Malibu - 5+2 Drawer Chest
Assembly Instructions - Please keep for future reference
CR
CR
CR
CR
CR
CR
CR
558/8228
539/6173
544/1341
541/5566
542/1907
WARNING!
In order to prevent overturning, this product must be
used with the wall attachment device provided
Dimensions
Width - 74.8cm
Depth - 39cm
Height - 108.6cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
MADE IN
BRITAIN
Issue 5 - 06/10/16
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 38kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Care and maintenance
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance protector
kit supplied or, an alternative
fixing method of your choice.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
When applicable, remove any protective film
from the panels before they are used
Tools required
Rule Scissors Hammer
Cross-head
screwdriver
Eye protection
(when using a
hammer or drill)
Electric drill
(do not use for
fitting screws)
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
1
Left Side
(107.1 x 39.4cm)
(DF6786)
2 4
Right Side (DF6787)
(107.1 x 39.4cm)
When applicable, remove any
protective film before use
3
Top (DF6780)
(74.8 x 39.6cm)
Divider
(16 x 37.3cm)
(DF6781)
Plinth (DF5856)
5
(71.4 x 9.2cm)
8
Small Left Drawer
Front
(DF6782)
(35.25 x 15.7cm)
Left Drawer Side
11 12
(35 x 13cm)
14
Large Drawer Back (W665-130)
(66.5 x 13cm)
x 7
(WB350-130LH)
x 5
6 7
9 10
16
Cross Rail (DF5858)
(71.4 x 6cm)
Small Right Drawer
Front
(DF6783)
(35.25 x 15.7cm)
Right Drawer Side
(35 x 13cm)
x 7
Large Drawer Base
(67.6 x 34.7cm)
x 5
(WB350-130RH)
(T676-347)
Back Rail
(71.4 x 6cm)
(DF5857)
x 2
Large Drawer Front (DF5996)
(70.8 x 15.7cm)
13
Small Drawer Back
(30 x 13cm)
x 5
x 2
(W300-130)
Small Drawer Base
15
(31.1 x 34.7cm)
x 2
(T311-347)
17
Back
(98.9 x 74cm)
(DF6788)
2
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel
(F545) x 14
D
19mm
Screw (F461) x 12
Main Fittings Bag
A
Quickfit dowel
H
Wooden dowel (F22) x 16
(F545) x 12
B
Large locking cam nut (F607) x 14
E
15mm Screw
(F284) x 10
B
Large locking cam nut (F607) x 12
I
9mm Screw (F73) x 42
F
13mm Screw
J
Plastic Nail
(F91) x 5
C
Knock-in Peg
(F63) x 28
F
13mm Screw
(F171GY) x 28
G
Wedgefix
(F639) x 4
(F63) x 14
K
Nail (F51) x 24
Individual Fittings Bags
L
Drawer Brace (F420) x 5
a
N
b
N
c
N
d
N
3
CL
DL
336mm long
350mm long
CL Runner
(F422) x 7
CR Runner (F424) x 7
DL Runner (F425) x 7
DR Runner
(F426) x 7
M
Handle
(F418) x 12
O
CR
Overbalance protector
F474) x 1
kit (
DR
Assembly Instructions
Step 1
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 14
Prepare 5 pairs of
drawer sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
B
11
12
Standard Drawer Box Assembly
hps://www.youtube.com/watch?v=HclfJdkm-Lg
a:
B
B
B
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the 5 left drawer
sides and the 5 right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
11
12
b:
A
11
12
x 5 x 5
11
A
12
x 5 x 5
A
Step 2
Fit the drawer sides
to the 5 large drawer
fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 5
large drawer fronts .
Turn the large locking
cam nuts clockwise
to the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
11
12
10
B
B
Edge Edge
Turn to “2 o’clock”
x 5
11
Edge
12
10
4
Assembly Instructions
Step 3
Fit the large drawer
bases
Slide a large drawer base
. down the grooves in
16
the drawer sides and
. and down into the
12
groove in the large
drawer front .
11
10
Step 4
Fit the large drawer
backs
Fit a large drawer back
between the drawer
sides and .
Make sure that the large
drawer base fits into
the groove in the large
drawer back .
11 12
16
14
14
Standard Drawer Box Assembly
hps://www.youtube.com/watch?v=HclfJdkm-Lg
16
12
x 5
11
10
C
x 5
14
C
11
C
16
12
9
C
Hold the large drawer
back in position and
14
tap the knock-in pegs
through the holes in the
drawer sides and .
11 12
C
Step 5
Fit the handles
Attach 2 handles to
each large drawer front
. using screws .
