Page 1
New Pagnell 3 Dr 4 Drw Wardrobe
Assembly Instructions
-
Please keep for future reference
605/8788
617/6127
607/9884
Dimensions
Width - 114.5cm
Depth - 54.5cm
Height - 180.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 08/11/16
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not use this item if any
components are missing or
damaged.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• To reduce
the likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load:
50 kgs (inside of wardrobe).
• Assembly of this product must
be carried out by a competent
adult.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6400800
Top panel (114.6 x 54cm)
1
Pilot holes for guidance only
Right side panel
2
Left side panel
3
(179 x 52cm)
Pilot holes for guidance only
(179 x 52cm)
Shelf x 2
7
Front bottom panel
8
Back bottom panel
9
Finished front surface
Front panel
10
Bottom support
11
(49.8 x 36.7cm)
Finished front edge
(111.2 x 11cm)
(111.2 x 11cm)
(111.2 x 7cm)
(111.2 x 7cm)
Center panel
4
Right middle panel
5
Pilot holes for guidance only
(170.4 x 51.9cm)
(73 x 51.9cm)
Back support
12
(73 x 11cm)
Pilot holes for
guidance only
Left middle panel
6
(51.9 x 36.7cm)
13
Door x 3
(138.1 x 36.1cm)
2
Page 4
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Large drawer front panel x 2
14
(72.4 x 14.5cm)
Large drawer bottom panel x 2
20
(70.7 x 33.6cm)
Large drawer back panel x 2
15
(69.8 x 11.5cm)
Drawer bottom panel x 2
21
(34.4 x 33.6cm)
Argos = 0345 6400800
Drawer front panel x 2
16
(36.1 x 14.5cm)
Drawer back panel x 2
17
(33.5 x 11.5cm)
Drawer right side panel x 4
18
(34 x 11.5cm)
Drawer left side panel x 4
19
(34 x 11.5cm)
Large back panel
22
Small back panel
23
(173.2 x 75.2cm)
(173.2 x 38.8cm)
3
Page 5
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases mor
may be supplied than are required.
A
Runner x 8
D
(This screw is included in
the door hinge bag)
15mm Screw x 36
G
30mm Dowel x 12
J
Plastic support x 8
M
50mm Screw x 17
P
30mm Screw x 16
B
(This screw is included
in the bag of runner)
12mm Screw x 24
E
Rail Support x 2
H
Door Stop x 2
K
14mm Screw x 18
N
Nail x 54
Q
Clothes rail x 1
C
Door hinge x 9
F
39mm Locking pin x 27
I
20mm Screw x 4
L
15mm Locking nut x 11
O
12mm Locking nut x 16
R
12mm Screw x 8
S
Door pad x 6
V
15mm Screw x 4
Y
Glue x 1
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
7mm Suitable drill bit
(for use with wall plug)
T
50mm Long dowel x 1
W
(This screw is
included in the
wall strap bag)
Wall strap x 2
Z
Ventilation holes cover x 4
Drill
x 2
U
Shelf support x 8
X
Wall plug x 2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
110 115 120 125 130 135 140 145 150 155 160 165 170
4
Page 6
Assembly Instructions
Step 1
a:
Attaching runners and
hinges
2
Middle hole
A
B
a:
Position Runners in
A
front edge of the Right
side panel .
2
Slide top of the Runners
A
back.
B
Runners on the Right
side panel .
Note:
A
2
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
D
Door hinges ‘back
C
plates’ onto the Right
side panel .
2
1.7cm
V
E
D
C
2
A
A
B
D
C
B
Finished
front edge
Pilot holes for
guidance only
V
E
D
C
D
C
V
Rail support on the
Right side panel .
b:
Slide top of Runners
A
forward and
E
2
B
b:
Middle hole
B B
A
2
.
2
B
B
B
B
Continued on next page.
5
A
A
Page 7
Assembly Instructions
Step 1 - continued
c:
c:
Position Runners in
front edge of the Left side
panel .
3
Slide top of the Runner
A
back.
A
1.7cm
B
Middle hole
3
A
D
B
Runners on the Left
side panel .
Note:
A
3
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
D
Door hinges ‘back
C
plates’ onto the Left side
panel .
d:
3
Slide top of Runners
A
forward and
B
.
d:
D
C
D
C
D
C
B
B
A
A
3
C
3
back edge
Pilot holes for
guidance only
B
Middle hole
A
B
Continued on next page.
3
A
A
B
B
B
B
6
Page 8
Assembly Instructions
Step 1 - continued
e:
Position Runners in
front edge of the Center
panel .
4
Slide top of the Runners
A
back.
B
Runners on the Center
.
panel .
A
4
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
D
Door hinges ‘back
C
plates’ onto the Center
panel .
Rail support on the
Center panel .
4
V
E
4
A
e:
BB
Middle hole
B
1.7cm
D
D
C
C
D
C
BB
AA
AA
Pilot holes for
guidance only
4
back edge
A
D
V
C
E
E
4
DEV
f:
Slide top of Runners
A
forward and
Continued on next page.
f:
B
.
