Argos 656-5721, Valencia - 500mm Wall Cabinet, 633-2882, 633-2710, 656-5295 ASSEMBLY INSTRUCTIONS
...
MADE IN
BRITAIN
Cabinet
Black Door Pack
Cream Door Pack
Grey Door Pack
Plum Door Pack
White Door Pack
Dimensions
Width - 50cm
Depth - 34cm
Height - 72cm
Valencia - 500mm Wall Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/08/11
Important - Please read these instructions fully before starting assembly
hygena
656/5721
633/2882
633/2710
656/5295
656/4540
633/2806
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 10kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
2
4
End Panel (DPF141A)
(320 x 716 mm) x 2
Loose Shelf (DPF092A)
(468 x 236mm)
Top/Base Panel (DPF091A)
(469 x 319 mm) x 2
5
Back Panel (DPF093A)
(479 x 694 mm)
Valencia Door (DPF147B)
(497 x 716mm)
The front surface
of this door is
protected with a
peel-off film
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 8
C
D
Large locking
nut (F900) x 8
F
G H
K
I
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
13mm Screw (F63) x 4
E
19mm Connecting bolt (F461) x 2
M
25mm Screw (F50) x 4
Connecting Sleeve (F432) x 2
Shelf support (F110) x 4
Hinge Cover (F119) x 2
h
ygen
a
J
Wall bracket (F198) x 2
Hanging bracket
(F849) x 2
L
Hinge Arm (F118) x 2
Hinge Plate
(F117) x 2
NNa
b
25mm Screw (F132) x 2
Handle (F214) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Choose which way
you would like the
door to open
You can fit the door to
the left side or right side.
If you would like
your door to
open this way,
fit the hinge
plates to the left
end panel
If you would like
your door to
open this way,
fit the hinge
plates to the
right end panel
Step 2
K
Prepare the left end
panel
Refer to step 1 and, if
required, fit 2 hinge
plates onto the left
end panel , orientated
as shown.
Screw 4 metal dowels
into the holes shown on
the left end panel .
Note: Tighten metal
dowels up fully against
the panels.
Fit a hanging bracket
to the left side using
2 screws , making
sure that the hook is
towards the back edge.
1
B
1
B
K
K
B
B
B
B
This will be the
left end panel
1
J
G
G
J
1
G
1
K
Loading...