How it Works
Argos
Loading...
5532724
ASSEMBLY INSTRUCTIONS
20 pgs7.38 Mb0

Argos 5532724 ASSEMBLY INSTRUCTIONS

Download
Adult Malibu - 3+2 Wardrobe
Assembly Instructions - Please keep for future reference
CR
More help is available throughout this booklet by scanning
Dimensions
Width - 74.8cm
Depth - 49.8cm
Height - 180.5cm
CR
CR
in the QR codes or typing in the links
MADE IN
BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 1 - 18/05/16
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs approximately 50kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1 to 4.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
Care and maintenance
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
• Safety note: To prevent possible overbalancing this unit must be secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
Tools required
Rule
Rule
Spirit level
ScissorsSquare
• From time to time check that there are no loose screws on this unit.
Eye protection (when using a hammer or drill)
Hammer Bradawl
Cross-head screwdriver
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Electric drill (only use when drilling into walls)
Step ladder
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
3
Top (DF6014)
(74.8 x 49.8cm)
Horizontal (DF5862)
4
(71.4 x 47.2cm)
Hanging Rail
5
Left Side (DF6010)
1 2
(179 x 49.6cm)
Right Side (DF6011)
(179 x 49.6cm)
(70.8cm long)
When applicable, remove any protective film before use
6
Plinth (DF5856)
(71.4 x 9.2cm)
(FHR708)
Cross Rail
7
(71.4 x 6cm)
Back Rail
8
(71.4 x 9.2cm)
(DF5858)
x 2
(DF5866)
x 2
Drawer Front (DF5996)
9 10 11 12
(70.8 x 15.7cm)
Drawer Base
13
(67.6 x 44.7cm)
x 3
(T676-447)
x 3
Drawer Back
(66.5 x 13cm)
14 15
Left Door
(119.6 x 35.25cm)
(W665-130)
x 3
(DF6012)
Left Drawer Side
(WB450-130LH)
(45 x 13cm)
x 3
Right Door (DF6013)
(119.6 x 35.25cm)
16
Back (X1709-740)
(170.9 x 74cm)
Right Drawer Side
(WB450-130RH)
(45 x 13cm)
x 3
2
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel
D E
19mm
Screw (F461) x 6
(F545) x 6
Main Fittings Bag
A
Quickfit dowel
F
13mm Screw
(F545) x 14
(F63) x 6
B
Large locking cam nut (F607) x 6
13mm Screw (F79) x 6
B
Small locking cam nut (F607) x 14
13mm Screw (F52) x 4
C
Knock-in Peg
F
13mm Screw (F63) x 12
D
19mm
9mm Screw (F73) x 18
Screw (F461) x 2
HG
(F171GY) x 12
I
Nail (F51) x 34
L
Door Buffer (F137) x 4
J
Plastic Nail
M
Wooden dowel (F22) x 26
(F91) x 5
K
Rail Holder (F891) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
Components - Fittings
Individual Fittings Bags
N
Overbalance protector
F474) x 1
kit (
O
Handle
(F418) x 8
P
Pre-mounted hinge (
Q
Drawer Brace (F427) x 3
M
R
R
R
a
b
c
CL
DL
F419) x 6
436mm long
450mm long
CL Runner
CR
CR Runner
DL Runner
(F608) x 3
(F609) x 3
(F610) x 3
d
R
DR
DR Runner
(F611) x 3
4
Assembly Instructions
Step 1
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7
Prepare the drawer sides
a: Insert a large locking
cam nut into the left drawer sides and the right drawer sides .
Note: The arrow on the locking cam nut must point towards the hole in the end of the panel.
B
11
12
b: Push 1 of the quickfit
dowels as far as it will go into the 6 left drawer sides and the 6 right drawer sides .
A
11
12
Standard Drawer Box Assembly
hps://www.youtube.com/watch?v=HclfJdkm-Lg
a:
B
b:
B
11
12
x 3 x 3
B
Note: Only the plastic thread of the quickfit dowel sticks out from the panel.
Step 2
Fit the drawer sides to the 3 drawer fronts
Push the left drawer sides . and right drawer sides . down onto the back of the 3 drawer fronts .
Turn the large locking cam nuts clockwise as far as they will go to secure the panels.
11
12
9
B
A
B
x 3
11
A
12
x 3 x 3
12
A
Important: Make sure there is no gap between the fitted panels.
