Argos 6999524 ASSEMBLY INSTRUCTIONS

Tall Unit Shelf and Drawer

Assembly Instructions

-

Please keep for future reference

699/9524

Dimensions

Width - 84cm

Depth - 51cm

Height - 135cm

Important

-

Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline:

Argos = 0345 6400800

Version 1 Date: 03/05/17

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the

components and tools listed on the following pages.

• Remove all ﬁ ttings from the plastic bags and separate them into their groups.

• Keep children and animals

away from the work area, small parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use bleach or abrasive cleaners.

Handy Hints

• During assembly do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its ﬁ nal position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your ﬂ oor.

• Parts of the assembly will be

easier with 2 people.

• From time to time check that

there are no loose screws on this unit.

• To reduce the likelihood of damaging your product please

ensure that your power drill is set on a low torque setting.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• Regularly check and ensure

that all bolts and ﬁ ttings are tightend properly.

Note: if required the next page can be cut out and used

as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call the

Components - Panels

Customer Helpline:

Please check you have all the panels listed below

Argos = 0345 6400800

Table top

1

Table bottom support

2

Right front leg

3

Right back leg

4

Left front leg

5

Left back leg

6

(77.6 x 50cm)

(141.1 x 6cm)

(134 x 6cm)

(74.6 x 23.8cm)

(141.1 x 6cm)

(134 x 6cm)

Middle panel

12

Left shelf

13

Bottom panel

14

Right bottom support

15

Left bottom support

16

Bottom back panel

17

(24 x 20.7cm)

(43.1 x 27.7cm)

(77.6 x 16.5cm)

(45 x 6cm)

(77.7 x 10cm)

Right side panel

7

Left side panel

8

Back panel

9

Top shelf

10

Upper back panel

11

Pilot holes for guidance only

(46.4 x 10cm)

Pilot holes for guidance only

(46.4 x 10cm)

(77.7 x 10cm)

(77.6 x 14.7cm)

(77.7 x 10cm)

Drawer front panel

18

Drawer right side panel

19

Drawer left side panel

20

Drawer back panel

21

Drawer bottom support

22

Drawer bottom panel

23

(77 x 10cm)

(34 x 7cm)

(71.4 x 7cm)

(32.7 x 6cm)

(72.3 x 33.6cm)

2

Components - Fittings

Please check you have all the ﬁ ttings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more ﬁ ttings may be supplied than are required.

A

90mm Screw x 2

D

30mm Screw x 10

G

12mm Locking nut x 17

J

Screw cover x 10

M

14mm Screw x 2

P

Door pad x 2

B

65mm Screw x 10

E

39mm Locking pin x 20

H

10mm Locking nut x 3

K

Runner x 2

N O

Wall plug

x 2

C

50mm Screw x 8

F

30mm Dowel x 23

I

12mm Screw x 2

L

(This Screw is included in the bag of runner)

12mm Screw x 16

Wall strap x 2

(This screw is included in the wall strap bag)

x 2

Tools required

Phillips screwdriver (medium & large)

Flatblade screwdriver (medium)

Drill

7mm Suitable drill bit (for use with wall plug)

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

The screws length is measured from the head to the point (30mm screw shown).

3

105

Small hammer

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape measure

Eye protection (when using a hammer or glue)

110 115 120 125 130 135 140 145 150 155 160 165 170

Assembly Instructions

Step 1

Attaching upper shelves

a:

Insert Dowels into

Upper back panel 11 .

Screw Locking pin into the Top shelf 10 .

Note:

Insert Locking pins

F

11

E

10

as far as shown.

Do not over tighten.

Use Screws (2 pcs) to

C

fix the Top shelf 10 on to the Upper back panel .

b:

Insert Dowel into

Middle panel 12 .

12

10

11

F

Carefully locate the Top

unit onto the Middle panel

12 .

12

Insert Locking nut G into

the Middle panel 12 .

G

12

a:

Finished front surface

F

b:

F

12

F

11

10

E

C

G

E

C

Use a screwdriver to turn Locking nuts G clockwise.

c:

Insert Dowel ○ into

Left shelf 13 .

