Page 1
Gemini Barstool
Assembly Instructions - Please keep for future reference
600/0224
600/5054
Dimensions
Width - 52cm
Depth - 42cm
Height - 99cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/10/10
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• We suggest you spend a short
time reading through this leaflet
and follow the simple step by
step assembly instructions.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Assemble this product on a
flat surface.
Warnings
• Do not stand on the stool.
• Do not use the stool as a step
ladder.
Care and maintenance
• Assemble all parts loosely
before tightening any bolts.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Maximum safe weight of user:
110kgs.
• Unit weight: 5kg.
• Retain Assembly Instructions
for future reference.
• Do not sit with sharp objects
in back pockets as this may
damage the seat surface.
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Do not knock the surface of
the seat against sharp solid
surfaces.
• Please clean the seat surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
1
Page 3
Components - Parts
Please check you have all the parts listed below
1
Backrest
(51.5 x 14.5 x 28cm)
2
Seat
(40 x 40 x 5.5cm)
3
Stretcher
(Ø2.2 x 38 x 38cm)
5
Lower leg
(Ø2.2 x 72 x 49cm)
4
Upper leg
(Ø2.2 x 72 x 49cm)
2
Page 4
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C D
37mm Bolt x 4 30mm Bolt x 4 20mm Bolt x 6
E
F
G
Spanner x 1Allen key x 1Curved washer x 9
Ruler - Use this ruler to help correctly identify the screws
105150 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115120 125 130 135 140 145 150 155 160 165 170
Nut x 1
3
Page 5
Assembly Instructions
Step 1
Attaching legs
Position the upper leg
and lower leg as
shown. Align the holes
and fix together using
C D
bolt & nut .
Important:
Do not tighten
the bolt at this
stage.
5
C
4
D
4
5
C
4
5
D
Step 2
Attaching stretcher
Position the stretcher
between the legs as
shown. Align the holes
and fix together using
B
bolts with allen key .
Important:
Do not tighten
B
bolt at this
stage but tighten
C
bolt with nut
using allen key
and spanner .
3
F
D
F
G
C
D
4
3
4
5
B
B
B
3
B
B
4
Page 6
Assembly Instructions
Step 3
Attaching seat
Place the seat on a
flat protected surface.
Position the legs on the
seat as shown. Align the
holes and fix together
using bolts & curved
washers . Tighten the
E
bolts using allen key .
2
A
F
A
5
4
A
E
A
A
E
E
5
A
E
E
2
Step 4
Aligning the legs
Carefully turn over and
place on a flat surface.
Tighten the bolts on the
stretcher using allen
key while making
adjustments to ensure
the legs are even on the
floor.
Attaching backrest
Turn over the barstool
again to easily assemble
the backrest to the
seat as shown. Align
the holes and fix
together using bolts &
curved washers .
Tighten the bolts using
allen key .
3
F
1
2
E
F
2
F
3
C
C
E
E
CC
E
2
C
C
E
E
2
C
E
Assembly is complete.
1
1
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
5
Loading...