BA
BA
4
BB
BB
BB
BB
B
4
Middle hole
A
B
7
Page 9
Assembly Instructions
Step 1 - continued
g:
Position Runners in
A
front edge of the Center
panel .
4
Slide top of the Runners
A
back.
B
Runners onto the
Center panel .
A
4
g:
4
Middle hole
A
B
1.7cm
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
h:
Slide top of Runners
A
forward and
B
.
A
h:
4
A
B
Finished
B
Pilot holes for
runner position
Middle hole
B
front edge
A
B
4
4
B
B
B
B
A
A
8
Page 10
Assembly Instructions
Step 2
Fitting locking pins
Screw Locking pins
F
into the Right side panel
, Left side panel
2
and Center panel .
Note:
Insert locking pins
3
4
as far as shown.
Do not over tighten.
F
F
2
F
F
F
F
F
3
F
F
F
F
4
F
9
Page 11
Assembly Instructions
Step 3
Fitting dowels
Insert Dowels and
Long dowel into Right
middle panel ,Left
middle panel ,Front
bottom panel and
Back bottom panel .
H
Stop onto the Right
middle panel .
G
T
5
6
8
9
I
5
T
I
5
H
Finished
front edge
G
Finished
front edge
8
G
G
G
G
G
G
Finished
front edge
9
G
G
6
I
H
G
Step
4
Attaching plastic
supports
a:
Plastic supports onto
the Front panel and
Bottom support .
b:
Front panel onto the
Front bottom panel .
Bottom support onto
K
J
10
11
K
10
8
K
11
the Back bottom panel
9
.
a:
b:
K
back surface
K
K
J
K
10
J
Finished
front surface
K
J
K
J
K
K
J
K
J
K
K
11
J
K
K
J
K
J
10
8
K
K
9
11
K
K
10
Page 12
Assembly Instructions
Step 5
Attaching right middle
panel
Note:
2 people are need
at this stage.
back edge
M
Right middle panel
5
onto the Center panel
.
4
Step 6
Attaching front bottom
panel
M
Front bottom panel
onto the Center panel
.
4
8
5
T
M
M
4
T
5
4
11
M
5
8
4
Page 13
Assembly Instructions
Step 7
Attaching back bottom
panel
M
bottom panel onto
the Center panel
9
.
4
4
Step 8
Attaching back
support
12
M
.
G
12
4
Insert Dowels into the
Back support .
support onto the
Center panel
M
9
Finished
G
front edge
12
M
4
12
Page 14
Assembly Instructions
Step 9
Attaching right side
panel
L
Position Right side panel
2
onto the unit.
Insert 5 Locking nuts
in the Back support ,
Right middle panel ,
Back bottom panel
L
12
5
9
and Front bottom panel
8
.
Use a screwdriver to turn
Locking nuts clockwise
L
to lock.
2
L
5
L
L
L
8
L
12
4
9
Step 10
Attaching left middle
panel
Position Left middle panel
6
onto the unit.
Insert 2 Locking nuts
into the Left middle panel
6
.
Use a screwdriver to turn
Locking nuts clockwise
L
to lock.
L
L
4
back edge
L
13
6
L
Page 15
Assembly Instructions
Step 11
Attaching left side
panel
Position Left side panel
3
onto the unit.
L
Insert 4 Locking nuts
L
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
L
to lock.
6
9
8
L
L
L
L
3
Step 12
Attaching top panel
a:
Door Stop onto the
Top panel .
Continued on next page.
I
H
1
a:
I
H
Finished
front edge
I
H
1
14
Page 16
Assembly Instructions
Step 12 - continued
b:
Top panel onto the
M
1
unit.
b:
M
M
back edge
M
1
2
4
3
M
M
M
M
Step 13
Fixing back panels
a:
Apart the Ventilation
holes covers rst.
Attach Ventilation holes
covers onto Large back
panel and Small back
panel , comebine the
22
23
covers.
Z
Z
a:
Z
Z
Z
Z
22
23
Continued on next page.
15
Page 17
Assembly Instructions
Step 13 -
b:
Attach Large back
panel and Small back
panel onto the unit
using Nails .
22
23
Important:
The unit MUST
be ‘square’ when
back is attached.
continued
N
b:
back surface
N
22
23
3
Step 14
Large drawers
assembly
a
:
Screw Locking pins
into 4 holes shown on
back of the Large drawer
front panel .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b:
Fix Drawer left side
panel onto the Large
14
19
drawer front panel .
F
14
a:
b:
9
F
F
F
F
14
19
F
Continued on next page.
14
16
Page 18
Assembly Instructions
Step 14 -
c:
Fix Drawer right side
panel onto the Large
drawer front panel .
Insert 2 Locking nuts
18
continued
14
O
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
O
to lock.
d:
Insert 2 Locking nuts
O
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
O
to lock.
c:
d:
18
14
back surface
O
19
O
O
Y
O
Place a small amount of
Y
Glue into the grooves.
