Sit N’ Sleep Bed
Assembly Instructions - Please keep for future reference
758/5418
758/5401
IMPORTANT NOTE:
The top surface of the
mattress should not come
above this line.
Dimensions
Width - 200cm
Depth - 99/143cm
Height - 170.5cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
- Please read these instructions fully before starting assembly
Issue 1 - 08/11/13
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Because of the size of this unit,
it is recommended to assemble it
in the room intended for use.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
Warnings
• READ CAREFULLY - RETAIN
FOR FUTURE REFERENCE
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
• Always use the ladder for
entering and leaving the upper
bunk.
• The recommended mattress
size is L1900 x W910 mm.
• Ensure thickness of mattress
does not exceed 220 mm.
• Refrain from using the bunk
bed if any structural part is
broken or missing.
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• At least 2 people are required
to assemble this product.
• Unit weight: 38.6kgs.
• Retain Assembly Instructions
for future reference.
• Please advise your children to
only enter and leave the upper
bunk by using the ladder.
• Please prohibit more that one
person on the upper bunk.
• Please prohibit children from
jumping on the upper and lower
beds.
• WARNING: Do not allow
children under 6 years of age to
use the upper bunk due to risk
of injury and falls.
• STRANGULATION HAZARD -
Never attach or hang items such
as ropes, strings, cords,
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
harnesses and belts to any part
of the bunk bed.
• WARNING: Children can
become trapped between the
bed and the wall. To avoid risk
of serious injury the distance
between the top safety barrier
and the wall shall not exceed 75
mm or shall be more than 230
mm.
• THIS BED COMPLIES WITH
EN747-1:2012 / EN747-2:2012
Care and maintenance
• Please clean the unit surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
1
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Parts
Please check you have all the parts listed below
Sticker “4”Sticker “3”Sticker “2”Sticker “1”
1 Back right-hand
Front right-hand
endpost
(Ø5 x 170.5cm)
5
Upper side safety rail x 2
(91 x 36 x 4cm)
Lower rail
8
(190 x 6.5 x 2.5cm)
2
end post
(Ø5 x 170.5cm)
6
Lower side rail x 2
(91 x 4 x 2cm)
3
end post
(Ø5 x 170.5cm)
7
9
Upper back safety rail
(190 x 41.5 x 2.5cm)
4Back left-hand
Front left-hand
end post
(Ø5 x 170.5cm)
Middle side rail x 2
(89 x 2 x 2cm)
10
Upper front safety rail
(190 x 41.5 x 2.5cm)
Slats (with webbing attached) x 24
11
(94 x 2.5 x 2.6cm)
2
Components - Parts (cont.)
Please check you have all the parts listed below
Sticker “12” Sticker “13”
Left ladder side rail
12 Right ladder side rail
(Ø2.5 x 141cm)
15 Shelf side frame x 2
Ladder brace
(45.5 x 1.5 x Ø1cm)
13 Ladder step x 4
(Ø2.5 x 141cm)
16 Shelf brace x 4
(52 x 33 x 1.6cm)
14
(Ø2.5 x 29 cm)
17
(Ø1.3 x 72cm)
Small shelf panel
18 Big shelf panel
(72 x 24 x 1.2cm)
19 Back brace x 2
(72 x 33 x 1.2cm)
3
20
(135.5 x 2 x Ø1.3cm)
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
M6 x 80mm Bolt x 11
D
M6 x 27mm Bolt x 12
G
Big screw x 8
J
M6 Curved washer x 19
M
M6 Lock nut x 6
P
B
M6 x 50mm Bolt x 8
E
M6 x 20mm Bolt x 11
H
Small screw x 2
K
Plastic washer x 8
N
Spring washer x 8
Q
C
M6 x 35mm Bolt x 2
F
M8 x 60 mm Bolt x 12
I
M8 Curved washer x 12
L
Wall strap x 1
O
Plastic cap x 8
Spanner x 1
Allen key x 1
Tools required
Crosshead screwdriver
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
4
Assembly Instructions
Step 1
Assembling end panels
Lay all parts flat on a soft
surface on the floor to
avoid damaging any of
the parts.
Note:
Identify and
correctly position
end posts , ,
3 4
and by
1 2
looking for the
sticker label
pasted on the
posts.
Note:
Determine your
preferred shelf
position. Then
attach the middle
side rails
7
either on the left
or right.
a: b:
A J
Sticker “2” Sticker “1”
2
A J
6
2
RIGHT-HAND END PANEL
E
E
5
6
E
E
E
2
5
1
AJ
a: Attach the lower side
rail to end posts
2
and then secure
using washers and
A
bolts .
Note: Do not fully
tighten bolts at
this stage.
16
J
b: Attach the upper side
safety rail into position
and secure using bolts .
Repeat above steps to
assemble the left-hand
end panel as shown in
the diagram.
5
E
Note: Fully
tighten all bolts
using allen key .
