New Pagnell Desk
Assembly Instructions -
Please keep for future reference
622/1168
618/7202
606/9447
Dimensions
Width - 100cm
Depth - 48.5cm
Height - 71.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 09/11/16
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not use this item if any
components are missing or
damaged.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• To reduce
the likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load:
50 kgs (top of desk).
• Assembly of this product must
be carried out by a competent
adult.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6400800
Table top (100 x 48cm)
1
Right side panel
4
(46 x 70cm)
Pilot holes
for guidance
only
Middle panel
5
(46 x 70cm)
Top support
2
Finished front edge
Bottom support
3
(58.5 x 11cm)
(58.5 x 11cm)
Left side panel
6
(46 x 70cm)
Front support
7
(36.7 x 11cm)
Back support
8
(36.7 x 11cm)
Front panel
9
(36.7 x 4.5cm)
Drawer front x 2
10
(36 x 14.4cm)
Drawer right side
11
x 2
(34 x 11.5cm)
Drawer left side
12
x 2
(34 x 11.5cm)
Drawer back
13
x 2
(33.5 x 11.5cm)
Drawer bottom
14
(33.6 x 34.4cm)
x 3
Large drawer
15
front
(36 x 33.6cm)
Large drawer right
16
side
(34 x 24cm)
Large drawer left
17
side
(34 x 24cm)
Large drawer back
18
(33.5 x 24cm)
Back panel
19
(60 x 39.4cm)
2
Components - Fittings
Note:
The quantities below are the correct amount to complete the assembly. In some cases mor
may be supplied than are required.
A
Runner x 6
D
Plastic support x 2
G
15mm Locking nut x 10
J
Nail x 12
M
30mm Screw x 12
B
(This Screw is included
in the bag of runner)
12mm Screw x 18
E
14mm Screw x 4
H
50mm Screw x 8
K
12mm Locking nut x 12
N
12mm Screw x 6
C
30mm Dowel x 13
F
39mm Locking pin x 22
I
Screw cover x 4
L
Glue x 1
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step 1
Attaching runners
a:
Position Runners in
A
front edge of the Right
side panel .
4
Slide top of the Runners
A
Runners on the
side panel .
.
B
A
4
Right
a:
4
A
Middle hole
A
A
A
B
B
1.7cm
B
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
b:
Slide top of Runners
A
forward and x as
shown using Screws .
Insert Dowels into the
C
Right side panel .
Screw Locking pins
B
4
F
into the Right side panel
.
4
b:
B
4
Finished
front edge
Middle hole
B
A
Pilot holes for
runner position
B
F
4
Note:
Insert locking pins
as far as shown.
Do not over tighten.
Continued on next page.
B
F
B
B
B
F
B
4
C
B
C
C
4
Assembly Instructions
Step - continued 1
c:
Position Runners in
A
front edge of the Middle
panel .
5
Slide top of the Runners
A
Runners on the Middle
panel .
Note:
.
B
A
5
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
c:
Finished
front edge
1.7cm
B
A
Middle hole
B
5
A
B
A
B
A
5
Pilot holes for
runner position
d:
Slide top of Runners
A
forward and x as
shown using Screws .
Insert Dowels into the
Middle panel .
C
5
B
d:
A
5
A
B
A
B
B
Middle hole
A
B
5
B
C
B
B
B
C
C
5
Assembly Instructions
Step 2
Fitting dowels and
locking pins
Insert Dowels into
a:
the Left side panel .
Screw Locking pins
C
6
F
into the Left side panel
.
6
Note:
Insert locking pins
as far as shown.
Do not over tighten.
a:
F
C
F
F
6
C
C
b:
Insert Dowels into
the Top support ,
Bottom support ,
Front support and
Back support .
C
2
3
7
8
b:
2
C
7
C
3
C
8
C
6
Assembly Instructions
Step 3
Attaching plastic
supports
a:
Plastic supports onto
the Front panel .
b:
Front panel onto the
Front support .
E
D
9
E
9
7
a:
b:
E
E
D
E
7
E
9
D
E
9
E
D
Step 4
Attaching bottom
panel and back
support
a:
Position Front support
7
and Back support
onto the Right side panel
4
.
Insert Locking nuts
into the Front support
and Back support .
Use a screwdriver to turn
Locking nuts
G
clockwise to lock.
