4 Cube Storage Unit
Assembly Instructions - Please keep for future reference
011 xx 3555
385 / 0886
426 / 9706
404 / 5982
122 / 7954
109 / 7232
116 / 5140
Dimensions
Width - 61.2cm
Depth - 29.5cm
Height - 61.2cm
GREAT BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967
Please turn to back page for important information when contacting Customer Helpline.
01709 534123
Rev B - 01/107/2013
MADE IN
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
9096
9097
Top / Bottom x2 (58.0x29.3cm)
Shelf (58.0x29.3cm)
9103
9101
End Panel x2
Back Panel x2 (30.8x29.5cm)
(61.2 x 29.5cm)
9098
Divider x2 (28.2x29.1cm)
2
If you have damaged or missing components, call the
Components - Fittings
Customer Helpline: 0845 0613967
for important information when contacting Customer Helpline.
01709 534123
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
A
D
G H
45mm screw x 8
Code 690001075
L bracket x 1
Code 760001901
Panel Pin Locator
Code 684004501
B
E
Dowel 30mm x 8
Code 770001006
12mm screw x 2
Code 690001099
Cover cap x 8
C
F
Dowel 50mm x 2
Code 770003550
Panel pin x 16
Code 760001012
Tools required
Large Cross
Headed
Screwdriver
Small Hammer
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
mm
10
0
20
30
3
40
50
60
70
80
90
100
110
120
130
140
150
160
170
Exploded View
9103
9096
9101
9098
9098
9096
9097
9103
9101
4
Assembly Instructions
Step 1
Fitting dowels to the
divider panel.
Insert 2 of the 30mm
dowels into the pre-
B
drilled holes in one end of
the divider panel
and 2 50mm dowels
9098
C
into the pre-drilled holes
in the other end of the
same panel.
Insert 2 of the 30mm
dowels into only one
B
end of the other divider
panel .
9098
Step 2
Fitting dowels to the
shelf panel.
B
x4
x4
C
x2
9098
B
B
B
30mm
50mm30mm
C
C
B
B
9098
B
B
Insert 2 of the 30mm
dowels into the pre-
B
drilled holes in both ends
of the shelf panel .
9097
Step 3
Connect divider panel
and divider panels.
Locate the divider panel
which has the 2
9098
50mm dowels inserted
into the pre-drilled holes.
Slide the 50mm dowels
C
through the predrilled holes in the shelf
panel and connect
9097
to the remaining divider
panel .
9098
C
9097
B
B
9098
9097
9098
9098
9097
9098
5
FINISHED EDGES TO THE FLOOR
Assembly Instructions
Step 4
Connect top/bottom
panels to the dividers
panels.
Insert the dowels (already
inserted in the divider
panels) into the predrilled holes in the top/
bottom panel .
9098
9096
9096
9098
9098
9096
Step 5
Fasten one of the end
panels to the shelf and
top/bottom panels.
Connect the end panel
9103
to the dowels in
the shelf panel
(already inserted).
Secure the end panel
in place by using
9103
screws and screwing
into the pre-drilled holes
in the top/bottom panels
.
9096
A
9097
A
x4
9096
A
9103
A
9097
9096
A
A
6
Assembly Instructions
Step 6
Fasten the other end
panel to the shelf and
top/bottom panels.
Connect the end panel
9103
to the dowels in
the shelf panel
(already inserted).
Secure the end panel
in place by using
9103
screws and screwing
into the pre-drilled holes
in the top/bottom panels
.
9096
A
9097
A
x4
9096
A
9097
9103
A
A
9096
Step 7
IMPORTANT!
Squaring the unit up.
Ensure a tape
m measure is used
to squure unit up!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
YY
YY
XX
YY
XX
XX
XX
YY
YY
XX
DIAG 1
XX
7
YY
XX
DIAG 2
YY
XX
DIAG 3
YY
Assembly Instructions
Step 8
Attach the 2 back
panels.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
Ensure that you measure
the backpanel and
attach the longest
side as shown.
Ensure that the distance
from the edge of the back
panels to the edge of the
top / bottom / end panels
is equal on every back
panel.
F
x16
G
x1
Plain chipboard surface
F
F
G
9101
9101
30.8cm
29.5cm
Stand the unit upright.
Step 9
Fixing to wall
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
D
x1
E
x2
Warning:
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools. If in
doubt consult a qualified
person.
8
Assembly Instructions
Step 8
Use the cover caps
to conseal exposed
fittings.
Using the 8 cover caps
H
provided, conceal the
exposed screws by
placing these caps over
them.
H
x8
H
H
H
H
9
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
0845 061 3967
(by contacting the customer service line your statutory rights are not aected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspace.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
Notes
Loading...