Fix the Left shelf onto

G

F

13

the unit.

c:

10

G

F

13

F

12

Finished front edge

13

4

Assembly Instructions

Step 1 - continued

d:

Screw 6 Locking pins

E

into the Table top 1 .

Note:

Insert Locking pins

1

as far as shown.

Do not over tighten.

Use Screws C to fix the Table top 1 on to the

C

1

unit.

Step 2

Attaching runners

a:

Position Runners in

front edge of the Right side

panel 7 .

7

K

d:

a:

E

1

E

12

7

K

Middle hole

E

1

C

L

Slide top of the Runners

K

back.

Use screws to fix the

Runners on Right side

panel .

Slide top of Runners

L

K

7

K

forward and fix as shown using Screws .

Insert Dowel into the

Right side panel 7 .

Screw Locking pin into

the Right side panel 7 .

Note:

Insert Locking pins

L

F

7

E

7

as far as shown.

Do not over tighten.

L

1.7cm

7

K

Middle hole

B

L

F

L

F

L

7

L

K

A

E

K

E

7

Continued on next page.

5

Assembly Instructions

Step 2 - continued

b:

Position Runners in

K

front edge of the Left side panel 8 .

8

Slide top of the Runners

K

back.

Use screws to fix the

Runners on Left side

panel 8 .

Slide top of Runners

L

K

8

K

forward and fix as shown using Screws .

Insert Dowel into the Left side panel 8 .

Screw Locking pin into the Left side panel 8 .

Note:

Insert Locking pins

L

F

8

E

8

as far as shown.

Do not over tighten.

b:

1.7cm

8

L

F

Middle hole

L

E

F

L

Middle hole

K

L

8

K

8

L

E

Step 3

Attaching drawer

a:

Insert Dowel into the

Table bottom support 2 .

Carefully locate the Table bottom support 2 onto Left side panel 8 and

Right side panel 7 .

Insert Locking nut into the Table bottom support 2 .

2

Use a screwdriver to turn Locking nuts clockwise.

Continued on next page.

F

2

8

7

G

a:

K

G

F

8

2

F

7

G

2

G

6

Assembly Instructions

Step 3 - continued

b:

Use Screws (2 pcs) to fix the Back panel 9 onto the Left side panel 8

and Right side panel 7 .

C

9

8

7

b:

C

F

Finished front surface

7

9

Insert Dowel into the Back panel 9 .

c:

Carefully locate the

F

9

Keyboard unit onto the Table top .

Insert 4 Locking nuts into the Left side panel 8

and Right side panel 7 .

1

G

8

7

Use a screwdriver to turn Locking nuts clockwise.

G

Step 4

Attaching bottom unit

a:

Insert Dowel into the

Left bottom support 16 and

Right bottom support 15 .

Screw 2 Locking pins into the Bottom panel 14 .

F

16

15

E

14

c:

a:

F

8

G

1

G

8

F

G

9

7

E

Note:

Insert Locking pins

as far as shown.

Do not over tighten.

b:

Carefully locate the Bottom panel 14 onto the

14

Left bottom support 16 and

Right bottom support 15 .

Insert Locking nut into

16

15

G

the Left bottom support 16

and Right bottom support

15

15 .

Use a screwdriver to turn Locking nuts clockwise.

7

G

16

b:

16

15

E

14

G

14

G

15

Assembly Instructions

Step 4 - continued

c:

Use Screws (2 pcs)

to fix the Bottom panel

C

14

onto the Bottom back panel 17 .

Insert Dowels into the Bottom back panel 17 .

17

F

17

Step 5

Attaching legs

a:

Screw 6 Locking pins

E

into Right/Left back

legs 6 and 4 .

6

4

c:

a:

C

F

E

6

17

14

E

F

E

4

E

Use Screws (2 pcs) to

A

fix the Right/Left front legs 5 & 3 onto the Right/

5 3

Left back legs 6 and 4 .

6 4

A

6

5

3

A

4

Continued on next page.

8

Assembly Instructions

Step 5 - continued

b:

Use Screws B (5 pcs) and Screw D to fix the Left side legs 5 & 6

B

D

5 6

onto the table top and bottom units.