Q
LEFT-HAND END PANEL
Sticker “4”
A J AJ
A J AJ
A J AJ
E
E
5
7
7
6
E
E
Sticker “3”
34
5
Assembly Instructions
Step 2
Attaching rails
Note: Determine
your preferred
bunk bed entry
position. Then
attach the front
safety rail with
10
the entry space
positioned either
on the left or right.
a: Identify the correct
rails for assembly and
with the help of an
assistant attach the lower
tubes of upper back
safety rail , upper front
safety rail and lower
8
rail to end posts using
bolts , washers and
nuts .
9
10
F
M
I
Note:
Do not fix bolts on
lower holes of
back safety rail
at this stage.
Locate hole on
centre of lower
8
rail and make
sure to position it
up.
9
I
F
F
J
A
I
F
3
I
F
M
I
F
4
I
I
F
I
F
4
b:
J
10
M
M
8
A
3
9
10
hole up
c:a:
9
O
A
J
F
I
O
O
2
O
O
F
I
F
I
M
1
O
A
J
F
I
F
I
M
O
O
1
O
O
Do not fully
tighten bolts at
this stage.
b: Attach the top tubes
of upper back safety rail
9
and upper front safety
10
rail to end posts using
bolts and washers .
Note: Do not fully
tighten bolts at
this stage.
c: Insert plastic caps
into holes on the right
end posts & and fix
by pushing firmly as
shown.
1 2
JA
O
Option for
right upper bunk entry
10 10
3
4
Option for
right shelf position
2
1
3
Option for
left upper bunk entry
2
1
4
Option for
left shelf position
6
Assembly Instructions
Step 3
Attaching back braces
a: Position the back
braces as shown and
attach it to upper back
safety rail using bolts
F
, washers and nuts .
b: Attach the back
braces to lower rail
using bolt as shown.
20
9
I
20 8
E
Note: After all
bolts in step 2
and 3 are
positioned, fully
tighten all bolts
and nuts using
allen key and
spanner .
Q
P
M
I
F
M
3
20
9
20
E
8
M
F
I
2
Step 4
Assembling shelf
a: Attach the shelf
braces to shelf side
frames using bolts
as shown.
b: Position the shelf
panels and as
shown and attach it to
shelf braces using
screws . Tighten screws
using a crosshead
screwdriver.
17
16
D
Note: Do not fully
tighten bolts at
this stage.
18 19
17
G
a: b:
9
M
20
3
F
I
20
E
20
8
a:
16
D
D
D
17
D
17
16
17
D
17
D
D
D
b:
17
16
D
18
Note: After all
bolts and screws
are positioned,
fully tighten all
G
18
G
17
G
17
G
G
17
bolts using allen
Q
key .
G
17
G
G
19
17
G
7
Assembly Instructions
Step 5
Attaching shelf
Position the shelf on the
bed as shown and attach
the side frames to
middle right side rails
using bolts . Tighten
bolts using allen key .
16
7
D
Q
D
D
7
D
16
7
D
16
Step 6
Attaching slats
a: With the help of an
assistant, line up the
11
slats onto upper rails
9 10
and . Push firmly
down to lock it into
position. Check that they
cannot be removed by
slightly pulling upwards.
b: Extend the end of the
webbing on the slats
and secure to bottom
edge of side safety rails
5
using screws .
Tighten screws using a
crosshead screwdriver.
11
H
D
9
5
H
11
10
5
H
16
7
a: b:
11
10
11
5
H
8
Assembly Instructions
Step 7
Assembling ladder
Referring to diagram,
attach the ladder steps
to ladder side rails
13
and using bolts ,
spring washers ,
curved washers and
plastic washers .
12
B
N
J
K
Tighten all bolts using
allen key .
Q
Note: Identify and
correctly position
the ladder side
12
rails and
13
by looking for the
sticker labels
pasted on the
rails.
14
Sticker “12”
B
Sticker “13”
N
J
K
J
N
12
K
J
N
B
J
N
B
B
K
14
14
K
14
K
J
N
B
13
N
J
K
14
B
N
J
K
B
N
J
K
B
12
N
B
J
14
K
Step 8
Attaching ladder
Attach the ladder to the
upper front safety rail
using bolts as shown.
C
Tighten bolts using allen
Q
key .
10
10
12
C
13
C
C
10
13
9
Assembly Instructions
Step 9
Securing the ladder
Attach the ladder brace
15 12
to ladder side rail
and front right-hand post
4
using bolts . Tighten
bolts using allen key .
E
Q
Step 10
Fixing to wall
This unit must be fixed to
a wall.
Move the bunk bed into
position on the wall.
Position the wall strap
to the top post of upper
back safety rail to
9
mark fixing holes on the
wall. Remove the wall
strap then drill holes and
insert appropriate wall
plugs. Reposition wall
L
strap and fix using
appropriate screws.
L
4
Wall
E
15
12
12
E
L
9
15
E
Warning:
Before drilling,
check wall for
hidden pipes and
cables. Consult a
qualified
L
Wall
specialist if
unsure.
9
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
10
Loading...