Carefully slide the Large
drawer bottom panel
20
into the grooves.
e:
Place a small amount
of Glue into the groove
Y
on the Large drawer back
panel .
15
O
20
O
18
14
19
Y
e:
Y
Y
15
Continued on next page.
17
Page 19
Assembly Instructions
Step 14 -
f:
Position Large drawer
back panel onto the
unit using Screws .
Repeat with remaining
1 large drawer.
continued
15
P
Step 15
Drawer assembly
a
:
Screw Locking pins
into 4 holes shown on
back of the Drawer front
panel .
16
F
f:
a:
P
P
15
20
P
19
F
F
F
F
16
P
F
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b:
Fix Drawer left side
panel onto the
Drawer front panel .
c:
panel onto the
Drawer front panel .
Insert 2 Locking nuts
19
16
Fix Drawer right side
18
16
O
into the holes (they will
only insert one way).
b:
19
16
c:
O
18
Use a screwdriver to turn
Locking nuts clockwise
O
to lock.
Continued on next page.
16
19
O
O
18
Page 20
Assembly Instructions
Step 15 - continued
d:
Insert 2 Locking nuts
O
into the hole (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
to lock.
Place a small amount of
Y
Glue into the grooves.
Carefully slide the Drawer
bottom panel into the
grooves.
O
21
d:
d:
Y
back surface
21
O
O
18
19
16
Y
O
e:
Place a small amount
of Glue into the groove
on the Drawer back panel
17
.
f:
the unit using Screws .
Y
Position the Drawer
17
P
e:
e:
f:
f:
Y
Y
17
P
17
21
Repeat with remaining
1 drawer.
19
19
P
Page 21
Assembly Instructions
Step
16
Fixing to wall
Warning:
In order to prevent
overturning, this
product must be
used with the wall
attachment device
provided.
K
Wall straps(2 pcs) onto the
W
unit.
With help, move this product
into position.
Warning:
This product is
heavy.
Lift with care.
K
W
Top panel
W
Note:
Wall plugs supplied are
for solid wall only.
X
wall
be used for your wall, seek
professional advice if in doubt
W W X
remove this product .
Drill 2 holes and insert Wall
plugs(2 pcs) .
X
Warning:
Before drilling,
check wall for
hidden pipes and
and cables.
Reposition this product
Screws(2 pcs) .
W
20
Page 22
Assembly Instructions
Step 17
Inserting drawers
a:
Slide the drawers fully
onto the runners so the
runners butt up against
the back of the drawer
front.
b:
Fix through drawer
sides into the runners
R
using Screws .
a:
4
2
R
R
14
R
R
R
14
b:
c:
Slide the drawers fully
onto the runners so the
runners butt up against
the back of the drawer
front.
d:
Fix through drawer
sides into the runners
R
using Screws .
c:
R
d:
3
4
R
16
R
21
Page 23
Assembly Instructions
Step 18
Attaching hinges to
doors
Fix 3 Door hinges onto
the Doors using
Screws .
13
D
C
Step 19
Hanging doors
a:
With help, slot Door
hinges onto ‘hinge
plates’.
C
D
C
D
D
C
13
C
D
C
X 3
S
S
b:
Tighten screw shown
to lock hinges in position.
Repeat
a
and b for
opposite door.
See ‘Hinge adjustment
’
in step 20 if the doors
need adjusting.
Tear off the protective
backing from the Door
pads .
Stick the Door pads
onto the Doors .
S
S
13
S
13
S
C
C
S
S
C
13
C
13
C
S
S
C
C
a:
b:
C
C
22
Page 24
Assembly Instructions
Step 20
Hinge adjustment
a:
To move doors up or
down: loosen screws
shown and move doors
to suit.
Once doors are aligned,
re-tighten Screws .
D
a:
Door
D
b:
To move doors in or
out: loosen screw shown
and move doors to suit.
Re-tighten screws.
b:
Door
Continued on next page.
23
Page 25
Assembly Instructions
Step
c:
right: loosen screw shown
and move doors to suit.
Re-tighten screws.
20 -
To move doors left or
continued
c:
Door
24
Page 26
Assembly Instructions
Step 21
Attaching the shelves
a:
Place Clothes rail
onto Rail
b:
lnsert Shelf supports
U
into the unit. Ensure
supports .
Q
E
they are wall tted before
inserting the Shelves.
a:
Q
1
E
4
Q
2
Note:
Set the shelf
supports to the desired
height.
Slide the Shelves
onto the unit.
Tear off the protective
backing from the Door
S
pads .
Stick the Door pads
onto the front edge of
Shelves .
Note:
the glue to dry for 24
7
Before use allow
hours and make sure the
unit is secure.
Assembly is complete.
7
S
b:
S
Finished
front edge
U
7
S
7
S
S
3
U
U
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
25
Page 27
A Guide to -
Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important:
When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule:
if you are not sure.
2:
Ensure you use the recommended drill bit to match the wall
plug and hole size.
3:
Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4:
Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Always use a larger screw and wall plug
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...