Page 1
Assembly Instructions
Step 3
Winslow Bar stool
Note : Stand the chair on
a level floor.
Tighten all bolts.
a:
Note : Step 3 is essential
to prevent the chair from
wobbling caused by
uneven legs.
Sit on the chair to
b:
level the legs.
a:
b:
Assembly Instructions - Please keep for future reference
600/5580
600/5597
600/6280
600/6400
c:
After sitting test,
re - tighten bolts ,if
adjustment is needed.
d:
It is highly recommend
to re - tighten all the bolts
after using the chair for
7 days.
Note : Please keep
allen key to re - tighten
all bolts when required.
c:
d:
Dimensions
Width - 40cm
Depth - 53cm
Height - 100cm
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
7
Important
If you need help or have damaged or missing parts, call the
– Please read these instructions fully before starting assembly
Customer Helpline: 08456 400800
Issue 1 - 9/02/10
Page 2
Safety and Care Advice
Assembly Instructions
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Maximum safe weight of
user: 110 Kgs.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Fit the front stretcher
c:
7
rail to the right leg
3
and left leg .
4
c:
3
4
2
1
6
7
5
Turn over the chair.
d:
Screw the screw into
the pre - drilled holes on
the front stretcher rail
and the right side stretcher
rail and the left side
5
stretcher rail using
screwdriver.
E
7
7
d:
E
5
3
4
7
5
6
2
1
E
4
1
6
Page 3
Assembly Instructions
Components - Parts
If you have damaged or missing components,
call the
Customer Helpline: 08456 400800
Step 2
Attach left legs to
a:
front corners of the
seat frame. Use bolts
A
with spring washers
and washers into
B
each of the 2 holes
in the front corners.
Tighten bolts with allen
key .
F
Do not fully tighten.
4
C
a:
Please check you have all the parts listed below
A
4
2
1
5
6
B
C
2
1
Chair back x 1
Seat x 1
Attach right legs to
b:
front corners of the
seat frame. Use bolts
A
with spring washers
B
and washers into
each of the 2 holes
in the front corners.
Tighten bolts with allen
key .
F
Do not fully tighten.
C
Left leg x 1
Right leg x 1
3
3
b:
F
4
2
1
6
3
5
A
B
C
5
Right side stretcher rail x 1
4
6
Left side stretcher rail x 1
7
Front stretcher rail x 1
5
2
Page 4
Components -
Fittings
Assembly Instructions
Please check you have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
Bolt x 8
D
Wooden dowel x 2 Screw x 6
B
Spring washer x 8
E
C
Washer x 8
F
Allen key x 1
Tools required
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
Step 1
a:
Insert wooden dowels
D
into each centre hole
in the back of the seat
2
.
Insert bolts
b:
with spring washers
and washers through
the holes at the back of
the seat into the
chair back . Tighten
bolts with allen key .
A
B
C
2
1
F
a:
D
2
b:
A
Do not fully tighten.
Screw the screw into
the pre - drilled holes on
the right side stretcher rail
5
and the left side
stretcher rail using
screwdriver.
E
6
2
B
x 2
C
1
E
2
1
6
5
R
L
3
4
Loading...