FA
FA
8
1
8
# $PRPVIEW:{Pos_Beslag}
x8
# 41421
x4
# 26020
x8
# 25233
x4
?
# $PRPVIEW:{Pos_Beslag}
x8
# 41421
x4
# 26020
x8
# 25233
x4
5
1
GB
GB
?
(x2)
?
Front
Front
Assembly Instructions
Step 6
Mount drawer runners
1.
Extend drawer runner
41434 .
2.
Attach the drawer
runners at the fronts of
divider panels GB .
Place at head screws
25233 and 26020 into
the correct holes as
displayed at the bottom
of this page, into the
divider panels GB .
Fittings you will need for this step:
Flat head screw
#26020 x8
Flat head screw
#25233 x4
Drawer runner
#41434 x4
Please note the hole
rows in which to place
the drawer runners.
OBS: Tighten the screws
but do not overtighten.
5
1
1
Front
GB
GB
Front
12
Front
9
x2
B 76428
C 76427
Top
Bottom
Assembly Instructions
Step 7
Fittings you will need for this step:
Gathering proles
Insert wedges 33204
into the slots in the angle
ends of side prole B +
C , and front prole A .
Wedges
#33204 x4
Top
Please use a hammer for
this assembly step.
Step 8
Attach panels
Place bottom panel ID
on top as shown, and
insert at head screws
26033 .
Bottom
x2
A 76460_01
C 76427
Fittings you will need for this step:
Flat head screw
#26033 x22
B 76428
10
ID
x2
C
B
UB
UC
(x4)
Assembly Instructions
Step 9
Fittings you will need for this step:
Attach bracket
Insert bracket 11229
into xed shelf UC and
UB .
Bracket
#11229 x20
UC
(x4)
UB
Step 10
Attach side panels
Insert connector bolt
25610 with allen key
97642 into bottom panel
ID to the bottom ends
of the side panels.
Please use books or the
like to support the side
panels when assembling
this step.
Fittings you will need for this step:
Connector bolt
#25610 x12
Allen key
#97642 x1
FA
GB
FA
GB
ID
11
Assembly Instructions
ID
GB
FA
GB
FA
ID
Step 11
Insert connector bolt
25610 with allen key
97642 into top panel ID
to the top ends of the side
panels.
Fittings you will need for this step:
Connector bolt
#25610 x12
Allen key
#97642 x1
Step 12
Attach shelves
Place xed shelf UC
as pictured. Slide down
over the screws and then
tighten.
ID
GB
GB
FA
Fittings you will need for this step:
Screw
#25440 x2
Wrench
#91410 x1
FA
ID
Afterwards, attach
wrench 97642 with
screws 25610 onto the
centered backside of the
front prole A .
Please note the
orientation of the
assembly as pictured.
12
UC
FA
UC
ID
GB
UC
FA
GB
UC
UB
ID
Assembly Instructions
Step 13
Fittings you will need for this step:
Fixate back panels
Use nails 23006 to x
the back panels.
Important:
The unit MUST be
square when the
back panels are
attached.
Big nail
#23010 x6
UC
UC
FA
09791
UC
Fixate the back panels
with the big nails 23010
and nail 23006 .
UC
FA
GB
GB
UC
ID
UC
FA
09791
UC
FA
UC
ID
13
Assembly Instructions
Step 14
Fittings you will need for this step:
Fixate the remaining
back panels
Slide the back panels as
shown, so that they meet
back panel 09791 .
Fix the 2 back panels
09790 with nails 23006 .
Nail
#23006 x4
25 pcs
Big nail
#23010 x30
09790
09791
09790
FA
ID
09790
14
09791
09790
FA
ID
09790
09791
09790
FA
ID
Assembly Instructions
Step 15
Attach oor gliders
Place the oor gliders
63008 in the holes of the
bottom panel ID .
Use a wooden block
between your hammer
and the oor gliders.
Fittings you will need for this step:
Floor glider
#63008 x8
09790
09790
09791
Step 16
Mount on your wall
Fix the unit to your wall
with strap 94009 .
The screw supplied
with the anti-topple
bracket is to be used
only to x the
anti-topple bracket
to the furniture. In
addition to this, you
will need to choose
a screw or a tting
suitable for securing
the bracket to the
kind of wall you
have.
If you are unsure
about what type of
screw to use, please
contact your local
hardware store for
more information.
Fittings you will need for this step:
Strap
#94009 x2
FA
3 cm
FA
UC
ID
UC
09790
GB
ID
UB
ID
09791
GB
94009
UC
09790
FA
UC
15
ID
UC
09791
UC
FA
GB
GB
FA
UC
UB
UC
ID
ID
UC
09791
UC
FA
GB
GB
FA
UC
UB
UC
ID
Assembly Instructions
Step 17
Fittings you will need for this step:
Hanger
#72509 x1
UC
Insert hangers 72501
and 72509 .
