Argos 6019435 ASSEMBLY INSTRUCTIONS

New Pagnell 2 Dr 2 Drw Wardrobe
Assembly Instructions
-
Please keep for future reference
601/9435
601/6524
601/8436
Dimensions
Width - 76cm
Depth - 54.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Version 1 Date: 08/11/16
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on the following pages.
• Remove all fi ttings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before starting.
• Do not use this item if any
components are missing or damaged.
• During assembly do not stand or put weight on the product,
this could cause damage.
Assemble the item as close to its fi nal position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your fl oor.
• During assembly children should be kept away from the product due to possible risk of
injury.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque setting.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with soap and water. This procedure should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
To reduce the likelihood of
damaging your product please ensure that your
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Handy Hints
Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts
• Regularly check and ensure that all bolts and fi ttings are tightend properly.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load: 50 kgs (inside of wardrobe).
• Assembly of this product must
be carried out by a competent adult.
Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Top panel (76.2 x 54cm)
1
Pilot holes for guidance only
Argos = 0345 6400800
Right side panel (179 x 52cm)
2
Left side panel
3
(179 x 52cm)
Pilot holes for guidance only
Middle panel
4
(73 x 51.9cm)
2
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Bottom panel
5
Bottom support (73 x 11cm)
6
Front panel
7
(73 x 11cm)
(73 x 7cm)
Argos = 0345 6400800
13
Drawer left side panel x 2
(34 x 11.5cm)
Drawer bottom panel x 2
14
(70.7 x 33.6cm)
Middle support
8
Door x 2 (138.2 x 36.1cm)
9
Drawer front panel x 2
10
Drawer back panel x 2 (69.8 x 11.5cm)
11
(73 x 11cm)
Pilot holes for guidance only
(72.3 x 14.4cm)
Drawer right side panel x 2
12
(34 x 11.5cm)
Back panel
15
(75.8 x 173.2cm)
3
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases mor may be supplied than are required.
A
Runner x 4
D
(This screws is included in the door hinge bag)
15mm Screw x 24
G
30mm Dowel x 14
J
Plastic support x 3
M
50mm Screw x 6
P
30mm Screw x 8
S
Door pad x 4
B
(This screw is included in the bag of runner)
12mm Screw x 12
E
Rail Support x 2
H
Door stop x 2
K
14mm Screw x 8
N
Nail x 30
Q
Clothes rail x 1
T
15mm Screw x 4
C
Door hinge x 6
F
39mm Locking pin x 18
I
20mm Screw x 4
L
15mm Locking nut x 10
O
12mm Locking nut x 8
R
12mm Screw x 4
U
(This screw is included in the wall strap bag)
Wall strap x 2
x 2
V
Wall plug x 2
W
Glue x 1
Tools required
Phillips screwdriver (medium & large)
Flatblade screwdriver (medium)
Drill
7mm Suitable drill bit (for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
X
Ventilation holes cover x 2
Small hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape measure
Eye protection (when using a hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
The screws length is measured from the head to the point (30mm screw shown).
4
Assembly Instructions
Step 1
a:
Attaching runners and hinges
2
Middle hole
A
B
a:
Position Runners
A
in front edge of the Right side panel .
2
Slide top of the Runner
A
back.
B
Runners on the Right side panel .
Note:
A
2
The front part of the runner should be approximately 1.7cm from the front edge of the panel.
D
Door hinges ‘back
C
plates’ onto the Right side panel .
Rail support on the Right side panel .
2
T
E
2
1.7cm
T
E
D
2
A
A
B
B
D
C
Finished front edge
Pilot holes for guidance only
C
T
E
D
D
C
C
b:
Slide top of Runners
A
forward and
Continued on next page.
b:
B
.
B
B
B
B
Middle hole
B
B
A
2
A
A
2
5
Assembly Instructions
Step 1 - continued
c:
c:
Position Runners in front edge of the Left side panel .
3
A
B
Middle hole
3
A
Slide top of the Runners
A
Runners on the
side panel .
Note:
.
B
A
3
Left
The front part of the runner should be approximately 1.7cm from the front edge of the panel.
D
Door hinges ‘back
C
plates’ onto the Left side panel .
Rail support on the Left
3
T
E
side panel .
3
1.7cm
D
D
C
D
C
B
B
A
A
Pilot holes for guidance only
C
3
back edge
D
T
C
E
Pilot holes for guidance only
T
E
d:
Slide top of Runners
A
forward and
d:
B
.
3
A
A
B
B
B
B
B
Middle hole
A
3
B
6
Assembly Instructions
Step 2
Fitting locking pins
Screw Locking pins into the Right side panel
and Left side panel
2
.
3
Note:
Insert locking pins as far as shown.
Do not over tighten.
F
F
F
F
F
F
F
F
F
F
2
F
3
Step 3
Fitting dowels
Insert Dowels into the Bottom panel , Bottom support , Middle support and Middle panel .
H
Stop onto the Middle panel .
4
G
5
6
8
4
I
F
G
5
G
G
6
I
G
G
G
G
G
I
H
H
8
G
4
G
G
G
7
Assembly Instructions
Step 4
a:
Attaching plastic supports
K
J
K
K
a:
Plastic supports onto the Front panel .
b:
Front panel onto the Bottom panel .
Step
5
K
J
7
K
7
5
b:
back surface
K
J
K
5
K
7
J
K
K
7
J
Attaching front panel
Note:
2 people are need at this stage.
Position Front panel and Bottom panel
7
5
onto the unit.
Insert Locking nuts
L
into the Bottom panel
5
.
Use a screwdriver to turn Locking nuts clockwise
L
to lock.
2
L
L
5
7
8
Assembly Instructions
Step 6
Attaching middle panel
Note:
2 people are needed at this stage.
