Page 1
Adult Malibu - Single Bedside
Assembly Instructions - Please keep for future reference
CR
532/9717
555/1231
565/5814
565/6291
553/2803
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Dimensions
Width - 38.3cm
Depth - 39.6cm
Height - 44.6cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
MADE IN
BRITAIN
Issue 2 - 24/05/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 10kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Care and maintenance
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it must be
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any
protective film before use
1 2 3
Left Side
(43.1 x 39.4cm)
(DF7343)
Right Side (DF7344)
(43.1 x 39.4cm)
5 6 7
Plinth (DF6021)
(34.9 x 9.2cm)
Back Rail (DF6022)
(34.9 x 6cm)
Top (DF6020)
(38.3 x 39.6cm)
Cross Rail (DF6023)
(34.9 x 6cm)
4
Shelf (DF7345)
(34.9 x 39.2cm)
Drawer Front (DF6025)
8 9 10
(34.3 x 15.7cm)
11
Drawer Back (W300-130)
(30 x 13cm)
Left Drawer Side (W350-130LH)
(35 x 13cm)
Drawer Base (T311-347)
12
(31.1 x 34.7cm)
Right Drawer Side (W350-130RH)
(35 x 13cm)
Back (X375-350)
13
(37.5 x 35cm)
2
Page 4
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Quickfit dowel
(F545) x 14
D E
19mm
Screw (F461) x 1
G
Wooden dowel (F22) x 16
J
Nail (F51) x 12
350mm long
a
L
CL
CL Runner
(F422) x 1
B
Large locking cam nut (F607) x 14
Wedgefix (F639) x 2
H
9mm Screw (F73) x 6
K
Handle
(F418) x 1
C
Knock-in Peg
F
13mm Screw
I
Plastic Nail
(F91) x 4
(F171GY) x 4
(F63) x 6
b
L
CR
CR Runner (F424) x 1
c
L
DL
DL Runner (F425) x 1
d
L
DR Runner
(F426) x 1
DR
Tools required
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
Page 5
Assembly Instructions
Step 1
Prepare the drawer
sides
a: Insert a large locking
cam nut into the left
drawer side . and the
right drawer side .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
B
9
10
a:
B
b:
B
9
B
10
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
side and the right
drawer side .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
9
10
Step 2
Fit the drawer sides
to the drawer front
9
A
B
A
10
A
Push the left drawer side
. and right drawer side
9
. down onto the back
10
of the drawer front .
8
Turn the large locking
cam nuts clockwise
B
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
10
A
9
8
B
4
Page 6
Assembly Instructions
Step 3
Fit the drawer base
Slide the drawer base
12
down the grooves in the
drawer sides and
109
and down into the
groove in the drawer
front .
8
Step 4
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
9 10
Make sure that the
drawer base fits into
12
the groove in the drawer
11
back .
11
12
9
10
9
8
C
C
11
C
12
C
9
910
Hold the drawer back
11
in position and tap the
knock-in pegs
C
through the holes in the
drawer sides and .
9 10
Step 5
Fit the handle
Attach the handle to
the drawer front
using screw .
K
8
D
D
8
K
5
Page 7
Assembly Instructions
Step 6
Fit the wedgefixes
E
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
E
E
E
Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.
Step 7
Fit runners to the
drawer
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
8
to mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
L c
9
F
L d
10
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Runners must be
pushed up against
the drawer front
F
F
7
F
DL
8
F
9
DR
DL
L d
L c
6
Page 8
Assembly Instructions
Step 8
Prepare the left side
a: Fit the CL runner
to the left side .
The 1st screw uses
H
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
H
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
L a
c: Insert 2 large locking
cam nuts into the left
side .
B
1
L a
1
F
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
1st
front edge
Finished
Finished
front edge
a:
front edge
Finished
H
screw
L a
CL
H
H
H
CL
L a
1
F
Push 2 of the quickfit
dowels as far as they
A
will go into the left side
. .
1
Tap 2 wooden dowels
into the left side .
