Page 1
Josie - Bunkbed Drawers
Assembly Instructions - Please keep for future reference
498/9141
471/7801
Dimensions
Width - 59.6cm
Depth - 93.0cm
Height - 20.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, c a l l t h e Customer Helpline: 03456 400 800
Issue 1 - 01/10/15
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
We do not
recommend the
use of power
drill/driversfor
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note:If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
Please check you have all the panels listed below
2
3
1
Drawer front x 2 (
Drawer back x 2 (
93.0 x 20.5cm)
91.0 x 13.7cm)
Left drawer side x 2 (
55.7 x 13.7cm)
5
4
6
Right drawer side x 2 (
Cross bar x 4 (
Drawer base x 6 (
55.7 x 6.5cm)
57.5 x 26.5cm)
55.7 x 13.7cm)
2
Page 4
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 03456 400 800
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly.
In some cases more fittings may be supplied than are required.
A
Wooden dowel x 28
10 x 40mm
D
7 x 50mm Bolt x 4
Cab. 17
F
Wheel Rd20 x 8
B
Metal dowel x 8
E
Allen key x 1
C
Locking nut x 8
G
3.5 x 16mm Screw x 16
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
3
Page 5
Assembly Instructions
Step1
Insert wooden dowels
into the indicated parts.
A
A
A
Step2
4
A
A
2x 2x
A
A
3
A
A
5
4x
A
A
Screw metal dowels into
drawer front .
1
B
B
B
B
B
1
B
B
2x
4
Page 6
Assembly Instructions
Step3
Assembling drawer sides.
3
Fit left drawer side and
right drawer side to
drawer front .
Insert 2 locking nuts into
each drawer side as shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
1
C
3
4
3
2x
1
1
4
C
C
C
C
C
C
Step4
Fit cross bars to drawer
front.
5
5
5
5
2x
Page 7
Assembly Instructions
Step5
Slide drawer bases into
the grooves of drawer sides
and cross bars.
6
6
6
6
2x
Step6
With help, place drawer
back properly ensuring
2
dowels in drawer sides and
cross bars are all fit into
the holes.
Then, fix drawer back using
bolts and allen key .
D
E
D
E
D
2
2x
6
Page 8
Assembly Instructions
Step7
Attaching wheels
Carefully turn the product
upside down.
Fix wheels F using screws .
Leave 6cm distance from the
drawer front and drawer back
as shown.
F
G
G
G
F
G
G
F
6.0cm
F
2x
F
G
F
G
G
G
F
6.0cm
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
7
Loading...