Page 1
New Pagnell Deep 3+2 Chest
Assembly Instructions - Please keep for future reference
610/8793
620/5861
619/5139
Dimensions
Width - 76.5cm
Depth - 40.5cm
Height - 82m
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 10/11/16
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Do not use this item if any
components are missing or
damaged.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• From time to time check that
there are no loose screws on
this unit.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age range of
7-12 years.
• Maximum load: 25 kgs.
• Assembly of this product must
be carried out by a competent
adult.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6400800
Pilot holes for guidance only
Left side panel
1
(80.4 x 38cm)
Pilot holes for guidance only
Right side panel
2
Pilot holes for guidance only
Top support
3
(36.2 x 13.6cm)
Finished
front edge
(80.4 x 38cm)
9 Small drawer right
Small drawer left
panel x 4
(34 x 11.5cm)
Large drawer left
11 Large drawer right
panel
(34 x 24cm)
Drill holes
near edge
13 Right drawer front
Left drawer front
(36 x 14.4cm)
panel
Middle drawer front panel
15
x 2 (72.3 x 14.4cm)
10
panel x 4
(34 x 11.5cm)
12
panel
14
(34 x 24cm)
(36 x 14.4cm)
panel
Large drawer support
20
(32.7 x 6cm)
Middle panel
Back bottom panel
Front bottom panel
7
Front panel
Top panel
8
(76.2 x 40cm)
(73 x 11cm)4
(73 x 11cm)5
(73 x 11cm)6
(73 x 4.5cm)
Large drawer front panel
16
(72.3 x 28.7cm)
Small drawer back panel
17
x 2 (32.2 x 11.5cm)
18
Middle drawer back panel
x 2 (69.8 x 11.5cm)
19
Large drawer back panel
(69.8 x 24cm)
21
Small drawer bottom
x 2 (33.1 x 33.6cm)
panel
22
Large drawer bottom
x 3 (70.7 x 33.6cm)
panel
Back panel
23
(77 x 75.8cm)
2
Page 4
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
A
50mm Screw x 2
D
30mm Dowel x 9
G
12mm Locking nut x 21
J
Plastic support x 3
M
Wall strap x 2
(This screw is
included in the
wall strap bag)
x 2
B
30mm Screw x 22
E
Nail x 18
H
12mm Screw x 10
K
Runner x 10
N
Wall plug x 2
C
39mm Locking pin x 33
F
15mm Locking nut x 12
I
14.5mm Screw x 8
(Screws are included in
L
the runners bag)
12mm Screw x 30
O
Glue x 1
Tools required
Phillips screwdriver
(medium & large)
Pencil
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Page 5
Assembly Instructions
Step 1
Attaching runners
Position Runners in
a:
K
front edge of the Right
side panel .
2
Slide top of the Runners
K
back.
Use screws to fix the
Runners on the Right
side panel .
Note:
the runner should be
approximately 1.7cm
from the front edge of the
panel.
L
K
2
The front part of
a:
2
K
K
K
K
K
L
2
L
Middle hole
L
Pilot holes for
runner position
L
1.7cm
L
Finished front edge
Slide top of Runners
b:
K
forward and fix as
shown using Screws .
Insert Dowel into the
D
Right side panel .
Screw Locking pins into
the
Right side panel .
Insert Locking pins
Note:
L
2
C
2
as far as shown.
Do not over tighten.
b:
Middle hole
B
L
L
C
L
C
L
2
L
K
A
C
L
L
L
L
C
L
K
D
K
2
K
Continued on next page.Continued on next page.
K
4
Page 6
Assembly Instructions
Step - continued 1
c:
Position Runners
K
in front edge of the Left
side panel .
1
Slide top of the Runners
K
back.
Use screws to fix the
Runners on the Left
side panel .
Note:
L
K
1
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
c:
1.7cm
Finished front edge
L
Middle hole
L
K
1
1
K
L
L
K
L
K
K
Pilot holes for
runner position
Slide top of Runners
d:
K
forward and fix as
shown using Screws .
Insert Dowel into the
Right side panel .
Screw Locking pins into
the
Right side panel .