G
1
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Finished
front edge
b:
c:
Finished
front edge
F
CL
CL
1
B
B
A
G
B
1
G
A
10mm
A
G
7
Page 9
Assembly Instructions
Step 9
Prepare the right side
a: Fit the CR runner
to the right side .
The 1st screw uses
H
L b
2
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
H
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
F
the hole at the top of the
runner .
L b
c: Insert 2 large locking
cam nuts into the
right side .
B
2
a:
1st
screw
L b
CR
H
H
H
CR
2
L b
H
Finished
front edge
F
front edge
Finished
front edge
Finished
Push 2 of the quickfit
dowels as far as they
A
will go into the right side
. .
2
Tap 2 wooden dowels
into the right side .
G
2
b:
c:
F
2
CR
Finished
front edge
B
A
G
B
2
CR
G
A
B
A
Finished
front edge
8
Page 10
Assembly Instructions
Step 10
Prepare the shelf
Insert 4 large locking
cam nuts into the
shelf .
B
4
Push 4 of the quickfit
dowels as far as they
will go into the shelf .
Tap 4 wooden dowels
into the shelf .
A
4
G
4
Step 11
Fit the shelf onto the
left side
Push the shelf down
onto the left side .
4
1
A
B
A
G
Finished
front edge
B
A
G
B
B
4
B
A
Carcase Assembly
hps://www.youtube.com/watch?v=9C7tgv5xnbE
Finished
front edge
Finished
front edge
4
A
G
G
Turn the 2 large locking
cam nuts clockwise
B
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 12
Prepare the cross rail
Tap 4 wooden dowels
into the cross rail .
G
7
Step 13
Fit the cross rail onto
the left side
G
G
Finished
front edge
Finished
front edge
CL
1
Note: The cross rail has no
7
7
holes drilled on either surface
G
G
Push the cross rail
7
down onto the left side
. .
1
9
CL
1
Page 11
Assembly Instructions
Step 14
Prepare the plinth
Insert 2 large locking
cam nuts into the
plinth .
B
5
Push 2 of the quickfit
dowels as far as they
will go into the plinth .
Tap 2 wooden dowels
into the plinth .
A
5
G
5
Step 15
Fit the plinth
A
B
B
A
G
5
B
A
G
Push the plinth down
onto the left side .
5
1
Turn the large locking
cam nut clockwise as
B
far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 16
Prepare the back rail
Insert 2 large locking
cam nuts into the
back rail .
Push 2 of the quickfit
dowels as far as they
will go into the back rail
6
.
Tap 2 wooden dowels
into the back rail .
B
6
A
G
6
5
CL
1
A
B
B
A
G
6
B
A
G
10
Page 12
Assembly Instructions
Step 17
Fit the back rail
Push the back rail
6
down onto the left side
1
. .
Turn the large locking
cam nut clockwise as
B
far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 18
Fit the right side
Push the right side
down onto the assembly.
Turn the 4 large locking
cam nuts clockwise
B
as far as they will go to
secure the panels.
2
CL
1
Finished
front edge
6
2
CL
Important: Make sure
there is no gap between
the fitted panels.
Carefully stand the
unit up for the next
step.
Step 19
Fit the top
Push the top down
onto the assembly.
Turn the 4 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
3
B
3
Finished
front edge
CR
11
Page 13
Assembly Instructions
Step 20
Fit the back
Carefully lay the unit
down onto its front
edges for this step.
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
J
Nail around the
outside edges of the
13
back .
Note: Nails should be
spaced out evenly.
13
Squaring up a Chest and tting the Back Panel
www.youtube.com/watch?v=FeaI6541z7o
The measurement from top corner X to bottom corner X must be
a:
equal to the measurement from top corner Y to bottom corner Y
b:
J
x
x
y
y
13
CR
xx
y
Step 21
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
2
Carefully stand the
unit up for the next
step.
I
1
I
I
2
CR
I
I
1
12
Page 14
Assembly Instructions
Step 22
Fit the drawer
Slide the wheels of the
runners fitted to the
drawer, over the wheels
of the runners fitted to
the side panels and push
the drawer into position.
Assembly is complete
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
CR
Side
panel
Drawer
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
13
Page 15
Page 16
ALR3316
Loading...