Page 1
HYGENA LIDO GLASS TABLE AND 4 CHAIRS
Assembly Instructions - Please keep for future reference
hygena
503/7968
487/6821
Dimensions
Width - 42cm
Depth - 49.5cm
Height - 96cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 13/10/15
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• This product should not be
discarded with household
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 4.4 kgs.
• Maximum safe weight of user:
110kgs.
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Page 3
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
Front leg
1 Left leg
(41 x 44.5 x 1.5cm)
2 Right leg
(43 x 39.5 x 4cm)
3
(43 x 39.5 x 4cm)
Back rest
4 Seat
(35.5 x 67 x 7cm)
5
(42 x 42 x 2cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly of 1 chair. In some cases more
fittings may be supplied than are required.
A
M6 x 22mm Bolt x 4 M6 x 12mm Bolt x 8
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
110 115 120 125 130 135 140 145 150 155 160 165 170
CB
Allen Key x 1
2
Page 4
Assembly Instructions
Step 1
Attach the left leg and
right leg onto the front
leg as shown using
bolts . Then tighten
3
1
B
bolts using allen key .
2
C
B
3
2
B
B
1
B
3
B
1
B
Step 2
Attach back rest onto
left leg and right leg
2 3
as shown using bolts .
Then tighten bolts
using allen key as
shown.
4
A
C
4
A
2
A
A
3
A
3
A
A
3
Page 5
Assembly Instructions
Step 3
Place the seat face
5
down on a raised
protected surface.
Position the chair frame
on the seat as shown
5
and attach through holes
on the left and right
legs using bolts . Then
2 3
A
tighten bolts using allen
key .
C
A
2
A
A
2
A
5
A
3
Carefully turn the chair
upright.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
4
Page 6
HYGENA LIDO GLASS TABLE AND 4 CHAIRS
Assembly Instructions - Please keep for future reference
hygena
503/7968
487/6821
Dimensions
Width - 120cm
Depth - 80cm
Height - 75cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 13/10/15
Page 7
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the product.
• Always lift the product when
moving it around. Never drag.
• Please note wood is a natural
material, some slightly colour
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 24 kgs.
and grain variation and natural
marks will be present.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
Glass Safety
• Keep these instruction for future reference.
• Imported by:
Arogs ltd
489-499 Avebury Boulevard.
Saxon Gate West.
Central Milton Keynes.
Warnings
(a) Do not place very hot or very cold items on the glass surface(s) unless adequately thick mats are
used to prevent such items from coming into contact with the glass.
• If the glass is chipped or broken,stop using the
product and consult the Manufacturer or Supplier.
• Batch No:
Mk92nw
• Date of Manufre:
• Type of glass used: 7mm toughened glass
(b) Do not sit or stand upon the glass surface.
(c) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
(d) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary, do not us washing powders or any other substance containning abrasives since these
substances cscratch glass.
1
Page 8
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
1 Table leg x 4
Table frame
(118.5 x 78.5 x 4cm)
2 Glass top panel
(74 x 3.8 x 3.8cm)
3
(120 x 80 x 1.7cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
M8 x 45mm Bolt x 8 M6 x 8mm Bolt x 4
D E
Spring washer x 8 Allen Key x 1
CB
Flat washer x 8
F
Adhesive pad x 4
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
2
Page 9
Assembly Instructions
Step 1
Place the table frame
upside down on a flat
protected surface.
Attach the legs onto
the table frame as
shown using bolts ,
spring washers and
flat washers . Tighten
bolts using allen key .
2
1
A
D
C
E
Step 2
2
1
2
C
2
1
C
D
A
C
D
A
C
D
D
A
A
2
A
A
D
D
C
C
A
A
2
C
D
C
D
1
C
D
A
C
D
A
Carefully turn the table
frame upright.
Remove backing from
adhesive pads F and
F
carefully paste on the
table frame as shown.
1
Then attach the glass top
3
panel using bolts .
B
Tighten bolts using allen
E
key .
Note:
Take extra care
when handling
and securing the
glass table top. At
least 2 people
required are
required to carry
the glass top.
3
F
B
B
F
B
F
1
B
F
3
F
1
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
3
Loading...