Page 1
Boston Basic Modular 2 Half Door
Assembly Instructions - Please keep for future reference
609/0069
609/2610
610/8937
413/6815
414/1941
Dimensions
Width - 60cm
Depth - 30cm
Height - 60cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 3 Date: 19/03/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Top/Bottom panel x 2
1
(60 x 29.5cm)
Argos = 0345 6400800
Pilot holes for
guidance only
Vertical support x 2
4
(29.4 x 27.65cm)
Side panel x 2
2
(56.9 x 29.4cm)
Shelf
3
(56.9 x 29.4cm)
Back panel x 2
5
(29.5 x 59.6cm)
Pilot holes for
guidance only
Door panel x 2
6
(27.1 x 27.1cm)
2
Page 4
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
A
25mm Screw x 2
D
Door hinge x 4
G
12mm Screw x 6
J
30mm Dowel x 8
B
Handle x 2
E
40mm Screw x 8
H
Door stopper x 2
K
Screw cover x 4
C
Metal plate x 2
F
Nail x 20
I
50mm Dowel x 2
Tools required
Phillips screwdriver
(medium & large)
7mm Suitable drill bit
(for use with wall plug)
Drill
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Page 5
Assembly Instructions
Step 1
Attaching door
stoppers
Door stoppers onto the
Vertical supports .
G
H
4
Finished
front edge
G
H
4
G
H
X 2
Step 2
Attaching metal plates
& door hinges
G
Metal plates onto the
Door panels .
Insert the Door hinges
into the Door panels .
C
6
D
6
D
6
D
G
C
X 2
4
Page 6
Assembly Instructions
Step 3
a:
Attaching the side
panels
Insert Dowels into
a:
the
Shelf and Vertical
supports .
the Shelf .
3
4
supports onto
3
J
I
4
Finished
front edge
J
J
J
Finished
front edge
J
4
I
J
3
4
I
J
J
J
b:
Fix the
onto the Shelf .
p
3
2
b:
2
Finished
front edge
3
2
5
Page 7
Assembly Instructions
Step 4
a:
E
Attaching the door
panels
a:
Carefully locate the Door
panel onto the unit,
aligning the Door hinges
with the corresponding
holes.
Bottom panel onto the
unit.
Note:
Ensure the Door
hinges are aligned with
the corresponding holes.
6
E
1
Finished
front edge
E
1
E
6
E
b:
Carefully locate the Door
panel onto the unit,
aligning the Door hinges
with the corresponding
holes.
Top panel onto the unit.
Note:
Ensure the Door
hinges are aligned with
the corresponding holes.
6
E
1
b:
Finished
front edge
E
E
1
E
6
E
6
Page 8
Assembly Instructions
Step 5
Fixing back panel
Attach Back panels
5
onto the unit using Nails
F
.
Important:
The unit MUST
be ‘square’ when
back is attached.
back surface
F
5
5
back edge
21
Step 6
Attaching the handles
A
Handles onto the Door
panels .
B
6
B
6
6
A
A
B
7
Page 9
Assembly Instructions
Step
7
Attaching the screw
covers
Use
Screw covers to
cover the screw heads.
K
K
K
K
K
Step 8
Finishing the unit
Note:
It would be useful
to ask someone to help
you at the stage.
With help, place the unit in
the intended position.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
8
Loading...