Nest of Tables
Assembly Instructions - Please keep for future reference
052 xx 6000
483/6524
Dimensions
Width - 47cm
Depth - 38.8cm
Height - 40cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev A - 28/09/2015
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 4.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
Grooved
edge
Large left end panel (38.4x36cm)
Code -
Large top
Code -
6858
(47x38.8cm)
6857
Large trim x 2
(38.4cm long)
Code -
684006520
Grooved
edge
Large right end panel (38.4x36cm)
Code -
6859
Large rail x 1
Code -
6860
(39.8x16cm)
Mid left end panel (33x30.2cm)
Code -
0032
Mid rail x 1 (30.6x16cm)
Code -
Small top
Code -
0034
(29.6x27.2cm)
0035
Mid top
Code -
(36x33cm)
0031
Small left end panel (27.6x24.4cm)
Code -
0036
Small rail x 1 (24.2x16cm)
Code -
0038
Mid right end panel (33x30.2cm)
Code -
0033
Small right end panel (27.6x24.4cm)
Code -
0037
2
Components - Exploded View
Important - Thick lines indicate finished edges
6857
684006520
Trim
6858
6860
0036
0035
6859
6854
0031
0034
0032
684006520
Trim
0033
0038
0037
3
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
A
Large cam x 24 - Code 760001103
B
Metal dowel x 24 - Code 760003004
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
0
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
4
Assembly Instructions
Step 1
Fitting dowels to tops
B
Note: Insert metal
dowels as far as
B
shown by arrows.
Do not over tighten.
Step 2
Fitting cams to rails
A
Note: Ensure cam
arrow points towards
the edge with hole.
B
x12
A
x12
B
B
B
B
B
B
B
0031
6857
B
B
B
B
B
0035
A
A
A
A
6860
A
A
0034
A
A
A
A
A
A
0038
Step 3
Fitting cams and
dowels to end panels.
A
Note: Ensure cam
arrow points towards
the edge with hole.
B
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
A
x12
B
x12
Front grooved edge
B
B
A
0037
A
6859
A
0033
B
B
B
B
B
B
A
B
B
A
B
B
6858
A
0032
A
0036
A
A
A
A
A
5
Assembly Instructions
Step 4
Assembly of large
table
Front grooved edge
Front grooved edge
Insert dowels in left
and right
6858
end panels into cams
in rail then lock.
6860
Now insert dowels in
6857
top into cams
6858
in left and right
end panels then
6859
B
6859
A
B
A
lock.
A
Turn cam 180 degrees
to lock
Step 5
6857
6858
6860
6859
Ensure backrail
sits flush.
Assembly of mid &
small table.
Mid table.
Insert dowels in left
and right
0032
B
0033
end panels into cams
in rail then lock.
0034
Now insert dowels in
0031
top into cams
0032
in left and right
end panels then
0033
B
A
lock.
Turn cam 180 degrees
to lock
Small table.
Insert dowels in left
and right
0036
B
0037
end panels into cams
in rail then lock.
0038
Now insert dowels in
0035
top into cams
0036
in left and right
end panels then
0037
B
A
lock.
Turn cam 180 degrees
to lock
0031
A
0033
Ensure backrail
sits flush.
0034
0032
Mid table.
0035
0037
A
0038
Small table.
0036
6
Assembly Instructions
Step 6
Attach silver trim
Remove protective film
from silver trim.
Warning:
Lift with care.
Locate the notch on
silver trim into
groove on ends
6859
and .
Ensure the silver
trims are positioned
correctly (DIAG 1).
To insert silver trims
use a hammer, place a
cardboard packing piece
between the hammer
and silver trims to
protect the silver
trims (DIAG 1).
6858
Fittings you will need for this step:
Large silver trims
(x2)
6859
6858
DIAG 1
Cardboard
packing piece
DIAG 2
Ensure silver trims
are inserted fully
(DIAG 2).
Congratulations!
Your unit is complete.
6858
6859
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Simply contact us on CUSTOMER HELPLINE : 01709 534123 Between 8am - 4.30pm
Monday to Thursday and 8am - 2.30p.m friday. Your statutory rights are not affected.
Please have the following information: Unit Description, Product Code, Product Colour,
Place of Purchase, Catalogue Ref. No., Item Code, and have the assembly instructions close
to hand.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
You can also e-mail your requests to us at: customer.helpdesk@addspacefl.co.uk
Alternatively Write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
7
Loading...