Argos 457/2156, 651/5070 User guide

HM Wide Media Unit

457/2156 651/5070

Care & Instruction Manual

Please read and retain these instructions for future reference

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the

components and tools listed on the following pages.

• Remove all ﬁ ttings from the plastic bags and separate them into their groups.

• Keep children and animals

away from the work area, small parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before starting.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use bleach or abrasive cleaners.

Handy Hints

• During assembly do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its ﬁ nal position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your ﬂ oor.

• Parts of the assembly will be

easier with 2 people.

• From time to time check that there are no loose screws on this unit.

• To reduce the likelihood of damaging your product please

ensure that your power drill is set on a low torque setting.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• Regularly check and ensure that all bolts and ﬁ ttings are tightend properly.

Note: if required the next page can be cut out and used

as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call the

Components - Panels

Customer Helpline:

Please check you have all the panels listed below

Top panel (60.6 x 13.1cm)

1

Argos = 0345 6400800

Bottom panel

2

15.5 20.6

Right side panel

3

15.5 20.6

Left side panel

4

Middle Shelf

5

(111 x 13cm)

(use screw) (58 x 12.9cm)

Finished front edge

(111 x 13cm)

Finished front edge

(60.6 x 19.6cm)

Shelf x 4

6

Small support x 3

7

Large support x 6

8

(use dowel) (58 x 12.9cm)

(14.9 x 12.8cm)

( (20 x 12.8cm)

Back panel (60 x 113cm)

9

2

Components - Fittings

Please check you have all the ﬁ ttings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more ﬁ ttings may be supplied than are required.

A B C

40mm Screw x 12

D

Screw cover x 8

G

Wall strap x 2

Tools required

(This screw is included in the wall strap bag)

x 2

Phillips screwdriver (medium & large)

E F

14mm Screw x 2

Nail x 2230mm Dowel x 56

Wall plug x 2

Small hammer

Flatblade screwdriver (medium)

Drill

7mm Suitable drill bit (for use with wall plug)

Ruler - Use this ruler to help correctly identify the screws

105

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

The screws length is measured from the head to the point (30mm screw shown).

110 115 120 125 130 135 140 145 150 155 160 165 170

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Ruler/tape measure

Eye protection (when using a hammer or glue)

3

Assembly Instructions

Step

Insert dowels

a:

Right side panel and Left side panel .

b:

Small support , Large support and Shelf .

6

1

Insert Dowels into

8

B

3

4

B

7

a:

B

3

4

B

b:

B

7

B

8

B

6

X 3

X 6

B

X 4

4

Assembly Instructions

Step 2 - continued

Attaching panels

a:

Position

7 8

, Large supports onto Middle shelf .

Small support

5

a:

Finished front edge

7

5

8

b:

Position

onto unit.

Shelves

6

b:

Finished front edge

6

7

8

6

Continued on next page.

5

Assembly Instructions

Step 2 - continued

c:

Position

supports onto unit.

Small

7

8

Finished front edge

8

6

7

d: Position Shelves

onto unit.

6

d:

Finished front edge

6

8

7

6

Continued on next page.

6

Assembly Instructions

Step 2 -

e:

Use Screws to fix

Right side panel and Left side panel onto

continued

A

3

4

unit.

Use Screw covers to

D

cover the screw heads.

e:

Finished front edge

6

A

4

15.5

A

3

6

5

6

D

A

20.6

f: Position Small

support onto unit.

7

D

A

D

f:

Finished front edge

7

3

Continued on next page.

7

4

Assembly Instructions

Step 3

a:

Attaching Top and Bottom panel

a:

Use Screws to fix

Top panel onto unit.

A

1

Use Screw covers to

D

cover the screw heads.

D

A

1

7

4

Finished front edge

3

b:

Position

supports onto unit.

Large

8

b:

Finished front edge

3

4

6

8

Continued on next page.

8

Assembly Instructions

Step 3 -

continued

tructions

d:

a:

Use Screws to fix

Bottom panel onto unit.

A

2

Finished front edge

3

Step 4

Fixing back panel

Attach back panel using nails .

C

Important:

The unit MUST be ‘square’ when back is attached.

9

a:

4

back surface

8

2

A

9

C

3

1

9

Assembly Instructions

Step 5

Fixing to wall

Warning:

In order to prevent overturning, this product must be used with the wall attachment device provided.

wall

E

F

G

Note:

Wall plugs supplied are

for solid wall only.

G

be used for your wall, seek professional advice if in doubt

G

F

Use Screws(2 pcs) to fix Wall straps(2 pcs)

E

G

onto the unit.

With help, move this product into position.

Warning:

This product is heavy.

Lift with care.

Mark fixing hole on wall and remove this product.

Drill 2 holes and insert Wall pulgs(2 pcs) .

Warning:

F

Before drilling, check wall for hidden pipes and and cables.

Top panel

Back panel

Reposition this product and fix wall straps using Screws(2 pcs) .

Assembly is complete.

G

If you need help or have damaged or missing parts, call the Customer Helpline: Argos = 0345 6400800

Produced in Indonesia for Argos Limited, 489-499 Avebury Boulevard, Milton Keynes, MK9 2NW www.argos.co.uk

10

A Guide to - Wall Mounting & Fixings

Important note:

If plastic wall plugs are supplied with your product:

- these are only suitable for use in masonry walls.

If you are in any doubt about the correct wall plugs for your wall, seek professional advice.

Failure of the product due to

responsibility of the installer.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualiﬁed tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.

5:

drilled hole.

Types of walls

No.1 “General Purpose” wall plug

Generally aerated blocks should not be used to support heavy loads, use

loads, general purpose wall plugs can be used.

No.2 “Plasterboard” wall plug

You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood.

No.3 “Cavity Fixing” wall plug

For use with plasterboard partitions or hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

For use with walls stuck with

is secure to the retaining wall.

No.6 “Shield Anchor” wall plug

Heavy loads

For use when attaching light loads on to plasterboard partitions.

Care & Maintenance

heavy loads such as shelving, wall cabinets and coat racks.

Safety: Always check the ﬁtting and location to ensure your safety in and around the home.

For use with heavier loads such as TV & HiFi speakers and satelite dishes etc.

Fitting: From time to time check the ﬁtting to ensure the wall plugs or screws do not become loose.

Revision 2 - 7/10/09