Insert Locking pins
Note:
D
L
1
C
1
as far as shown.
Do not over tighten.
d:
1
K
K
C
K
C
1
L
C
K
L
L
L
Middle hole
K
L
L
L
L
L
C
D
L
Continued on next page.
5
Page 7
Assembly Instructions
Step - continued 1
e:
Position Runner in
K
front edge of the Top
support .
3
Slide top of the Runner
K
back.
Use screw to fix the
Runner on the Top
support .
Note:
L
K
3
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
f:
Slide top of Runner
K
forward and fix as
shown using Screws .
L
e:
f:
Middle hole
L
1.7cm
Finished front edge
3
3
K
L
3
L
Middle hole
K
K
Pilot holes for
runner position
L
g:
Turn the Top support
upside down, repeat
3
e
and f with remaining
Runner and Screws .
Insert Dowel into the
Top support .
K L
D
3
g:
Pilot holes for
runner position
Finished
front edge
K
L
L
3
L
K
L
3
K
D
L
3
6
Page 8
Assembly Instructions
Step 2
Attaching plastic
supports
a:
Use Screws to fix
Plastic supports onto
the Front panel .
b:
Use Screws to fix
Front panel onto the
Front bottom panel .
I
J
7
I
7
6
a:
b:
I
I
I
J
I
7
J
I
6
J
7
I
D
I
J
I
Step 3
Attaching bottom panel
and middle panel
4
.
A
3
4
D
D
a:
Insert Dowels into
the Back bottom panel
.
5
b:
lnsert Dowels into the
Middle panel
Use Screws to fix the
Top support onto the
Middle
panel .
D
D
a:
5
D
b:
D
3
Continued on next page.
7
4
A
A
D
Page 9
Assembly Instructions
Step - continued 3
c:
Middle
Left side panel .
Insert Locking nut into
the
Use a screwdriver to turn
Locking nut clockwise
to lock.
Carefully locate the
panel onto the
Middle
4
1
F
panel .
4
F
c:
F
Unfinished
back edge
1
4
F
d:
Carefully locate the
Front bottom panel
onto the Left side panel
1
.
Insert Locking nut into
the Front bottom panel
6
.
Use a screwdriver to turn
Locking nut clockwise
to lock.
F
6
F
d:
F
Unfinished
back edge
1
6
F
8
Page 10
Assembly Instructions
Step -
e:
Carefully locate the
Back bottom panel
9
continued 3
5
onto the Left side panel
1
.
Insert Locking nut into
F
the Back bottom panel
5
.
Use a screwdriver to turn
Locking nut clockwise
F
to lock.
e:
F
Unfinished
back edge
1
5
F
Step 4
Attaching right side
panel
Carefully locate the
Right side panel onto
2
the unit.
Insert 3 Locking nuts
F
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
F
to lock.
Unfinished
back edge
4
5
F
2
F
F
6
Page 11
Assembly Instructions
Step 5
Attaching top panel
a:
Screw Locking pins
C
into the Top panel .
Note:
Insert locking pins
8
as far as shown.
Do not over tighten.
b:
Then carefully locate
the Top panel onto the
8
unit.
a:
C
C
C
C
C
C
C
8
b:
F
Insert 6 Locking nuts
F
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
F
to lock.
Unfinished
back edge
8
F
F
F
1
3
F
2
10
Page 12
Assembly Instructions
Step 6
Fixing back panel
Attach Back panel
onto the unit using Nails
E
.
Important:
The unit MUST
be ‘square’ when
back is attached.
23
E
Unfinished back surface
23
Step 7
Large drawer assembly
a:
Screw Locking pins
C
into the Large drawer
front panel .
Note:
as far as shown.
Do not over tighten.
Continued on next page.
16
Insert locking pins
a:
C
C
C
C
C
C
16
11
Page 13
Assembly Instructions
Step - continued 7
b:
left panel , Large
drawer right panel and
Large drawer support
onto the
front panel .
Insert Locking nuts into
Fix the Large drawer
11
12
20
Large drawer
16
G
the holes (they will only
insert one way).