10
M
D
Step 6
Fit the drawer braces
Turn the 4 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
L
14
D
D
10
M
E
10
L
E
E
L
x 5
M
x 5
Important: Make sure
that the drawer assembly
is square before fitting
the drawer brace.
Fix it to the drawer front
10 14
. and drawer back
using 2 screws .
5
E
14
E
L
Assembly Instructions
Step 7
Prepare 2 pairs of
drawer sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
B
11
12
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
side and the right
drawer side .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
11
12
a:
b:
A
B
B
11
B
12
x 2 x 2
11
A
12
A
x 2 x 2
Step 8
Fit the drawer sides
to the small drawer
fronts
Push the left drawer side
. and right drawer side
11
12
. down onto the back
of the small drawer
fronts and .
Turn the large locking
cam nuts clockwise to
the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
8 9
B
B
Edge Edge
Turn to “2 o’clock”
12 12
11
8
Edge
Note: The small right drawer
front has a small identification
hole (see panels page).
9
11
9
6
Assembly Instructions
Step 9
Fit the small drawer
bases
Slide a small drawer
base down the
15
grooves in the drawer
sides and and
down into the groove in
the small drawer front
and .
9
1211
8
Step 10
Fit the small drawer
backs
Fit a small drawer back
between the drawer
sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
11 12
15
13
13
C
15
11
x 2
11
C
8 9
13
15
12
12
9
x 2
C
C
Hold the small drawer
13
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
11 12
C
Step 11
Fit the handles
Attach a handle to
each small drawer front
8 9
. and using screws
D
. .
M
Step 12
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
G
D
x 2
M
8 9
Important: Make sure
that the drawer assembly
is square before fitting
G
x 2
G
the wedgefixes.
G
7
Assembly Instructions
Step 13
Fit runners to the 5
large drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front. Use a bradawl to
mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
N c
11
F
N d
12
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Runners must be
pushed up against
the drawer front
F
F
F
DL
11
DL
N c
x 5
F
12
DR
N d
Step 14
Fit runners to the 2
small drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front. Use a bradawl to
mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
N c
11
F
N d
12
Runners must be
pushed up against
the drawer front
DL
x 2
F
F
F
DL
11
N c
F
12
DR
N d
8
Assembly Instructions
Step 15
Prepare the left side
a: Fit 6 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
I
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
N a
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
1
. .
B
1
A
N a
1
I
F
Use the Main Fittings Bag for Steps 15 - end
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
1st
F
I
screw
Finished
front edge
I
I
I
CL
N a
1
CL
I
N a
I
I
N a
CL
I
CL
I
N a
I
I
I
CL
I
N a
I
I
CL
I
N a
front edge
Finished
a:
front edge
Finished
CL
I
I
I
N a
Tap 2 wooden dowels
into the left side .
1
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
H
b:
Finished
front edge
F
F
CL
CL
1
F
F
CL
CL
Finished
front edge
CL
CL
CL
c:
CL
F
F
CL
CL
A
B
B
A
H
B
CL
CL
H
A
10mm
H
1
9
Assembly Instructions
Step 16
Prepare the right side
a: Fit 6 CR runners
to the right side .
The 1st screw uses
N b
2
I
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
I
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
F
the hole at the top of the
runner .
N b
c: Insert 2 large locking
cam nuts into the
right side .
B
2
a:
1st
screw
I
front edge
Finished
N b
CR
I
I
CR
N b
I
I
I
CR
N b
N b
Finished
front edge
I
I
I
CR
N b
I
I
I
CR
N b
I
I
I
2
I
I
CR
I
I
CR
N b
F
front edge
Finished
Push 2 of the quickfit
dowels as far as they
A
will go into the right side
. .
2
Tap 2 wooden dowels
into the right side .
H
2
b:
c:
F
F
F
F
F
F
CR
CR
CR
CR
CR
CR
Finished
front edge
2
A
B
A
H
B
CR
CR
CR
CR
CR
CR
Finished
front edge
B
H
A
2
10
Assembly Instructions
Step 17
Prepare the cross rail
Tap 4 wooden dowels
into the cross rail .
H
6
Step 18
Fit the cross rail onto
the left side
Push the cross rail
down onto the left side
. .
1
6
H
H
Finished
front edge
Finished
front edge
6
CL
Finished
front edge
CL
Note: The cross rail has no
holes drilled on either surface
6
H
H
CL
CL
CL
CL
1
Step 19
Prepare the plinth
Insert 2 large locking
cam nuts into the
plinth .
Push 2 of the quickfit
dowels as far as they
will go into the plinth .
Tap 2 wooden dowels
into the plinth .
11
B
5
A
5
B
A
H
5
H
A
B
B
5
A
H
Assembly Instructions
Step 20
Fit the plinth
Push the plinth down
onto the left side .
