Argos 6143813 ASSEMBLY INSTRUCTIONS

Aruba - Coffee Table
Assembly Instructions - Please keep for future reference
614/3813 614/3820 116/9634
Dimensions
Width - 107cm
Depth - 76cm
Height - 45cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 08456 400 800
or Homebase Customer Helpline: 0845 077 8888
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the components and tools listed on pages 2 and 3.
Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area, small parts could choke if swallowed.
Make sure you have enough space to layout the parts before starting.
Do not stand or put weight on the product, this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your floor.
This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture.
On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly.
We do not recommend the use of power drill/drivers
inserting screws,
as this could damage the unit. Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
for
Care and maintenance
Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product.
Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Components - Panels
Please check you have all the panels listed below
Top panel (107 x 76cm)
1
Leg x 4 (43 x 6cm)
5
Drawer front
6
(43 x 12.2cm)
Drawer sides x 2
7
(29 x 12.2cm)
Front panel (87.2 x 26cm)
2
Back panel (87.2 x 26cm)
3
Drawer back
8
(40.7 x 12.2cm)
Rail (60.4 x 6.5cm)
9
Drawer runner x 2
10
(60.4 x 6.9cm)
Drawer bottom
11
(41.7 x 27.7cm)
Side panel x 2
4
(56.2 x 26cm)
2
If you have damaged or missing components,
Components - Fittings
call the
or Homebase Customer Helpline: 0845 077 8888
Argos Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel x 34
D
35mm Screw x 13
G H
19mm Bolt x 1
Tools required
B
14mm Screw x 2
E
Metal dowel x 16
Drawer handle x 1
C
30mm Screw x 8
F
Locking nut x 16
I
Round metal stud x 20
Phillips screwdriver (medium & large)
Small hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape measure
Eye protection (when using a hammer or glue)
3
Assembly Instructions
Step 1
a:
Drawer assembly.
b:
a: Attach drawer sides
7
to the drawer front
6
using screws .
C
b: Slide drawer bottom
into slots on drawer sides and position drawer back
8
in place.
c: Carefully lay down the
drawer holding drawer back , press the drawer sides and fix them using screws .
Attach handle to the drawer using bolt , then fix handle plate to the drawer using screws
plate is aligned before fixing.
8
H
B
. Make sure handle
C
G
7
7
6
C
C
8
11
c:
C
G
H
C
B
Step 2
Insert dowels into the indicated parts.
A
A
2
A
3
A
A
4
A
2x
A
10
A
9
2x
A
A
4
Assembly Instructions
Step 3
Fitting Metal dowels.
Screw metal dowels into legs .
5
E
E
5
E
Note:
Insert metal dowels as far as shown.
Do not over tighten.
Step 4
Fixing front panel.
With help, fit front panel
2
to legs .
Make sure panel is positioned as shown.
Insert locking nuts
frontp
into anel where shown
Use a screwdriver to turn locking nuts clockwise
to lock
Do not over tighten.
5
4
F
2
.
F
.
E
F
5
F
2
F
5
F
Step 5
Fixing back panel.
With help, fit back panel
3
to legs .
Make sure panel is positioned as shown.
Insert locking nuts
backp
into anel where shown
Use a screwdriver to turn locking nuts clockwise
to lock
Do not over tighten.
5
5
4
2
.
F
.
F
5
F
F
3
F
5
F
Assembly Instructions
Step 6
Fixing side panels.
With help, fit side panels
4
to legs .
Make sure panel is positioned as shown.
5
4
Insert locking nuts into anel where shown
4
sidep s
.
F
4
Use a screwdriver to turn locking nuts clockwise
to lock
.
F
Do not over tighten.
Step 7
Fixing drawer runners.
F
5
4
F
5
F
F
With help, fit drawer runnes to back panel
3
D
10
then fix it using screw .
Attention:
Make sure drawer
runners are positioned correctly as shown in the diagram.
10
10
D
D
3
Attention!
3
10 10
6
Assembly Instructions
Step 8
Insert rail into the back panel .
Step 9
Fixing front frame.
9
3
Note!
The hole on the rail must be up.
Note!
9
3
9
Two people are required for an easier assembly.
With help, p
lace front frame properly ensuring dowels are all fit into their holes at the same time.
Insert locking nuts into anel where shown
4
sidep s
.
F
4
Use a screwdriver to turn locking nuts clockwise
to lock
.
F
Do not over tighten.
Fix drawer runners to the front frame using screws .
D
10
2
2
F
D
F
10
D
10
4
F
F
7
Assembly Instructions
Step 10
Fixingtoppanel.
Two people are required for an easier assembly.
Caution:
Carefully lay the top panel on a soft and clean surface to avoid damaging the product.
Attach assembled frame to the top panel using screws .
fixing top panel, carefully stand the product upright.
1
1
D
Important:
With help, after
D
D
D
D
1
Step 11
a: Fix round metal studs
I
into the pre drilled holes in legs and top panel .
1
b: Insert drawer into unit.
With the back of the drawer past the front frame, use a hammer to tap dowels in flush to drawer sides, this is a safety catch to stop drawer falling out.
5
A
a:
b:
I
A A
I
NO! NO!
I
YES!
I
I
Assembly is complete.
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 08456 400 800
or Homebase Customer Helpline: 0845 077 8888
8
Loading...