8
G
7
8
G
back edge
G
G
4
8
7
7
Assembly Instructions
Step 5
Attaching middle panel
HH
a:
Middle panel onto the
unit.
Use Screw covers to
cover the screw heads.
H
5
I
a:
back edge
8
5
H
H
7
H
H
I
I
b:
Top support and
Bottom support onto
the Middle panel .
H
2
3
5
b:
H
H
H
2
3
5
Finished
front edge
8
Assembly Instructions
Step 6
Attaching left side
panel
Position Left side panel
6
onto the unit.
Insert 2 Locking nuts
into the Top support
and Bottom support .
Use a screwdriver to turn
Locking nuts clockwise
G
to lock.
G
2
3
G
G
G
2
3
back edge
6
Step 7
Attaching table top
a:
Screw Locking pins
into the Table top .
Insert Locking pins
Note:
as far as shown.
Do not over tighten.
b:
Then carefully locate
the Table top onto
1
the unit.
Insert 6 Locking nuts
into the unit.
F
1
G
a:
b:
F
F
F
F
F
1
4
F
G
F
back edge
1
Use a screwdriver to turn
Locking nuts clockwise
G
to lock.
Continued on next page.
9
G
5
G
G
G
6
Assembly Instructions
Step 8
Fixing back panel
Attach Back panel
onto the unit using Nails
J
.
Important:
The unit MUST
be ‘square’ when
back is attached.
19
J
19
8
4
5
1
Step 9
Drawer assembly
Screw Locking pins
a:
into 4 holes shown on
back of the Drawer front
10
.
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b:
Fix Drawer left side
onto the Drawer front .
F
12
10
a:
F
F
F
F
10
F
X 2
b:
12
Continued on next page.
10
X 2
10
Assembly Instructions
Step
c:
onto the Drawer front
11
.
10
Insert 2 Locking nuts
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
to lock.
d:
K
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
to lock.
Place a small amount of
Glue into the grooves.
9 -
continued
Fix Drawer right side
K
Insert 2 Locking nuts
K
L
K
c:
d:
K
11
12
10
K
X 2
K
14
K
11
L
12
L
Carefully slide the Drawer
bottom into the
grooves.
e:
of Glue into the groove
on the Drawer back .
f:
back onto the unit
using Screws .
14
Place a small amount
L
13
Position the Drawer
13
M
e:
f:
M
10
L
13
X 2
L
X 2
13
11
14
12
M
X 2
Assembly Instructions
Step 10
Large drawer
assembly
Screw Locking pins
a:
into 4 holes shown on
back of the Large drawer
15
front .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
b:
Fix Large drawer left
side onto the Large
17
drawer front .
Fix Large drawer right
c:
16
side onto the Large
drawer front .
15
15
F
a:
F
F
F
F
15
F
b:
17
15
c:
K
Insert 2 Locking nuts
K
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
K
to lock.
d:
Insert 2 Locking nuts
K
into the holes (they will
only insert one way).
Use a screwdriver to turn
Locking nuts clockwise
K
to lock.
Place a small amount of
L
Glue into the grooves.
Carefully slide the Drawer
bottom into the
14
grooves.
d:
16
17
15
K
K
K
14
K
K
16
L
15
L
17
Continued on next page.
12
Assembly Instructions
Step 10 - continued
e:
Place a small amount
of Glue into the groove
on
18
.
f:
drawer back onto the
unit using Screws .
L
the
Large drawer back
Position the Large
18
M
e:
f:
M
M
14
L
18
18
M
17
M
L
Step 11
Inserting large drawer
With help, carefully stand
desk upright.
Warning:
The Desk is heavy.
Lift with care.
a:
Slide the drawer fully
onto the runners so the
runners butt up against
the back of the drawer
front.
b:
Fix through drawer
sides into the runners
using Screws .
N
a:
N
N
N
b:
15
13
Assembly Instructions
Step 12
a:
Inserting drawers
a:
Slide the drawer fully
onto the runners so the
runners butt up against
the back of the drawer
front.
b:
Fix through drawer
sides into the runners
using Screws .
N
N
b:
10
N
N
10
N
N
Step 13
Finishing the unit
With help, place the unit
in the intended position.
Before use allow
Note:
the glue to dry for 24
hours and make sure the
unit is secure.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
14
Loading...