Toronto Single
Assembly Instructions - Please k eep for future reference
697/0804
697/0770
697/0835
697/0749
Dimensions
Width - 96cm
length - 190cm
Height - 85cm
Issue 2 - 31/01/2014
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or
missing parts, call our Customer Helpline: 01242 621266
Safety and Care Advice
Important–Please read these instructionsfully before starting assembly
•
Check you have all the
components and tools listed
on pages 2 and 3.
• Remove all ?ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the product, this could
cause damage.
• Assemble the item as close
to its ?nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging
the unit or your ?oor.
the unit or your ?oor.
• Parts of the assembly will
be easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below
• Skin contact: Remove
contamination by washing with
soap and water.This procedure
should also be followed prior to
eating and drinking.
• Eye contact: Rinse immediately
with clean water for 15minutes
and seek medical advice.
• If swallowed: Seek medical
advice immediately.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Care and maintenance
• Only clean using a d amp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screw son
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: This assembly
instruction covers a number of
different sizes of bed.
Although your bed may
appear different to the model
shown the assembly
procedure remains identical.
1
Components-Fittings
If you have any damaged or
missing parts, call our Customer Helpline: 01242 621266
Please check you have all the ?ttings listed below
Note:The quantities below are the correct amount to complete the assembly. In some cases more
?ttings may be supplied than are required.
A
60mm Allen Bolt x 8
D
B
35mm CS Screw x8
E
4mm x 25mm Screw x 2 15mm Round Head screw X 18
G
12mm CAM Lock
H
x 10
M6 Cross dowel x 8
J
M
Silver Handle
x 2
Allen Key
x1
K
Washer
x 12
N
Wooden dowel x 8
Tools required
Cross Headed Screwdriver
C
25mm Allen Screw x 4
F
CAM Peg x 10
I
Castor
x 5
L
15ml Glue Tube
x1
O
Small
hammer
Flat Headed Screwdriver
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Allen Key
(Supplied)
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the fixings
05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
2
Components-Panels
Please check you have all the panels listed below
Bed Panels
Side Rails x 2
1
Toe End Panel x 1
2
Head End Panel x 1 (96 x 49cm)
3
Headboard Struts x 2
4
5
Headboard Rails x 2 (96 x 17cm)
6
Roll of Slats x 1
(190 x 18cm)
(96 x 35cm)
5
5
6
1
1
4
4
3
Underbed drawer Panels
7
Drawer Base x 2 (90 x 40cm)
8
Drawer Side x 2 (39 x 12cm)
Support Rails x 2 (39 x 6cm)
9
Centre Support x 1 (39 x 6cm)
10
11
Drawer Back x 1 (182 x 12cm)
Drawer Front x 1 (188 x 12cm)
12
2
11
7
9
7
12
8
10
8
9
3
Assembly Instructions
Step 1
Fitting the side rails
to the head end panel
Position the side rails
as shown and fit 2 x M6
Cross dowels in to
H
the side rails. Note that
the slot must be aligned
as shown in the diagram.
Next fit the M6 x 60 bolts
through the head end
and in to the ends of the
side rails. Use the 4mm
Allen key to tighten the
bolts in to the cross
dowels.
H
x 4
x 4 x 4
A
1
x 4
Note the correct
alignment of the
3
Cross Dowel slots
H
H
H
H
1
1
A
A
3
H
H
A
A
Step 2
Fitting the side rails
to the toe end panel
Position the side rails
as shown and fit 2 x M6
Cross dowels in to
H
the side rails. Note that
the slot must be aligned
as shown in the diagram.
Next fit the M6 x 60 bolts
through the toe end
and in to the ends of the
side rails. Use the 4mm
Allen key to tighten the
bolts in to the cross
dowels.
A
H
1
2
A
Note the correct
alignment of the
Cross Dowel slots
H
H
H
A
A
HHH
H
2
HHH
A
A
x 4 x 4
4
Assembly Instructions
Step 3
Fitting the headboard
struts to the head
board rails
Position the headboard
rails and headboard
struts as shown.
