Ultimate Storage Bed
Assembly Instructions - Please keep for future reference
501-3298
Dimensions
Width - 143,5cm
Depth - 196cm
Height - 91,5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Issue 2 - 24/09/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
.
Check you have all the
components and tools listed on
pages 2 and 3.
.
Remove all fittings from the
plastic bags and separate them
into their groups.
.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
.
Make sure you have enough
space to layout the parts before
starting.
.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Do not stand or put weight on
the product, this could cause
damage.
.
Assemble the item as close
to its final position (in the same
room) as possible.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
.
Parts of the assembly will be
easier with 2 people.
.
Dispose of all packaging
carefully and responsibly.
.
We do not
care and maintenance
.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
1
.
From time to time check
that there are no loose
screws on this unit.
.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
20
21
Left side panel x 2 (36,2 x 30,4cm)
13
22
Large middle bar x 2 (77 x 6,5cm)
Side bar x 8 (36,9 x 4,5cm)
Drawer front x 4 (76,4 x 16,1cm)
Middle left side panel x 2 (36,2 x 40cm)
14
Middle right side panel x 2 (36,2 x 40cm)
15
Right side panel x 2 (36,2 x 30,4cm)
16
Drawer right side x 4 (35 x 11cm)
23
Drawer left side x 4 (35 x 11cm)
24
Drawer back x 4 (73,3 x 11cm)
25
Drawer base x 4 (74,4 x 34,9cm)
26
Base x 4 (36,9 x 30,1cm)
17
Shelf x 4 (36,9 x 30,1cm)
18
Small middle bar x 6 (77 x 4,5cm)
19
Back panel x 2 (79,8 x 36cm)
27
Small back panel x 4 (38,2 x 36cm)
28
Runners x 8 (27,4 x 1,6cm)
43
2
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 03456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
J
7 x 40mm Bolt X 48
L
8 x 8
Nail X 70
Tools required
K
3,5 x 30mm Screw X 32
M
8,0 x 15mm Small wooden dowels X 16
Phillips screwdriver
(medium & large)
F
8,0 x 30mm Wooden dowels X 64
O
3,0 x 14mm Screw X 24
2 m
Ruler/tape
measure
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Eye protection
(when using a
hammer or glue)
Assembly Instructions
Step 1
Step 1
Step 1
It takes 3 hours to build
the bed.
Insert wooden dowels
into the indicated parts.
F
F
F
F
F
6X
19
F
F
4X
18
F
4X
24
8X
21
F
23
20
4X
2X
F
F
F
F
F
F
Step 2
Insert small wooden
dowels where shown
Attach runners to the
middle panels and
using screw .
M
43
14
O
15
Step 3
14
19
15
Fix 3 middle bars to the
middle panels and
using bolts .
J
2X
2X
O
O
43
43
J
O
M
14
O
O
M
O
M
M
J
O
M
19
O
O
M
O
M
43
O
O
43
M
15
Important:
Make sure panels
are positioned as
shown.
14
IS
H
T
E
P
U
ID
S
THIS
SIDE
UP
J
19
J
19
J
15
J
4
Assembly Instructions
Step 4
Attach base ,shelf ,
17
and 2 side bars to right
side panel using bolts
J
.
16
Step 5
Step 4
Attach base ,shelf ,
17
and 2 side bars to left
side panel using bolts
J
.
13
18
21
18
21
2X
2X
17
21
21
J
18
17
18
J
J
16
J
21
J
Step 5
Step 6
Step 4
Attach the two parts from
step 4 and 5 to the
previously assembled
cabinet using bolts .
J
2X
13
13
J
J
J
J
J
P
E
U
IS
SID
H
T
J
J
J
J
21
J
J
16
5
Assembly Instructions
Step 7
Step 7
2X
Fix large middle bar
using screws .
J
Step 7
Step 8
Step 8
20
2X
P
E
U
ID
IS
S
H
T
J
20
J
Turn cabinet up side down
and fix back panels and
using nails .
28
27
L
L
L
L
L
28
L
L
L
L
L
27
P
E
U
IS
H
SID
T
L
L
L
L
28
L
L
L
6
Assembly Instructions
Step 7
Step 9
Step 9
a: Attach drawers sides
23
and to drawer front
using screws .
22
24
K
4X
24
K
26
b: Slide drawer base
into groove.
c: Attach back using
screws .
K
25
26
23
22
K
K
25
K
K
K
K
Step 10
Slide drawer into cabinet.
Assemble is complete!
2X
T
H
IS
SID
E
U
P
7
Loading...