ID
Hanger
#72501 x2
UC
Step 18
Attach the shelf
supports
Press the shelf support
11042 into the holes of
side panels FA .
Press down the loose
shelf panel T x4.
09791
FA
GB
UC
UB
ID
Fittings you will need for this step:
Shelf support
#11042 x16
ID
GB
FA
UC
UC
16
FA
UC
T
T
UC
GB
09791
UB
ID
GB
T
FA
T
UC
ID
09791
GB
T
T
T
GB
FA
T
UC
ID
UB
UC
FA
UC
Assembly Instructions
Step 19
Fittings you will need for this step:
Insert stop 96203 on
the front edges of both
divider panels GB .
Stop
#96203 x4
Please ensure that the
stops are placed on the
edges as illustrated,
sitting as close to the
side panels FA .
ID
UC
GB
FA
T
GB
T
09791
FA
T
T
UB
UC
ID
UC
Step 20
Attach hinges
Press hinge 52291 into
the large holes on the
doors 18732 , 18743
and 18744 . Screw the
pre-attached screws into
the holes on the doors.
Fittings you will need for this step:
Hinge
#52291 x14
18744
18743
18732
(x2)
17
ID
UC
09791
FA
UC
FA
GB
GB
ID
UB
UC
UC
18743
18732
18732
18744
T
T
T
T
Assembly Instructions
Step 21
Attach doors
Slide the pivoting part
of the two hinges over
the hinge plates. Tighten
the screw on the hinge
plate until the doors are
supported by the hinges.
ID
UC
Please refer to the last
page of this assembly
instruction, showing
how to adjust the doors
according to your needs.
Step 22
Attach door handles
and stops
Pass machine screw
26232 through the
doors, into the handles
81040 and then tighten.
UC
09791
18732
GB
T
18743
FA
T
UC
Fittings you will need for this step:
Handle
#81040 x4
Machine screw
#26232 x4
UB
ID
GB
Stop
#96203 x4
FA
T
18732
T
UC
18744
Insert stop 96203 on
shelve UB , and the
wrench as illustrated.
18
FA
UC
GB
T
18743
T
UC
ID
18732
UB
09791
ID
18732
UC
UC
T
T
18744
FA
x2
00734
00733
Assembly Instructions
Step 23
Assemble drawers
Put in dowels 20203
into the end holes of
00733 and 00734 as
illustrated.
Fittings you will need for this step:
Dowel
#20203 x8
00733
00734
x2
Step 24
Assemble drawers
Insert cam 31687 into
00733 and 00733 ,
followed by inserting cam
bolt 31515 into drawer
front EE .
Fittings you will need for this step:
Cam
#31687 x4
Cam bolt
#31315 x4
00734
00733
EE
x2
19
Assembly Instructions
00734
03336
x2
Step 25
Fittings you will need for this step:
Fix drawer panels
together
Align the left 00734 and
right 00733 drawer
sides with the drawer
back 03336 , as
illustrated. Use drawer
fasteners 20228 with a
hammer to x the drawer
sides and the drawer
back together.
Drawer fastener
#20228 x8
00733
00734
03336
x2
Step 26
Attach the drawer
bottom
Slide the drawer bottoms
07165 into the grooves
made of the drawer
sides.
Please note to slide
in the drawer bottom
with the nished side
upwards.
00734
07165
03336
00733
20
x2
00733
00734
EE
07165
03336
x2
Assembly Instructions
Step 27
Attach the drawer front
Attach the drawer front
EE by placing dowels
and cam bolt into the
designated holes.
Please note the
illustration for correct
assembly.
Afterwards, tighten the
cams.
00734
EE
Step 28
Attach the handles
Attach the handles
81040 in front of the
drawer front EE . Use
the machine screws
26232 to tighten the
handles.
07165
00733
Fittings you will need for this step:
Handle
#81040 x4
Machine screw
#26232 x4
03336
x2
00733
00734
EE
07165
03336
x2
21
07165
00734
x2
03336
Assembly Instructions
Step 29
Attach the drawer
bottom supports
Place the drawer bottom
supports 10503 on the
underside of the drawers.
See the detail drawing for
correct assembly.
Use the screw 25440 to
tighten.
Fittings you will need for this step:
Screw
#25440 x6
Drawer bottom support
#10503 x2
Step 30
Pull out the runners
Pull out all of the drawer
runners, before mounting
the drawers.
FA
00734
18744
07165
03336
x2
ID
18743
18732
18732
22
ID
Assembly Instructions
Step 31
Mount the drawers
Slide the drawers onto
the drawer runners,
using the drawers
outside grooves.
Once the drawer runners
reach the drawer front,
screw in the machine
screws 26214 from the
inside of the drawers
to fasten the drawer
runners to the drawers.
See the illustration for
reference.
Fittings you will need for this step:
Machine screw
#26214 x4
After this assembly
step, the assembly is
now complete.
EE
EE
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
23
1.
1.
1.
2.
3.
3.
2.
2.
3.
24
Loading...