Argos 6704 ASSEMBLY INSTRUCTIONS

Corner TV Unit with 2 Doors

Assembly Instructions

-

Please keep for future reference

389/6039

Dimensions

Width - 92cm

Depth - 39.5cm

Height - 48cm

Important

-

Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline:

Argos = 0345 6400800

Version 1 Date: 27/04/15

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the

components and tools listed on the following pages.

• Remove all ﬁ ttings from the plastic bags and separate them into their groups.

• Keep children and animals

away from the work area, small parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use bleach or abrasive cleaners.

Handy Hints

• During assembly do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its ﬁ nal position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your ﬂ oor.

• Parts of the assembly will be

easier with 2 people.

• From time to time check that

there are no loose screws on this unit.

• To reduce the likelihood of damaging your product please

ensure that your power drill is set on a low torque setting.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• Regularly check and ensure

that all bolts and ﬁ ttings are tightend properly.

Note: if required the next page can be cut out and used

as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call the

Components - Panels

Customer Helpline:

Please check you have all the panels listed below

Argos = 0345 6400800

Top panel (92 x 39cm)

1

Bottom panel

2

Middle Left panel

3

(37.1 x 37.1cm)

Pilot holes for

guidance only

(92 x 39cm)

Middle right panel

4

(37.1 x 37.1cm)

Finished front edge

Middle shelf panel

9

Shelf panel x 2

10

Front panel

11

Left side support

12

Right side support

13

(48 x 37cm)

(18.8 x 14.5cm)

(82 x 6cm)

(16.5 x 6cm)

Pilot holes for

guidance only

Left panel

5

(37.1 x 19.2cm)

Pilot holes for guidance only

Left door panel

7

(35.2 x 20cm)

Pilot holes for guidance only

Right panel

6

(37.1 x 19.2cm)

Pilot holes for guidance only

Right door panel

8

(35.2 x 20cm)

Door support x 2

14

Large back panel

15

Small back panel x 2

16

(37.1 x 19.5cm)

(18.8 x 2.5cm)

(50.3 x 40cm)

2

Components - Fittings

Please check you have all the ﬁ ttings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more ﬁ ttings may be supplied than are required.

A B C

30mm Dowel x 6

D

43mm Locking pin x 8

G

E F

14mm Screw x 8

H

Door hinge x 415mm Locking nut x 8

J K L

M N

Door pad x 4Support cover x 8

40mm Screw x 450mm Screw x 14

(This screw is included in the door hinge bag)

15mm Screw x 16

I

Foot x 1

Shelf support x 8Nail x 10Plastic support x 3

Tools required

Phillips screwdriver (medium & large)

Flatblade screwdriver (medium)

Drill

7mm Suitable drill bit (for use with wall plug)

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

The screws length is measured from the head to the point (30mm screw shown).

3

105

Small hammer

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape measure

Eye protection (when using a hammer or glue)

110 115 120 125 130 135 140 145 150 155 160 165 170

Assembly Instructions

Step 1

Attaching the middle shelf panel

a:

Insert Dowels into

the Middle left panel

A

3

and Middle right panel

.

4

Use Screws to fix the

Middle left panel and Middle right panel onto

B

3

4

the Middle shelf panel

9

.

Step 2

Attaching top panel

a:

Screw Locking pins

into the Top panel .

D

1

a:

Unfinished back edge

A

3

B

D

B

A

B

4

9

D

Insert Locking pins

Note:

as far as shown.

Do not over tighten.

b:

Carefully locate the

Top panel onto the

1

unit.

Insert 4 Locking nuts

G

into the unit.

Use a screwdriver to turn

Locking nuts clockwise

G

to lock.

b:

D

G

1

D

4

3

G

1

4

Assembly Instructions

Step 3

Attaching left and right panels

a:

Use Screws to fix

the Door hinges ‘back

F

H

plates’ onto the Right panel

6 5

and Left panel .

b:

Carefully locate the

Right

panel and Left

panel onto the unit.

Insert 4 Locking nuts

6

5

G

into the unit.

Use a screwdriver to turn

Locking nuts clockwise

G

to lock.

a:

b:

F

H

G

H

6

F

H

F

5

H

5

G

F

H

c:

Use Screws to fix the Door supports onto the Top panel .

C

14

1

c:

14

6

Finished front surface

C

14

1

G

C

14

C

1

5

Assembly Instructions

Step 4

Attaching small back panels

Slide small back panels

16

into the unit.

Step 5

Attaching bottom panel

a:

Finished front surface

16

E

a:

Use Screws to fix

Plastic supports onto

the Front panel .

b:

Insert Dowels into

Right side support and Left side support .

c:

Carefully locate the

Right side support and Left side support onto the Front panel .

E

J

11

A

13

12

13

12

11

b:

c:

E

J

11

13

J

12

A

Unfinished back surface

E

J

A

12

Continued on next page.

Finished

front surface

11

13

6

Assembly Instructions

Step - continued 5

d:

Use Screws to fix

the Bottom panel onto the Right side support

and Left side support .

B

2

13

12

d:

B

12

e:

Use Screws to fix

Front panel onto the

Bottom panel .

Use Screws to fix Foot

I

onto the Bottom panel

2

.

E

11

2

E

e:

B

13

E

I

2

E

2

E

I

E

11

E

f:

Use Screws to fix

the Bottom panel

B

2

onto the unit.

f:

B

3

6

2

4

B

5

7

Assembly Instructions

Step 6

K

Fixing large back panel

Attach large back panel

15

using nails .

Important:

The unit MUST be ‘square’ when back is attached.

K

Unfinished back

surface

15

Step 7

Attaching shelf panels

With help, carefully stand the unit upright.

Warning:

The unit is heavy.

Lift with care.

a: Slide Support covers

M

onto Shelf supports . Insert Shelf supports (Support covers are included) into the unit. Ensure they are well fitted before inserting the Shelves.

Set the shelf

Note:

M

supports to the desired height.

L

a:

b:

M L

+

M L

10

+

M L

10

b:

Slide Shelf panels

into the unit.

10

8

Assembly Instructions

Step 8

Attaching hinges to doors

F

N

Fix 4 Door hinges to Left door panel and Right door panel using

Screws .

F

H

7

8

Tear off the protective backing from the Door Pads .

N

Carefully stick the Door

N

pads onto the Left door panel and Right door

panel .

7

8

Step 9

Hanging doors

a:

With help, slot Door hinges onto ‘hinge plates’.

H

F

N

H

F

7

NN

H

F

H

F

N

H

8

b:

Tighten screw shown

to lock hinges in position.

Repeat

a

and b for

opposite door.

Hinge adjustment

See ‘

’ in step 10 if the doors need adjusting.

a:

8

7

H

b:

9

Assembly Instructions

Step 10

Hinge adjustment

a:

To move doors up or down: loosen screws shown and move doors to suit.

Once doors are aligned,

re-tighten Screws .

b:

To move doors in or out: loosen screw shown and move doors to suit.

Re-tighten screws.

F

a:

Door

b:

F

c:

To move doors left or right: loosen screw shown and move doors to suit.

Re-tighten screws.

Door

c:

Door

10

Assembly Instructions

Step 11

Finishing the unit

Note:

It would be useful to ask someone to help you at this stage.

With help, place the unit in the intended position.

Assembly is complete.

If you need help or have damaged or missing parts, call the Customer Helpline: Argos = 0345 6400800

11