Argos 4986034 ASSEMBLY INSTRUCTIONS

Cabin bed - White
Assembly Instructions - Please keep for future reference
1478538
Dimensions
Length - 195cm Depth - 96cm Height - 71cm Weight - 20kg
Important – Please read these instructions fully before starting assembly
Issue 1 - 05/10/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
80-10104-20 deb nibaC
IMPORTANT! KEEP FOR FUTURE REFERENCE
PLEASE DISPOSE OF PACKAGING MATERIAL.
PLASTIC BAGS CAN BE DANGEROUS TO YOUNG CHILDREN
WARNING! Not suitable for children under 4 years.
WARNING! Do not place this child’s bed near heat sources, windows and other furniture.
WARNING! Do not use this child’s bed if any of the parts are broken, torn or missing.
WARNING! Once assembled, this bed must not be disassembled. Screws must not be removed once inserted.
This child’s bed is to be used with a 1900mm x 900mm ma ress.
Suitable for children over 4 years to adults.
All assembly Įxings should be checked periodically and re-
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not
be placed too close to other furniture or windows, bl
placed either
Any addi
ght to any wall or have a gap of 300mm between the wall and the side of the bed.
onal or replacement parts should only be obtained from the manufacturer or distributor.
This product complies to standard BS8509: 2008+A1:2011
ind cords, curtain pulls or other strings or cords, and should be
ghtened where necessary.
CARE AND MAINTENANCE
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.
1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fi ttings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its fi nal position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your fl oor.
• Parts of the assembly will be easier with 2 people.
• From time to time check that there are no loose screws on this unit.
• We do not recommend the use of power drill/drivers for inserting screws,
as this could damage the unit. Only use hand screwdrivers.
• Dispose of all packaging carefully and responsibly.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
2
If you have damaged or missing components,
Components - Parts
call the Customer Helpline:
Please check you have all the parts listed below
0045 7668 8055
Leg x4 (71.7x4.3x4.3cm)
1
No. 12-04307172-20
Slat x14
4
No. 12-01508971
(89.7x6.5x1.47cm)
Endrail curved x2
2
(87.7x9.2x2.0cm)
No. 12-02008771-20
T&G panel x2
5
(58.5x8.7x0.8cm)
No. 12-00805852-20
Endrail x2
3
(87.7x6.5x2.0cm)
No. 12-02008772-20
T&G panel x16
6
(58.5x9.4x0.8cm) No. 12-00805851-20
T&G panel x2
7
(58.5x8.1x0.8cm)
No. 12-00805853-20 No. 1305-18673-20
Bedside x2
8
(186.7x8.9x2.0cm)
3
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings may be supplied than are required.
No. 3913-06090
A
M6x90mm Connecting bolt x4
No. 3930-10045
D
10x45mm Dowel x8
No. 3922-06014
B
M6 ø10x14mm Barrel nut x4
No. 3909-63090
E
6,3x90mm Assembly screw x16
No. 3901-40030
C
4,0x30mm Chipboard screw x28
Tools required
Phillips screwdriver (medium)
Flatblade screwdriver (medium)
Allen key 4mm incl.
No. 4033-004
Small hammer
Ruler/tape measure
Eye protection (when using a hammer or glue)
4
Assembly Instructions
Step 1
Attach the dowels D to
8
bedsides
.
It may be necessary to tap the dowels in very gently with a small hammer.
Step 2
2
Attach endrails
3
to leg 1 with screws
E
using the allen key.
and
Repeat same procedure for second headboard
Step 3
D
E
1
E
E
3
D
8
x2
D
2
UP
DOWN
410 307
7
2
and
Slide T&G panel between endrails
3
.
Followed by 8 T&G panel
6
and fi nish with 1 T&G
5
panel Attach leg
2
and 3 with screws
E
using the allen key.
.
1
to endrails
Repeat same procedure for second headboard
2
7
1
E
7
Important note: A variation of the width of the panels of ±2-3% has to be expected as wood is a live material, i.e. variation of 2-3 cm per 1 meter. Leaving some space at the panels, tongue & groove, should be distributed regularly along the bed end. If there is too little space for the panels, these should be acclimatized for 2-5 days in order to adapt to the humidity of the room. The reason for this problem might be that the wood has absorbed a little
moisture during transportation/stocking.
6
6
6
6
6
6
6
6
3
6
6 6
6
5
1
5
E
E
5
Assembly Instructions
Step 4
Attach bedsides 8 to
1
the legs the barrel nuts the small holes in the bedsides connecting bolts through the legs meet the barrel nuts
Then fasten with the allen key.
by pushing
B
into
8
. Push
A
1
to
A
B
B
.
1
A
8
8
B
B
8
1
B
A
Step 5
Repeat same procedure as described in “Step 4”
A
A
B
8
8
1
A
B
B
8
B
1
6
Assembly Instructions
Step 6
Place one slat 4 in the centre of the bed. Follow the measurement .
4
Place two slats ends of the bed. Follow the measurement .
Push the bedsides together whilst attaching middle slat
4
bed with two chipboard
C
screws
.
in the
to the
C
8
15 mm
4
PUSH
C
8
843 mm
C
4
4
Step 7
Position the remaining
4
eleven slats bed with a distance of 73 mm between each.
Fasten each slat with two screws
C
Assembly is complete.
in the
8
C
4
73 mm
4
4 4 4
PUSH
C
4 4 4 4 4 4
C
C
If you need help or have damaged or missing parts,
call the Customer Helpline: 0045 7668 8055
E-mail: order@fl exa.dk Ref.no. 44-01139-20 D Stand: 051015 Page 8 (80-10104-20)
7
C
Loading...