Use a screwdriver to turn
Locking nuts clockwise
G
to lock.
b:
12
G
11
20
G
G
c:
Place a small amount
of Glue into the grooves.
O
Carefully slide the Large
drawer bottom panel
22
into the grooves.
c:
16
G
G
G
Unfinished
O
back surface
22
O
12
Continued on next page.
16
12
Page 14
Assembly Instructions
Step - continued 7
d:
of Glue onto the Large
drawer bottom panel .
Position the Large drawer
back panel onto the
unit using Screws .
Place a small amount
O
22
19
B
Step 8
Middle drawer assembly
d:
a:
B
B
19
O
B
B
12
22
C
C
C
B
a:
Screw Locking pins
C
into the Middle drawer
front panel .
Note:
as far as shown.
Do not over tighten.
b:
Fix the Small drawer
left panel and Small
drawer right panel onto
the
Middle drawer front
panel .
Insert Locking nuts into
the holes (they will only
insert one way).
Use a screwdriver to turn
Locking nuts clockwise
to lock.
15
Insert locking pins
9
10
15
G
G
b:
C
C
15
X 2
G
9
G
G
Continued on next page.
13
10
15
X 2
G
G
Page 15
Assembly Instructions
Step - continued 8
c:
Place a small amount
of Glue into the grooves.
Carefully slide the Large
drawer bottom panel
into the grooves.
O
22
c:
Unfinished
back surface
O
22
15
d:
Place a small amount
of Glue onto the Large
drawer bottom panel .
Position the Middle drawer
back panel onto the
unit using Screws .
O
22
18
B
d:
10
O
X 2
B
B
18
B
B
10
O
22
X 2
Step 9
Small drawer assembly
a:
Screw Locking pins
into the Left drawer front
panel and Right
drawer front panel .
Note:
as far as shown.
Do not over tighten.
Continued on next page.
13
Insert locking pins
C
14
a:
C
C
C
C
C
C
13
Drill holes
near edge
C
14
C
C
14
Page 16
Assembly Instructions
Step - continued 9
b:
Fix the Small drawer
left panels and Small
drawer right panels
9
10
onto the Left drawer front
panel and Right
drawer front panel .
Insert Locking nuts into
13
14
G
the holes (they will only
insert one way).
Use a screwdriver to turn
Locking nuts clockwise
G
to lock.
b:
G
G
10
9
G
G
10
9
G
G
Drill holes
near edge
13
G
G
G
14
Drill holes
near edge
c:
Carefully slide the Small
drawer bottom panels
21
into the grooves.
d:
Position the Small
drawer back panels
17
onto the units using
Screws .
B
c:
d:
10
17
13
Drill holes
near edge
B
B
2121
10
14
Drill holes
near edge
B
B
17
15
B
B
10
21
13
Drill holes
near edge
B
B
10
21
14
Drill holes
near edge
Page 17
Assembly Instructions
Step 8
Step 10
Fixing to wall
Warning:
In order to prevent
overturning, this
product must be
used with the wall
attachment device
provided.
Use Screws(2 pcs) to
fix Wall straps(2 pcs)
I
M
onto the unit.
With help, move this
product into position.
wall
N
M
I
Top panel
Note:
Wall plugs supplied are
for solid wall only.
M
be used for your wall, seek
professional advice if in doubt
M
M
N
Warning:
This product is
heavy.
Lift with care.
Mark fixing hole on wall
and remove this product.
Drill 2 holes and insert
Wall pulgs(2 pcs) .
Warning:
N
Before drilling,
check wall for
hidden pipes and
and cables.
Reposition this product
and fix wall straps using
Screws(2 pcs) .
M
Back panel
16
Page 18
Assembly Instructions
Step 11
Inserting drawers
a: Pull runners out. Slide
drawers onto runners so
they butt up against back
of drawer front.
b: Fix through drawer
sides into runners using
screws .
H
a:
13
Side panel near the edge.
(Left side small drawer)
8
8
14
Side panel near the edge.
(Right side small drawer)
H
14
b:
15
15
H
H
H
16
H
13
H
H
H
H
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
17
Page 19
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...