Page 1
Width - 40cm
Depth - 49cm
Height - 89cm
WYTON DINING CHAIR
Assembly Instructions - Please keep for future reference
620/6585
619/4240
Dimensions
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 23/09/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 4.2 kgs.
• Maximum safe weight of user:
11 0kgs.
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
Note: The quantities below are the correct amount to complete the assembly of 1 chair.
Side Rail x 2
2
(2 x 6 x 33cm)
1
(8 x 40 x 89cm)
Front Leg
3
(4.5 x 37 x 42cm)
Components - Fittings
Seat
4
(3.5x 40 x 40cm)
Stretcher x 2
5Backrest
(1.2 x 2.1 x 36cm)
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly of 1 chair. In some cases more
fittings may be supplied than are required.
A
M6 x 50mm Bolt x 6
D
M6 x 30mm Dowel x 6
B
Spring washer x 6
E
Allen key x 1
C
M4 x 32mm Screw x 7
Tools required
Crosshead screwdriver
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
2
Page 4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels
D
into holes on the side
2
rails as shown.
Step 2
Attaching side rails
Place the front leg on
a flat protected surface.
Position the siderails
as shown and insert the
wood dowels into holes
on the front leg. Then fix
using bolts and spring
washers .
A
B
Important note:
Fasten bolts
using allen key
but do not fully
tighten at this
stage. Use oval
head of allen key
when tigthening
bolts on corner
positions.
3
2
E
D
D
D
2
2
D
D
D
A
B
2
2
A
B
3
D
D
2
3
2
A
B
Step 3
Attaching stretchers
Place the backrest on
a flat protected surface.
Position the stretcher
as shown and insert into
the hole on the backrest.
3
1
5
5
5
5
1
1
Page 5
Assembly Instructions
Step 4
Attaching backrest
Then align and insert the
stretchers into holes
on the front leg .
Position the siderails
as shown and insert the
wood dowel into center
holes on backrest .
5
3
2
1
2
3
5
5
5
3
2
2
1
1
Step 5
Securing backrest
Fix the backrest to
siderail using bolts
2
and spring washers .
Note:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Use oval head of
allen key when
tigthening bolts
on corner
positions.
1
A
B
E
2
A
B
2
A
A
B
2
A
B
B
1
A
B
A
B
1
4
Page 6
Assembly Instructions
Step 6
Aligning the legs
Carefully turn the chair
upright and place on a
flat surface.
Make adjustments to
ensure the chair frame is
straight and the legs are
even on the floor then
fully tighten all bolts
assembled in previous
steps using allen key .
E
E
Step 7
Attaching seat
Carefully place the seat
4
face down on a
raised protected surface.
Position the chair on the
centre of the seat and fix
through holes on side
2 3
rails and front leg
using screws .
Tighten screws using a
crosshead screwdriver.
C
C
2
3
2
C
2
C
3
4
C
5
Page 7
Assembly Instructions
Step 8
Securing the stretchers
C
Secure the stretchers
to the backrest and
front leg using scews
C
. .
3
1
5
Tighten screws using
crosshead screwdriver.
1 5
C
C
C
5
1
3
C
5
Carefully turn over the
unit after assembly.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
6
Loading...