5
11
9
Assembly Instructions
Step 3
Fit the drawer bases
Slide a drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
9
13
1211
Step 4
Fit the drawer backs
Fit a drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
11 12
10
10
13
13
12
x 3
11
x 3
C
C
11
9
C
C
10
12
13
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
C
11 12
10
Step 5
Fit the handles
Attach 2 handles to each drawer front using screws .
O
9
D
D
D
9
O
O
x 3
6
Assembly Instructions
Step 6
E
Fit the drawer braces
x 3
Turn the 3 drawer assemblies over and hook a drawer brace onto the bottom edge of the drawer back .
Fix it to the drawer front and drawer back using 2 screws .
E
Q
10
Q
E
E
Q
10
E
Q
Step 7
Fit runners to the drawers
Fit the DL runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit the DR runner to the bottom edge of the right drawer side using the same method.
9
R c
11
F
R d
12
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Runners must be
pushed up against
the drawer front
F
F
DL
9
F
DL
11
x 3
F
12
DR
R d
R c
7
Assembly Instructions
Step 8
Prepare the left side
a: Fit 3 CL runners
to the left side .
The 1st screw uses the 1st hole in from the front of the runner.
The 2nd and 3rd screws
H
. use the holes that line up with the other panel holes.
b: Fit a screw into
the hole at the top of the runner .
Fit a rail holder , to the left side using 2 screws .
R a
1
G
R a
1
H
F
K
front edge
Finished
a:
Use the Main Fittings Bag for Steps 8 - end
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
1st
H
screw
R a
CL
Finished
front edge
H
H
H
H
CL
CL
H
H
CL
H
H
H
R a
R a
R a
1
c: Insert 2 large locking
cam nuts into the left side .
Push 2 of the quickfit dowels as far as they will go into the left side
1
. .
Tap 3 wooden dowels into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
B
1
A
M
1
front edge
Finished
b:
c:
CL
CL
F
F
front edge
CL
F
CL
CL
Finished
F
CL
Finished
front edge
1
G
G
K
1
B
A
B
A
M
M
M
A
10mm
M
B
8
Assembly Instructions
Step 9
1st
Prepare the right side
a: Fit 3 CR runners
to the right side .
R b
2
CR
screw
R b
H
front edge
Finished
The 1st screw uses
H
the 1st hole in from the front of the runner.
The 2nd and 3rd screws
H
. use the holes that line up with the other panel holes.
b: Fit a screw into
F
the hole at the top of the runner .
Fit a rail holder , to the right side using 2 screws .
R b
K
2
G
c: Insert 2 large locking
cam nuts into the right side .
Push 2 of the quickfit dowels as far as they will go into the right side
2
. .
B
2
A
a:
b:
F
H
front edge
H
H
H
H
H
CR
Finished
CR
R b
2
Finished
front edge
G
G
K
2
Finished
front edge
H
H
H
CR
CR
R b
R b
F
F
F
CR
CR
Tap 3 wooden dowels into the right side .
9
M
2
c:
CR
CR
CR
A
B
2
Finished
front edge
B
A
B
M
M
M
A
Assembly Instructions
Step 10
Prepare the horizontal
Insert 4 large locking cam nuts into the horizontal .
B
4
Push 4 of the quickfit dowels as far as they
A
will go into the horizontal . .
4
Tap 6 wooden dowels into the horizontal .
M
4
Step 11
Fit the horizontal to the right side
B
A
M
M
M
A
B
B
4
Finished
front edge
A
Carcase Assembly
hps://www.youtube.com/watch?v=9C7tgv5xnbE
B
A
M
M
M
Push the horizontal onto the right side .
4
2
Turn the 2 large locking cam nuts clockwise
B
as far as it will go to secure the panels.
Important: Make sure there is no gap between the fitted panels.
Step 12
Prepare the 2 cross rails
Tap 4 wooden dowels into each of the 2 cross
7
rails .
M
M
M
2
Finished
front edge
CR
CR
CR
4
Finished
front edge
x 2
7
Finished
front edge
Note: The cross rails have no holes drilled on either surface
M
M
10
Assembly Instructions
Step 13
Fit the 2 cross rails to the right side
Push the 2 cross rails onto the right side as
7
2
shown.
