Assembly Instructions
After the sitting test,
c:
re - tighten bolts again,
if any adjustment needed.
c:
Ascot Chair
Assembly Instructions - Please keep for future reference
603/6432
603/6449
603/6456
d:
It is highly recommend
to re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep the
allen key to re - tighten
all bolts again when
required.
Assembly is complete.
d:
Dimensions
Width - 46cm
Depth - 52cm
Height - 96cm
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
7
Important
If you need help or have damaged or missing parts, call the
– Please read these instructions fully before starting assembly
Customer Helpline: 08456 400800
Issue 1 - 9/02/10
Safety and Care Advice
Assembly Instructions
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Maximum safe weight of
user: 110 Kgs.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Screw the lock seats
e:
D
with hand screw driver
by following the pre drilled
holes.
E
e:
E
Pre-drilled
hole
D
Step 2
Note : Stand the chair on
a level floor.
a:
Tighten all bolts.
b:
Sit on the chair to
the legs.
a:
b:
1
6
Assembly Instructions
c:
Stand the chair on a
floor. Insert bolts with
spring washers and
washers through side
C
rails holes into front leg
frame screw all bolts
3
by using ball allenkey .
A
B
G
c:
If you have damaged or missing components,
Components - Parts
call the
Customer Helpline: 08456 400800
Please check you have all the parts listed below
A
d:
Place the seat pad
2
on the table. Put the
chair frame on top of the
seat back.
d:
B
C
KCAB
5
3
7
1
2
Chair back x 1
4
6
1
3
F
Seat x 1
4
BACK
Right side rail x 1 Front leg frame x 1
Insert screw into
F
the pre - drilled holes on
the righ leg rail and
left leg rail using a
7
screwdriver.
5
7
6
6
1
2
6
BACK
5
Left side rail x 1
6
Right leg rail x 1
7
Left leg rail x 1
2
Components -
Fittings
Assembly Instructions
Please check you have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
Bolt x 8
D
Lock seat x 2
B
Spring washer x 8
E
Screw x 4
C
Washer x 8
F
38mm Screw x 4
G
Ball allenkey x 1
Tools required
Phillips screwdriver
(medium & large)
Step 1
a:
Put left side rail into
left side hole of the chair
back and right side rail
into right side hole.
Insert bolt with spring
washers and washers
through side rails holes
1
4
A
B
C
into the chair backs.
Screw all bolts by using
ball allenkey .
Insert screw into the
pre-drilled holes in the
right leg rail and
left legs rail tighten
6
7
(although not fully) with
a screwdriver.
5
G
F
a:
A
B
C
Left side rail
L
pre - drilled hole
BACK
5
Right side rail
4
7
BACK
6
1
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
Do not fully tighten.
Fit the front leg frame
b:
3
onto the right and left
4
side rails and right
and left leg rails .
5
6 7
and leg rails .
b:
F
R
3
5
7
4
BACK
6
3
4
Wow Madison Table
Assembly Instructions - Please keep for future reference 633/3221
Assembly Instructions - Please keep for future reference 633/3386
Dimensions
Length - 150cm
Width - 73cm
Height - 75cm
Important – Please read these instructions fully before starting assembly
Ｉｍｐｏｒｔａｎｔ – Ｐｌｅａｓｅ ｒｅａｄ ｔｈｅｓｅ ｉｎｓｔｒｕｃｔｉｏｎｓ ｆｕｌｌｙ ｂｅｆｏｒｅ ｓｔａｒｔｉｎｇ ａｓｓｅｍｂｌｙ
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Issue 1 - 12/09/12
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Components - Panels
Please check you have all the panels listed below
Leg x 4 (7.8 x 72.2cm)
2
underside
(150 x 73cm)
Top
1
If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
2
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
B C
70mm Bolt x 8 Assembly bolt x 4
D
E
13mm Nut x 8 Spring washer x 8
Tools required
Phillips screwdriver
(medium)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Washer x 8
F
13mm Spanner x 1
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
3
Assembly Instructions
Step 1
Fitting bolts
Insert assembly bolt
into leg . Screw bolts
A
into assembly bolt .
2
B
B
Repeat with remaining
legs .
2
2
B
A
A
A
Step 2
Attaching legs
Attach the four pieces of
2
legs to top using
washer , spring washer
E
and nut .
C
Tighten the bolts with
spanner .
F
With help, turn the
table over carefully.
Assembly is complete.
1
D
B
2
2
2
1
C
E
D
2
F
4
Loading...