Use Screw covers to cover the Screw heads .

J

B

J

b:

B

11

B

J

B

J

B

10

8

13

5

6

1

16

D

17

c:

Use Screws B (5 pcs)

and Screw D to fix the

Right side legs 3 & 4

B

D

3 4

onto the unit.

Use Screw covers to cover the Screw heads .

J

B

c:

B

1

7

D

17

J

B

15

B

3

4

J

B

Continued on next page.

9

Assembly Instructions

Step 5 - continued

d:

Insert 8 Locking nuts

G

into back panels 11 , 9 and 17 .

9 17

11

Use a screwdriver to turn Locking nuts clockwise

G

d:

G

11

G

1

9

G

Step 6

Drawer assembly

a:

Screw 3 Locking pins

E

into Drawer front panel 18 .

18

Note:

as far as shown.

Do not over tighten.

Tear off the protective backing from the Door Pads .

Carefully stick the Door pads onto the Drawer front panel .

Insert Locking pins

P

18

a:

G

17

G

E

P

E

18

P

G

E

P

Continued on next page.

10

Assembly Instructions

Step 6 - continued

b:

Insert Dowel into the

Drawer left side panel 20

F

20

and Drawer right side panel 19 .

19

Fix Drawer left side panel

20

20 , right side panel 19

19

and Drawer bottom support onto the Drawer front panel .

Insert 3 Locking nuts

22

18

H

into Drawer left side panel 20 , Drawer right side

20

panel 19 and Drawer bottom support 22 .

19

22

Use a screwdriver to turn Locking nuts clockwise.

H

b:

G

19

F

20

H

20

H

22

19

H

18

c:

Carefully slide the Drawer bottom panel 23

23

into the grooves as shown.

Position the Drawer back panel 21 onto the unit using Screw D .

21

D

c:

19

23

18

Unfinished back surface

20

D

21

20

23

22

D

19

11

Assembly Instructions

Step 8

Step 7

Fixing to wall

Warning:

In order to prevent overturning, this product must be used with the wall attachment device provided.

Use Screws(2 pcs) to fix Wall straps(2 pcs)

M

O

onto the unit.

With help, move this product into position.

wall

N

O

M

Top panel

Note:

Wall plugs supplied are

for solid wall only.

O

be used for your wall, seek professional advice if in doubt

O

N

Warning:

This product is heavy.

Lift with care.

Mark fixing hole on wall

and remove this product.

Drill 2 holes and insert Wall pulgs(2 pcs) .

Warning:

N

Before drilling, check wall for hidden pipes and and cables.

Reposition this product and fix wall straps using Screws(2 pcs) .

O

Back panel

12

Assembly Instructions

Step 8

Inserting drawers

a: Pull runners out. Slide

drawers onto runners so they butt up against back of drawer front.

b: Fix through drawer

sides into runners using screws .

D

a:

1

8

7

D

Assembly is complete.

b:

D

18

D

If you need help or have damaged or missing parts, call the

Argos = 0345 6400800

13

A Guide to - Wall Mounting & Fixings

Important note:

If plastic wall plugs are supplied with your product:

- these are only suitable for use in masonry walls.

If you are in any doubt about the correct wall plugs for your wall, seek professional advice.

Failure of the product due to

responsibility of the installer.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualiﬁed tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.

5:

drilled hole.

Types of walls

No.1 “General Purpose” wall plug

Generally aerated blocks should not be used to support heavy loads, use

loads, general purpose wall plugs can be used.

No.2 “Plasterboard” wall plug

You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood.

No.3 “Cavity Fixing” wall plug

For use with plasterboard partitions or hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

For use with walls stuck with

is secure to the retaining wall.

No.6 “Shield Anchor” wall plug

Heavy loads

For use when attaching light loads on to plasterboard partitions.

Care & Maintenance

heavy loads such as shelving, wall cabinets and coat racks.

Safety: Always check the ﬁtting and location to ensure your safety in and around the home.

For use with heavier loads such as TV & HiFi speakers and satelite dishes etc.

Fitting: From time to time check the ﬁtting to ensure the wall plugs or screws do not become loose.

Revision 2 - 7/10/09