Fix the struts to the rails
using 8 x 15mm round
head screws
Note that the pilot holes
on the headboard rails
are offset - see diagram
below.
4
5
E
E
x 8
Note offset
pilot holes
in the
headboard
rails
E
E
Pilot Holes
a
b
b
a
E
E
Pilot Holes
4
5
5
4
Step 4
Fitting the headboard
assembly to the head
end panel
Fix the assembled
headboard on to the
back of the head end
panel using 4 x 25mm
Allen screws and
12 x washers
Note that there are 6
holes in the head end
panel. Please use the
top 4 holes to fit the
struts as shown in the
detail view.
C
3
C
K
K
Use top holes
Detail View
C
K
C
K
C
K
x 4
x 12
5
Assembly Instructions
Step 5
Fitting the roll of slats
6
to the side rails.
Open the roll of slats
and lay them on the
side rails as shown.
Pull the end slats out
so that they touch the
head end panel and
the toe end panel.
Secure each corner
using 4 x 35mm screw
B
B
B
B
B
6
B
The side rails may be
slightly bowed out. If so
push them in on both
sides before fitting the
last 4 x 35mm screw
B
x 8
Step 6
Fitting the wooden
dowels to the
support rails and the
CAM Lock to the
Centre Support Rail
as shown.
N
9
G
10
B
B
Push
G
Push
L
Put a small amount of
glue in to the holes and
gently tap the wooden
dowels in to the support
rails as shown.
Wipe off any excess
glue with a damp cloth
N
x 8
G
x 2
N
L
Glue the dowels
in place
G
10
9
9
N
N
L
L
N
N
L
6
Assembly Instructions
Step 7
Fitting the castors
to the support rails
10
and
Position the support
9
rails and the
castors as shown.
I
Using the round head
screws fix the
castors to the
support rails as
E
I
9
shown.
I
x 5
E
x 10
I
9
E
I
9
I
E
I
E
I
E
10
9
E
I
Step 8
Fitting the cam pegs
to the drawer back
12
12
11
F
11
12
F
x 10
and front.
Position the drawer
front and back
as shown. Attach the
cam pegs to the
drawer back and
drawer front
11
E
F
F
F
F
F
11
F
F
F
12
The cam fixing pegs should be
screwed down to this shoulder
F
7
Assembly Instructions
Step 9
Fitting the support
9
rails and drawer
sides to the drawer
front
Position the drawer
sides and the
support rails and
Centre Support Rail
as shown. Put a small
amount of glue into
the holes and gently
tap the support rails
into the drawer front
as shown.
Wipe off any excess
gluewithdampcloth.
Attach the cam lock
fix the drawer sides
to the drawer front
as shown.
8
12
8
9
10
12
G
8
12
8
9
N
L
L
9
L
9
Glue the dowels
10
L
12
G
in place
8
G
Note use plenty of glue
G
Do not assemble the
drawers if the dowels
are not glued.
G
x 4
Step 10
Fitting the drawer
bases and the
drawer back
Position the drawers
as shown. Put a small
amount of glue into the
holes and gently tap the
drawer back to the
support rails as shown.
Wipe off any excess of
glue with damp cloth.
Slide the drawer bases
in to the drawer sides
and drawer front
Attach the cam lock
fix the drawer back
to the drawer sides.
7
11
11
8
12
G
11
8
G
N
L
Glue the dowels
in place
L
G
8
L
G
L
11
7
7
12
L
8
x 4
1
2
3
4
CAM FIXING STEPS
8
Assembly Instructions
Step 11
Fitting the handles
to the drawer front
Position the drawer as
shown. Use 2 x screw
to fix the silver
D
handle to the drawer
front as shown.
J
D
x 2 x 2
J
12
J
D
12
D
J
J
Step 12
Finally push the drawer
unit under the bed frame.
The bed is now complete.
If you need help or have damaged or
missing parts, call our Customer Helpline: 01242 621928
9
Loading...