Nest of Tables
Assembly Instructions - Please keep for future reference
052 xx 3040
412 / 7886
427 / 2535
609 / 5992
Dimensions
Width - 29.6cm
Depth - 29.0cm
Height - 34.4cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev C - 05/05/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
Larger Nest
8792
Top (42.2x35cm)
Smaller Nest
8791
Top (29.0x29.6cm)
8794
8768
Right End
(32.2x34.4cm)
Right End
(28.4x29cm)
8793
8767
Left End
(32.2 x 34.4cm)
Left End
(28.4x29cm)
6013
8769
(31.6x19cm)
Rail
Rail
(25.6 x 19cm)
2
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 01709 534123
for important information when contacting Customer Helpline.
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
A
Large cam x 16
Code 760001103
B
Metal dowel x 16
Code 760003004
C
Knock-in Trim x2
Code 684xx3040
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
40
50
60
70
80
90
100
3
0
mm
10
20
30
110
120
130
140
150
Drill
160
170
Exploded View
8792
6013
8793
8767
8794
8791
8769
8768
4
Assembly Instructions
Step 1
Fitting cams & dowels
to end panels.
A
Note: Ensure cam
arrow points towards
the edge with hole.
B
Note: Insert metal
dowels ‘B’ as far as
shown by arrows.
Do not over tighten.
Fittings you will need for this step:
B
x8
A
A
A
x8
B
B
8793
A
8794
B
B
A
B
B
A
A
A
A
8767
8768
B
B
Step 2
Fitting cams & dowels
to top panels.
B
Note: Insert metal
dowels ‘B’ as far as
shown by arrows.
Do not over tighten.
Step 3
Fitting cams to rails.
A
Fittings you will need for this step:
B
x8
B
B
8792
B
Fittings you will need for this step:
A
x8
A
A
6013
A
A
B
B
B
B
8791
B
A
A
A
A
8769
Note: Ensure cam
arrow points towards
the edge with hole.
5
Assembly Instructions
Step 4
Attach end panels to
the back rails.
Insert dowels in the end
panels into the cams
(already inserted) in the
back rails.
8794
Cams to inside
Dia. A
A
Turn cam 180 degrees
to lock
Please ensure that tops
of back rails are level
with tops of end panels
(see dia. A).
6013
8793
8768
Cams to inside
8769
8767
Step 5
Attach tops to end
panels.
Insert dowels in the Top
panels into the cams
(already inserted) in the
End Panels.
Please ensure that back
of tops are level with back
of end panels.
Turn cam 180 degrees
to lock.
8767
8791
8768
8792
8793
8794
6
Assembly Instructions
Step 6
Attach trim
lay unit on its back.
Locate the notch on
the trim into the grooves
in the end panels.
Ensure the trims are
positioned correctly.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and trims to protect the
trims.
Ensure that the trims
are inserted fully.
Peel off protective film
from each Trim.
C
C
8793
8794
7
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
(by contacting the customer service line your statutor y rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
8
Notes
Notes
Loading...