Argos 6172516 ASSEMBLY INSTRUCTIONS
Basic Desk
Assembly Instructions
-
Please keep for future reference
617/2516
Dimensions
Width - 70.5cm
Depth - 50cm
Height - 72cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the
Customer Helpline: 08456 400800
Version2 Date:14/04/11
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Note: Only apply the glue once
you are sure of the assembly.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
If you have damaged or missing components,
Components - Panels
call the Customer Helpline: 08456 400800
Please check you have all the panels listed below
Table top
1
Front left leg
2
Front right leg
3
Pilot holes for guidance only
(70.4 x 50cm)
Pilot holes for guidance only
(70.4 x 6cm)
Pilot holes for guidance only
(70.4 x 6cm)
Back panel
7
Pilot holes for guidance only
Back support
8
Pilot holes for guidance only
Front support
9
Pilot holes for guidance only
Right support
10
Pilot holes for guidance only
(60 x 6cm)
(40 x 6cm)
(57 x 6cm)
(57 x 6cm)
4
Left leg
5
Right leg
Pilot holes for guidance only
Bottom panel
6
Pilot holes for guidance only
(70.4 x 6cm)
Pilot holes for guidance only
(70.4 x 6cm)
(60 x 16.5cm)
Left support
11
Pilot holes for guidance only
Bottom right side panel
12
Pilot holes for guidance only
Bottom left side panel
13
(40 x 6cm)
(40 x 6cm)
(40 x 6cm)
2
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
A
14mm Screw x 24
D
Screw cover x 10
G
Glue x 1
B
Plastic support x 12
E
25mm Screw x 12
C
50mm Screw x 12
F
Wooden dowel x 4
Tools required
Phillips screwdriver
(medium & large)
Bradawl
(or sharp point)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
3
Small
hammer
0 1 2 3 4 5 6
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
105
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step 1
Fixing plastic supports
A
Plastic supports onto the
B
Back and Front supports
10
9
11
8
and ,Right and Left
suports and ,
Bottom right side and left
side panels and .
12 13
A
B
A
A
A
B
11
B
8
A
B
B
13
B
A
B
10
A
A
A
B
B
A
12
A
B
A
A
A
B
B
B
A
B
9
B
Step 2
Attaching support
panels
C
Right and Left supports
and onto the Back
and Front supports
and .
Use Screw covers to
cover the Screw Heads.
1110
8
9
D
back edge
C
back edge
C
10
8
9
11
C
D
D
C
4
Loading...