Argos 600/0774, 600/0781 User guide

Gaslift Bar Table

Assembly Instructions - Please keep for future reference

600/0774

600/0781

Dimensions

Width - 53cm
Depth - 53cm
Height - 67~92.5cm

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the customer helpline: 08456 400800

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• We suggest you spend a short
time reading through this leaflet
and follow the simple step by
step assembly instructions.

• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.

Warnings

• This product should only be
used on firm, level ground.

Care and maintenance

• Please clean the table surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an

• Assemble this product on a
flat surface.

• Assemble all parts loosely
before tightening any bolts.

• Discard all extra fittings and
keep fittings out of reach of
children.

• Make sure the base remain in
contact with the ground.

appropriate polish.

• Do not use any abrasive
materials when cleaning.

• Unit weight : 7.5kg.

• We recommend that this unit is
assembled by at least 2 people.

• Retain Assembly Instructions
for future reference.

• Do not stand on the product.

• From time to time check that
there are no loose bolts on
this unit.

1

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Parts

Please check you have all the parts listed below

1

Table top

(Ø53 x 1.8cm)

2

Upper leg

(Ø5.6 x 16 x 39cm)

3

Gaslift

(Ø5 x 61~85cm)

4

Base

(Ø45 x 8.5cm)

2

If you have damaged or missing components,

Components - Fittings

call the customer helpline: 08456 400800

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.

A

M6 x 16mm Bolt x 4 Spring washer x 4

C

Washer x 4

B

Tools required

Crosshead
Screwdriver

Ruler - Use this ruler to help correctly identify the screws

105150 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115120 125 130 135 140 145 150 155 160 165 170

3

Assembly Instructions

Step 1

Attaching table top

Place the table top on

1

a flat protected surface.

Position the upper legs

2 1

on the table top as
shown. Align the holes
and fix together using

A

bolts & spring washers
& washers . Tighten

CB

the bolts using screw­driver.

Step 2

Attaching gaslift

Place the base on a
flat protected surface.

Insert the gaslift into
hole of the base .

4

3

4

A

B
C

2

A

A

A

B

B

C

1

B

C

C

3

1

2

Important:

Remove plastic
tip cover on gaslift
before assem­bling.

Step 3

Attaching table top

Position the table top
as shown and insert the
gaslift into the upper
leg . Secure by press­ing down the table top
firmly.

Gaslift operation

To adjust the table
higher, lift up the lever
under the table and
release at desired height.

3

2

4

2

3

Lever

To lower the table, lift up
the lever while pressing
down the table top.

If you need help or have damaged or missing parts, call the customer helpline: 08456 400800

4