2
7
Finished
front edge
CR
CR
CR
7
Finished
front edge
Step 14
Prepare the 2 plinths and the back rail
Insert 2 large locking cam nuts into the each of the 2 plinths and the back rail . .
Push 2 of the quickfit dowels as far as they will go into the each of the 2 plinths and the back rail . .
Tap 2 wooden dowels into the each of the 2 plinths and the back rail . .
B
6
8
A
6
8
M
6
8
M
M
B
A
B
6
x 2
A
M
Note: The 2 plinths and the
B
A
Finished
top edge
8
back rail are similar but, the back rail has a finished top edge
B
11
A
M
Assembly Instructions
Step 15
Fit the 2 plinths and the back rail
Push the 2 plinths and the back rail onto the right side .
Turn the 3 large locking cam nuts clockwise
B
as far as they will go to secure the panels.
Important: Make sure there is no gap between the fitted panels.
6
8
2
CR
6
CR
CR
6
Finished
top edge
2
8
Note: Support these 2 panels until the left side is fitted in the next step
Step 16
Fit the left side
Push the left side onto the assembly.
Turn the 5 large locking cam nuts clockwise
B
as far as they will go to secure the panels.
Important: Make sure there is no gap between the fitted panels.
1
CR
CR
CR
CR
CR
CR
1
Finished
front edge
12
Assembly Instructions
Step 17
Fit the top
Push the top onto
3
the assembly.
Turn the 4 large locking cam nuts clockwise
B
as far as they will go to secure the panels.
Important: Make sure there is no gap between the fitted panels.
3
CR
CR
CR
CR
CR
CR
Finished
front edge
Step 18
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
I
outside edges of the
16
back .
Note: Nails should be spaced about 150mm apart.
16
yy
Squaring up a Robe and tting the Back Panel
www.youtube.com/watch?v=udEKmXmPEW0
The measurement from top corner X to bottom corner X must be
a:
equal to the measurement from top corner Y to bottom corner Y
x
b:
CR
I
16
17
16
CR
CR
x
x
CR
CR
CR
x
y
y
13
Assembly Instructions
Step 19
Fit the 5 plastic nails
Tap 2 plastic nails
J
into the bottom edge of each side and .
1
2
Tap the remaining plastic nail into the bottom
J
edge of the plinth at
6
the front of the unit.
J
J
Carefully stand the unit up for the next step and place it in its final position in the room.
17
2
CR
J
CR
CR
J
6
J
1
CR
CR
CR
Warning: The unit is heavy. Lift with care.
14
Assembly Instructions
Step 20
Fit the overbalance protector kit
a:
a: Before fitting the
overbalance protector kit, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level.
a: To prevent possible
overbalancing this unit must be secured to a suitable wall by fitting of the overbalance protector kit to the unit, or an alternative fixing method of your choice.
N
b:
N
N
Wall fixings are not supplied as they will need to suit the wall type.
Take care when
Note:
drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
CR
CR
CR
15
Assembly Instructions
Step 21
Fit the hanging rail and drawers
Push the hanging rail into the rail holders fitted to the side panels.
Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.
5
K
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
5
CR
CR
CR
Side
panel
5
K
Drawer
Step 22
Prepare the 2 doors
Push fit 3 hinges into each door and .
14 15
Secure each hinge by tighteng up its 2 screws.
P
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
P
P
L
14
P
P
15
P
P
16
Assembly Instructions
Step 23
Fit the doors and the handles
2 people are needed here
Fit 1 door and at a time, by lining up the 2 screws in the top hinge with the 2 holes at the top of the panel and push them in.
Working down the door, push in the other hinges.
When all of the hinges have been pushed into place, tighten the 2 screws on each hinge.
Attach a handle to each door using screw . .
D
14 15
P
O
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
Press the screws into
the holes in the panels
P
When the hinges have
been pushed in,
tighten up their screws
P
Note: Fit the top hinge 1st
Warning: The doors are heavy. Lift with care.
14
15
O
D
O
CR
CR
CR
17
Assembly Instructions
Step 24
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
a:
b:
A
A
c:
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
B
d:
C
18
Assembly Instructions
Step 25
Fit the door buffers
Stick a door buffer
L
into the top and bottom corner of each of the 2 doors and .
14 15
Assembly is complete
14
L
15
CR
CR
CR
L
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020
19 ALR3297
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use