5
1
Turn the large locking
cam nut clockwise to
B
the “2 o’clock” position
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 21
Prepare the 2 back
rails
Carcase Assembly
hps://www.youtube.com/watch?v=9C7tgv5xnbE
5
CL
CL
CL
CL
A
B
1
CL
CL
B
Edge Edge
Turn to “2 o’clock”
Edge
Insert 2 large locking
cam nuts into each of
the back rails .
B
7
Push 2 of the quickfit
dowels as far as they
A
will go into each of the
back rails .
Tap 2 wooden dowels
7
H
into each of the back
rails .
7
Step 22
Fit 1 of the back rails
Push a back rail
down onto the left side
1
. .
Turn the large locking
cam nut clockwise to
B
the “2 o’clock” position
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
7
B
A
H
x 2
B
7
A
H
7
CL
CL
CL
CL
CL
CL
1
12
Assembly Instructions
Step 23
Fit the other back rail
Push the back rail
7
down onto the left side
1
. .
Turn the large locking
cam nut clockwise to
B
the “2 o’clock” position
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
CL
CL
7
CL
CL
CL
CL
1
Step 24
Fit the right side
Push the right side
down onto the assembly.
Turn the 3 large locking
cam nuts clockwise
B
to the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Carefully stand the
unit up for the next
step.
Warning: The
unit is heavy.
Lift with care.
2
Finished
front edge
2
CL
CL
CL
CL
CL
CL
13
Assembly Instructions
Step 25
Prepare the divider
a: Fit a runner to
the divider .
The 1st screw uses
N a
4
I
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
I
. use the holes that line
up with the other panel
holes.
Finished
front edge
a:
Finished
front edge
b:
I
I
CL
N a
4
F
4
1st
front edge
Finished
I
front edge
Finished
I
screw
N a
CL
F
b: Fit a screw into
F
the 2nd hole in at the top
of the runner .
N a
c: Insert 2 large locking
cam nuts into the
divider .
Push 2 of the quickfit
dowels as far as they
will go into the divider
. .
4
Tap 2 wooden dowels
into the divider .
Turn the divider over
d: Fit a runner to
the divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
I
. use the holes that line
up with the other panel
holes.
e: Fit a screw into
the 2nd hole in at the top
of the runner .
B
4
A
H
4
N b
4
I
F
N b
Finished
front edge
c:
d:
e:
B
A
CL
4
H
H
B
A
Turn the divider over
I
I
I
4
CR
N b
Finished
front edge
F
CR
4
Finished
front edge
CR
N b
1st
screw
F
I
front edge
Finished
front edge
Finished
14
Assembly Instructions
Step 26
Fit the divider to the
top
Push the divider
down onto the top .
Turn the 2 large locking
cam nuts clockwise
B
to the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
4
3
3
4
Finished
front edge
Step 27
Fit the top
Push the top down
onto the assembly.
Turn the 4 large locking
cam nuts clockwise
to the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Carefully lay the unit
down onto its front
edges for the next
step.
3
B
3
CR
CR
CR
CR
CR
CR
CR
Finished
front edge
15
Warning: The
unit is heavy.
Lift with care.
Assembly Instructions
Step 28
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
K
outside edges of the
17
back .
Note: Nails should be
spaced out evenly.
17
Squaring up a Chest and tting the Back Panel
www.youtube.com/watch?v=FeaI6541z7o
The measurement from top corner X to bottom corner X must be
a:
equal to the measurement from top corner Y to bottom corner Y
b:
x
x
K
17
Cut-out
y
CR
CR
y
y
Step 29
Fit the 5 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. and 1 plastic nail into
2
plinth .
Carefully stand the
unit up for the next
step.
5
Warning: The
unit is heavy.
Lift with care.
J
1
xx
J
J
2
CR
CR
5
J
J
1
J
16
Assembly Instructions
Step 30
Fit the overbalance
protector kit
a: Before fitting the
overbalance protector
kit, use a spirit level to
check the top of the unit
is level, front-to-back
and side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting of
the overbalance
protector kit to the
unit, or an alternative
fixing method of your
choice.
O
WARNING!
In order to prevent overturning
this product must be used with the
wall attachment device provided
a:
CR
CR
CR
Wall fixings are not
supplied as they will
need to suit the wall
type.
Take care when
Note:
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
CR
CR
CR
CR
in back panel
b:
Top
O
Back
Cut-out
17
Assembly Instructions
Step 31
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Assembly is complete
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
CR
CR
CR
CR
CR
CR
CR
Side
panel
Drawer
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
18
ALR3296
Loading...