Position Middle panel
4
onto the unit.
Insert 2 Locking nuts into the Middle panel .
L
4
Use a screwdriver to turn Locking nuts clockwise
L
to lock.
L
2
L
L
back edge
4
Step 7
Attaching back support and bottom support
Position Middle support
8
and Bottom support onto the unit.
6
Insert 2 Locking nuts into Middle support
and Bottom support . Use a screwdriver to turn
Locking nuts clockwise
L
to lock.
L
8 6
L
8
2
back edge
L
6
L
9
Assembly Instructions
Step 8
Attaching left side panel
Position Left side panel
3
onto the unit.
Insert 5 Locking nuts into the Bottom panel , Bottom support , Middle support and Middle panel .
4
L
5
6
8
Use a screwdriver to turn Locking nuts clockwise
L
to lock.
L
8
6
5
L
L
4
L
L
L
3
back edge
Step 9
Attaching top panel
a:
Door Stop onto the Top panel .
Continued on next page.
I
H
1
a:
I
I
H
1
H
Finished front edge
10
Assembly Instructions
Step 9 - continued
b:
Top panel onto the
M
1
unit.
b:
M
back edge
M
1
M
2
3
M
Step 10
Fixing back panel
a:
Apart the Ventilation holes covers rst. Attach Ventilation holes covers onto Back panel
, comebine the covers.
15
X
X
a:
X
X
15
Continued on next page.
11
Assembly Instructions
Step
b:
onto the unit using Nails
N
.
10 -
Attach Back panel
Important:
The unit MUST be ‘square’ when back is attached.
continued
15
b:
N
back surface
15
2
6
3
Step 11
Drawer assembly
Screw Locking pins
a:
into 4 holes shown on back of the Drawer front panel .
Note:
Insert Locking pins as far as shown.
Do not over tighten.
b:
Fix Drawer left side panel onto the Drawer front panel .
10
13
10
F
a:
b:
F
10
F
13
F
Continued on next page.
10
12
Assembly Instructions
Step 11 - continued
Fix Drawer right side
c:
12
panel onto the Drawer front panel .
Insert 2 Locking nuts
10
O
into the holes (they will only insert one way).
Use a screwdriver to turn Locking nuts clockwise
O
to lock.
d:
Insert 2 Locking nuts
O
into the holes (they will only insert one way).
Use a screwdriver to turn Locking nuts clockwise
O
to lock.
Place a small amount of
W
Glue into the grooves.
c:
d:
12
10
13
back surface
14
O
O
12
O
O
O
O
W
Carefully slide the Drawer bottom panel into the
14
grooves.
e:
Place a small amount of Glue into the groove
W
on the Drawer back panel .
11
f:
Position the Drawer back panel onto the unit using Screws .
11
P
e:
f:
10
W
11
P
14
11
13
W
W
Repeat with remaining 1 drawer.
13
13
P
Assembly Instructions
Step
12
Fixing to wall
Warning:
In order to prevent overturning, this product must be used with the wall attachment device provided.
K
Wall straps(2 pcs) onto the
U
unit.
With help, move this product into position.
Warning:
This product is heavy.
Lift with care.
K
U
Top panel
Note:
Wall plugs supplied are
for solid wall only.
V
U
wall
be used for your wall, seek professional advice if in doubt
U
Back panel
V
U
remove this product .
Drill 2 holes and insert Wall plugs(2 pcs) .
V
Warning:
Before drilling, check wall for hidden pipes and and cables.
Reposition this product
Screws(2 pcs) .
U
14
Assembly Instructions
Step 13
Inserting drawers and clothes rail
With help, carefully stand wardrobe upright.
Place Clothes rail onto Rail supports .
Warning:
The Wardrobe is heavy.
Lift with care.
a:
Slide the drawers fully
Q
E
onto the runners so the runners butt up against the back of the drawer front.
b:
Fix through drawer
sides into the runners
R
using Screws .
a:
R
Q
E
Q
b:
R
R
R
R
Step 14
Attaching hinges to doors
Fix 3 Door hinges onto Doors using Screws
.
D
9
Tear off the protective backing from the Door
S
pads .
Stick the Door pads onto the Doors
15
.
9
C
S
S
S
D
S
C
D
9
D
S
C
C
D
C
X 2
Assembly Instructions
Step 15
Hanging doors
a:
With help, slot Door hinges onto ‘hinge plates’.
b:
Tighten screw shown
to lock hinges in position.
C
C
9
Repeat opposite door.
See ‘Hinge adjustment in step 15 if the doors need adjusting.
a
and b for
Step 16
Hinge adjustment
a:
To move doors up or down: loosen screws shown and move doors to suit.
a:
b:
C
C
9
C
C
a:
D
Once doors are aligned, re-tighten Screws .
Continued on next page.
D
Door
16
Assembly Instructions
Step 16 -
b:
To move doors in or out: loosen screw shown and move doors to suit.
Re-tighten screws.
continued
b:
Door
c:
To move doors left or right: loosen screw shown and move doors to suit.
Re-tighten screws.
Note:
the glue to dry for 24 hours and make sure the
unit is secure.
Assembly is complete.
Before use allow
c:
Door
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
17
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs are supplied with your product:
- these are only suitable for use in masonry walls.
If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
Failure of the product due to
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not be used to support heavy loads, use
loads, general purpose wall plugs can be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on to plasterboard partitions.
Care & Maintenance
heavy loads such as shelving, wall cabinets and coat racks.
Safety: Always check the fitting and location to ensure your safety in and around the home.
For use with heavier loads such as TV & HiFi speakers and satelite dishes etc.
Fitting: From time to time check the fitting to ensure the wall plugs or screws do not become loose.
Revision 2 - 7/10/09
Loading...